Before Starting The Equipment; Operation - EINHELL TE-DY 18 Li Original Operating Instructions

L sound pressure level ..................... 73.4 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 84.4 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Screwing without hammer action
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
Anl_TE_DY_18_Li_SPK7_THA.indb 14 Anl_TE_DY_18_Li_SPK7_THA.indb 14
= 1.148 m/s
2
h
2
- 14 -
EN
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the time it takes to fi nish the job.
When considering the total time, all steps in the
job cycle need to be taken into account (for ex-
ample, times in which electric tools are switched
off and times in which tools are switched on but
not doing any work, i.e. when they are running
without a load).

5. Before starting the equipment

Be sure to read the following information before
you start using the cordless impact drill:
1. Charge the battery pack with the charger sup-
plied.
2. Only use screwdriver bits that are suited to
the task and in perfect condition.
3. Before you begin screwing into walls and
masonry, check for concealed electric wiring,
gas pipes and water pipes.
Note:
The screwdriver is equipped with a jaw clutch.
The spindle will only start to rotate once the screw
is pushed into the workpiece.

6. Operation

6.1 Charging the Li battery pack (Figs. 2-3)
1. Remove the battery pack (7) from the hand-
le. To do this, press the pushlock button (8)
downward.
2. Check that your mains voltage matches
the voltage shown on the rating plate of the
battery charger. Insert the power plug of the
charger (11) into the socket outlet. The green
LED will start to fl ash.
3. Push the battery pack onto the battery char-
ger.
Section 10 (Charger indicator) includes a table
with explanations of what the LED indicators on
the charger mean.
If the battery pack fails to charge, please check:
•
whether there is voltage at the power socket,
and
12.07.2023 12:33:04 12.07.2023 12:33:04