HP 11729B Operating And Service Manual page 6

HP 11729B
CONTENTS
Contents
Pam
Section I
GENERAL INFORMATION
Introduction
....................................
l-l
Specifications
...................................
1-l
Safety Considerations ...........................
1.1
Instruments Covered by This Manual
...........
1.1
Manual Changes Supplement
................... I-1
Description .....................................
l-2
Options .........................................
1.2
Electrical Options .............................
l-2
Mechanical
Options ...........................
1-3
Accessories Supplied ............................
1.3
Equipment
Required But Not Supplied ........... l-3
Electrical Equipment Available
.................
1-3
Recommended Test Equipment
.................. l-4
Section II
INSTALLATION
Introduction
....................................
z-1
Initial Inspection ...............................
2-l
Preparation For Use ............................
2-1
Power Requirements
..
A Line Voltage and Fuse Selection
.......................................
2-l
2-l
Power Cables .................................
2-1
HP-IB Address Selection ......................
2-2
Interconnections ..............................
2-3
Mating Connectors ...........................
2-3
Operating Environment .......................
2.3
Bench Operation
..............................
2-5
Rack Mounting
...............................
2.6
Storage and Shipment ..........................
2-5
E nvironment .................................
2-5
Packaging ....................................
2.5
Section Ill
OPERATION
Introduction
3-1
Local Operation
3.1
Remote Operation (HP-I@ t
3-l
Operator's Checks
t .
3-1
Operator's Maintenance
3.1
Operator's Checks
. t t
3.1
General Operating Instructions
3-14
TurnOn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14
Phase Noise Measurement
3.14
Phase Detector Method
3.14
Frequency Discriminator Method
3.22
AM Measurement (Option 130 only)
8-24
SectIon IV
PERFORMANCE TESTS
Introduction
.................................... 4-1
Equipment Required
............................
4-I
Teat Record .....................................
4-1
Calibration Cycle ...............................
4.1
Page
Measurement Frequency Range,
IF Output Bandwidth and
Level Performance Tests
4-l
Residual Phase Noise Performance Test
(Using a test signal less than 1280 MHz) ....... 4-4
Residual Phase Noise Performance Test
(Using a test signal of 10 GHz) ................ 4-9
AM Noise Floor Performance Test .............. 4-14
Section V
AOJUSTMENTS
Introduction
.................................... 5-1
Safety Considerations
........................... 5.1
Equipment Required ............................
5-I
Factory Selected Components
................... 6-1
Related Adjustments ............................
5-l
Power Supply Adjuetment .......................
5.2
Phase Lock Indicator Adjustment
............... 5-3
Option Switch Adjustment ......................
5-8
Attenuator AT1 Selection
...................... 5.10
Section
VI
REPLACEABLE PARTS
Introduction ....................................
6-1
Abbreviations
.................................. 6-l
Replaceable Parts Liat ..........................
6-l
Factory Selected Parts (*) .......................
6-1
Parta List Backdating
(-,) ........................ 6-1
Parts List Updating
(Change Sheet) ............. 6-l
Illustrated Parts Breakdown
..................... 6-l
Hardware ......................................
6.1
Ordering Information ...........................
6.1
Recommended Spares List
...................... 6-2
Sectlon VII
MANUAL CHANGES
Introduction ....................................
7-l
Manual Changes
............................... 7-l
Manual Change In&ructions ....................
7"l
Section VIII
SERVICE
Introduction
.................................... S-l
Service Sheet e ..................................
8-l
Block D' lagTam% .............................. 8-l
Schematics
................................... 8-l
Safety Considerations ...........................
8-l
Before Applying
Power ........................ 8-l
safety ........................................
8-l
Recommended Test Equipment .................. 8-l
Service Tools, Aids and Information
............. 8-l
Pozidriv Screwdrivers .........................
8-l
TuningTools
.................................
8.2
Heat Staking Tools ...........................
8-2
Hardware ....................................
8-2
Ma.intenance
.................................
8-2