Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the back cover Remove the 19 fixing screws. (see Fig.5) SCREWS SCREWS Fig.5 How to remove the Pedestal assembly Lay the main unit face down. (see Fig.6) Fig.6 Remove the 4 fixing screws and the pedestal assembly. (see Fig.7) SCREWS Fig.7...
Chassis Board Layout G-BOARD P-UNIT A-BOARD V-BOARD Board Name Function A-Board AV Terminal, HDMI, AV Switch, Sound Processor, TV tuner, PC,SD Card, OFDM, ZWEI, GENX, EEPROM, ADV, Peaks AVC, Speaker out G-Board Side AV Terminal V-Board Remote Receiver, R&G LED, Timer Rec LED, C.A.T.S., SD LED P-Unit Main Input, Power Supply, Inverter Location of Lead Wiring...
Setting Inspection Voltage Confirmation Confirm the following voltages: A board Description Test point Position Voltage TP2765 A03(pin 23) 5V±2% P17V TP2777 A03 (pin 12,13) 17V±2% SUB_F_12V TP2764 A03 (pin 16,17,19 12V±2% INV_ON TP2759 A20 (pin3) 2,85±2%...
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. TX-L37G10E 37FHD Panasonic 2009LCD Self Check Complete 7BC1 O.K.
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on the TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 0.501 OPTION 1 Key Command ADJUST Peaks EEP 00.01.1120 OPTION 2 S e r v i c e 1 WB-ADJ LSI DATA 0.00.0a OPTION 3 OPTION STBY SOFT 1.00.00 Model ID SRV-TOOL STBY EEP 1.03.37 03033100 •...
Option Bytes Description OPTION1 ATP Search speed Slow (1) / Fast (0) TEXT Ch Refresh ON (1) / OFF (0) ID-1 ON (1) / OFF (0) Macrovision Auto-judge ON (1) / OFF (0) Surround enable low bit ON (1) / OFF (0) Surround enable high bit ON (1) / OFF (0) Pre Emphasis...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CA-210 or equivalent) CS-1000A or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 °C.
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List. (IRELAND) (CONTINENTAL)
Page 23
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List. only 32´´ only 32´´ Difference for 37’’...
Replacement Parts List Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is Limited for this item.
Page 38
Cct Ref Parts Number Description Cct Ref Parts Number Description C8316 F1G1C271A117 S.M.CAP 270pF JK4700 K1FY119D0006 HDMI CONNECTOR C8317 F1G1C271A117 S.M.CAP 270pF JK8302 K1NA09E00080 SD SLOT C8319 F1G1C104A116 S.M.CAP 100nF JK8401 K1NA68B00053 CI SLOT C8320 F1G1C104A116 S.M.CAP 100nF K1KA09B00112 9P CONNECTOR C8321 F1G1C104A116 S.M.CAP...
Page 39
Cct Ref Parts Number Description Cct Ref Parts Number Description L5EDD8T00005 LCD PANEL TQB0E0810V CROATIAN TKZC5129 LCD SIDE MTG TQB0E0810W SLOVAKIAN TBM0E1732 MODEL LABEL TQB0E0810X CD ROM N0AC3FJ00001 P UNIT TQB0E0810Z ESTONIAN TKZG5045 P-PCB MTG METAL S I.C.s TBLA0407 PEDESTAL ASSY IC8502 X24CL37G10E EEPROM PEAKS-AVC...
Page 40
Cct Ref Parts Number Description Cct Ref Parts Number Description INSTRUCTION BOOKS TQB0E0812D FRENCH TQB0E0812U ENGLISH I.C.s IC8502 X24CLF37G10 EEPROM PEAKS-AVC TERMINALS AND LINKS K1PY51Y00027 LVDS WIRE A01-K01 TXJA010NFZ WIRE A10-V10 TXJA100NFZ WIRE A12-SPL/ TXJA120NFZ WIRE...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM (Ω) (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.