Do you have a question about the JBL CINEMA SB550 and is the answer not in the manual?
Questions and answers
Richard M Hinkle
January 30, 2025
How to wireless connect fire tablet to JBL Model Cinema SB sound bar and sub woofer
1 comments:
Mr. Anderson
February 10, 2025
To wirelessly connect a Fire Tablet to the Harman JBL Cinema SB550 soundbar and subwoofer, follow these steps:
1. Turn on Bluetooth: Ensure that Bluetooth is enabled on your Fire Tablet. 2. Put the Soundbar in Bluetooth Pairing Mode: - Refer to the JBL Cinema SB550 manual for specific instructions. - Typically, press and hold the Bluetooth button on the soundbar until the indicator light starts blinking. 3. Pair the Devices: - On your Fire Tablet, go to *Settings* > *Bluetooth*. - Look for "JBL Cinema SB550" in the list of available devices. - Tap on it to initiate pairing. 4. Confirm Connection: - Once connected, the soundbar should stop blinking and remain solid. - The Fire Tablet should show the soundbar as a connected audio device. 5. Play Audio: - Any audio from your Fire Tablet should now play through the JBL Cinema SB550 wirelessly.
If the connection fails, restart both devices and try again.
This answer is automatically generated
Richard M Hinkle
January 30, 2025
Want to connect wirless to fire tablet
1 comments:
Mr. Anderson
February 10, 2025
To connect the Harman JBL CINEMA SB550 wirelessly to a Fire tablet via Bluetooth, follow these steps:
1. Power On: Turn on the JBL CINEMA SB550 soundbar. 2. Enable Bluetooth Pairing: Press the Bluetooth button on the soundbar to enter pairing mode. The soundbar should be discoverable. 3. Open Bluetooth Settings on Fire Tablet: On the Fire tablet, go to Settings > Bluetooth and turn Bluetooth on. 4. Select the Soundbar: In the list of available devices, find and select JBL CINEMA SB550. 5. Complete Pairing: Wait for the connection to establish. The soundbar should indicate a successful connection.
Now, audio from the Fire tablet will play through the JBL CINEMA SB550 soundbar.
IMPORTANT SAFETY INSTRUCTIONS Verify Line Voltage Before Use The JBL CINEMA BAR SB550 (soundbar and subwoofer) has been designed for use with 100-240 volt, 50/60 Hz AC current. Connection to a line voltage other than that for which your product is intended can create a safety and fire hazard and may damage the unit.
1. INTRODUCTION Thank you for purchasing the JBL CINEMA BAR SB550 (soundbar and subwoofer) which is designed to bring an extraordinary sound experience to your home entertainment system. We encourage you to take a few minutes to read through this manual, which describes the product and includes step-by-step instructions for setting up and getting started.
Wall-mounting kit 2. WHAT’S IN THE BOX Unpack the box carefully and ensure that the following parts are included. If any part is damaged or missing, do not use it and contact your retailer or customer service representative. Main unit Product information &...
3. OPTICAL (TV) 3. PRODUCT OVERVIEW • Connect to the optical output on your TV. 3.1 Controls and indicators 4. USB USB connector for software update (for service only). • • Connect to USB storage device for MP3 file playback (for US version only).
3.4 Remote control 6. Sound effect buttons VOICE • Select the pre-defined EQ (equalizer) settings for news. MUSIC • Select the pre-defined EQ (equalizer) settings for music. MOVIE • Select the pre-defined EQ (equalizer) settings for movie. • Select the bass level for subwoofer: 1/2/3 (default)/4/5. •...
3. As shown in the diagram, remove the fastening screw by 4. PLACEMENT using a screwdriver. 4.1 Desktop placement 4. Fasten the wall-mounting screw included in the supplied mounting kit. Place the soundbar and subwoofer on a flat and stable surface. 5.
3. On your Bluetooth device, enable Bluetooth and search for – Contact your TV manufacturer if you have problems with the HDMI- “JBL CINEMA SB550” within three minutes. CEC compatibility of your TV. → Connected: The status indicator turns solid blue ( ). A confirmation tone is heard.
“5.2.1 Connect a Bluetooth device”. • If the device has ever been paired with the soundbar, first unpair “JBL CINEMA SB550” on the device. NOTES: – The Bluetooth connection will be lost if the distance between the soundbar and Bluetooth device exceeds 10 m / 33 ft.
6.2 Play from the TV source 6.2.2 TV remote control learning Through IR learning, you can program the soundbar to accept IR With the soundbar connected, you can enjoy TV audio from the commands from your TV remote control, and then use your TV soundbar speakers.
6.3.1 Control music playback 7. SOUND SETTINGS In Bluetooth mode, you can control music playback through the buttons on the remote control or on the soundbar. 7.1 Pre-defined EQ settings With the remote control, select the pre-defined EQ (equalizer) effects to suit your video or music. Button Function •...
8. RESTORE FACTORY SETTINGS 9. RE-CONNECT THE SUBWOOFER The soundbar and subwoofer are paired at factories. After power- on, they are paired and connected automatically. In some special > 10S cases, you may need to pair them again. 1. Press to switch on.
Page 14
Dimensions 10. PRODUCT SPECIFICATIONS • Soundbar dimensions (W x H x D): 950 x 64 x 80 mm / 37.4" x 2.5" x 3.1" General specification Subwoofer dimensions (W x H x D): • • Model: CINEMA SB550 200 x 324 x 250 mm / 7.9" x 12.8" x 9.9" •...
Page 15
Remote control 11. TROUBLESHOOTING The remote control does not work. Never try to repair the product yourself. If you have problems • Check if the batteries are drained. If so, replace them with using this product, check the following before you request new ones.
Page 16
® owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners. The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Need help?
Do you have a question about the JBL CINEMA SB550 and is the answer not in the manual?
Questions and answers
How to wireless connect fire tablet to JBL Model Cinema SB sound bar and sub woofer
To wirelessly connect a Fire Tablet to the Harman JBL Cinema SB550 soundbar and subwoofer, follow these steps:
1. Turn on Bluetooth: Ensure that Bluetooth is enabled on your Fire Tablet.
2. Put the Soundbar in Bluetooth Pairing Mode:
- Refer to the JBL Cinema SB550 manual for specific instructions.
- Typically, press and hold the Bluetooth button on the soundbar until the indicator light starts blinking.
3. Pair the Devices:
- On your Fire Tablet, go to *Settings* > *Bluetooth*.
- Look for "JBL Cinema SB550" in the list of available devices.
- Tap on it to initiate pairing.
4. Confirm Connection:
- Once connected, the soundbar should stop blinking and remain solid.
- The Fire Tablet should show the soundbar as a connected audio device.
5. Play Audio:
- Any audio from your Fire Tablet should now play through the JBL Cinema SB550 wirelessly.
If the connection fails, restart both devices and try again.
This answer is automatically generated
Want to connect wirless to fire tablet
To connect the Harman JBL CINEMA SB550 wirelessly to a Fire tablet via Bluetooth, follow these steps:
1. Power On: Turn on the JBL CINEMA SB550 soundbar.
2. Enable Bluetooth Pairing: Press the Bluetooth button on the soundbar to enter pairing mode. The soundbar should be discoverable.
3. Open Bluetooth Settings on Fire Tablet: On the Fire tablet, go to Settings > Bluetooth and turn Bluetooth on.
4. Select the Soundbar: In the list of available devices, find and select JBL CINEMA SB550.
5. Complete Pairing: Wait for the connection to establish. The soundbar should indicate a successful connection.
Now, audio from the Fire tablet will play through the JBL CINEMA SB550 soundbar.
This answer is automatically generated