Table of Contents
Advertisement
Checking and selecting the input and output
sources using the menu
You can display the menu to see which input sources are
selected for the TV screen and PIP screen, and which output
source is selected. You can also select them on the menu dis-
play.
Select » Video Connection« with A + o V — and press OK. The
VIDEO CONNECTION menu appears. (See Fig. 41).
You can see which source is selected for the TV and PIP input,
and for the output. If you want to select the input and output on
this menu, go on to the next step.
Select TV screen (input source for the TV screen), PIP (input
source for the PIP screen), or Output (output source) with A + or
V - and press OK, One of the source items changes colour.
(See Fig. 42.)
Select the desired source with A + 0 V -. (See Fig. 43.)
For details about each source, see the table on page 22.
Press OK.
The selected source is confirmed, and the cursor appears.
{See Fig. 44.)
Repeat steps 2 to 4 to select the source for other inputs or out-
puts.
When recording
When you use the @
(record) button, make
sure to press this but-
ton and the one to the
right of it simulta-
neously.
e Do not move the
Remote Commanders
during programming.
After programming,
check to see if all
the programmed
functions work. It may
be the case, thata
function cannot be
programmed.
When you want to
operate the audio or
video equipment
Make sure that the
VTR 1/2/3 MOP
selector is set to the
position you used dur-
(Ag programming.
When you replace the
Remote Commander
batteries, the pro-
grammed functions
remain stored tor 30
minutes without a bat-
tery.
When the memory of
the programmable
Remote Commander
is full, the MEM indi-
cator lights up.
24
Remote Control of Other
Equipment
You can use the TV Remote Commander to controt other remote-controlled equipment. The but-
tons for video operation have been factory-set to control most of Sony video equipment, such
as: Beta, 8mm or VHS VTRs or video disc players.
Additionally you can programme these buttons to control also audio and video equipment of
other manufacturers.
Tuning the Remote Commander to Sony equipment
1.
Setthe VTA 1/2/3 MOP selector according to the equipment you want to control:
VTR 1: Beta or ED Beta VTR
VTR 2: 8mm VTR
VTR3:
VHS VTR
MOP:
Video disc player
2.
Use the buttons indicated in the illustration to operate the additional equipment.
lf your video equipment is tumished with a COMMAND MODE selector set this selector to the
same position as the VTR 1/2/3 MOP selector on the TV Remote Commander.
If the equipment does not have a certain function, the corresponding button on the Remote
Commander will not operate.
Tuning the Remote Commander to audio or video equipment of
other manufacturers
Your TV Remote Commander is a programmable Remote Commander. This means that you
can programme the buttons indicated In the illustration with functions of other Remote Com-
manders. A function can be stored on any of the buttons and on ail four levels of the VTR 1/2/3
MOP selector.
Programming a function
1
Set the MEM/USE switch to MEM (memorize).
2
Set the VTR 1/2/3 MOP selector to the desired position.
3
Position the two Commanders head to head (see illustra-
tion).
4
First press the button on the TV Remote Commander onto
which you want to programme a function. Now the MEM
indicator on the Remote Commander tights up.
5
Then press the button on the other Remote Commander, the
function of which you want to programme. As soon as the
MEM indicator goes out, the function is stored.
6
Repeat steps 4 and 5 for ail other functions you want to pro-
gramme. When you have programmed all buttons on one
lavel of the VTR 1/2/3 MOP selector, select another level.
7
When you have finished programming, set the MEM/USE
switch to USE.
Clearing programmed functions
1
Set the MEM/USE switch to MEM.
2
Set the VTR 1/2/3 selector to the level of functions you want
to clear.
3
Press any of the programmable buttons. Now the MEM indi-
cator lights up.
4
Keep the RESET button pressed, using the tip of a pen, until
the MEM indicator has flashed four times. Now all program-
med functions on this fevel are cleared.
5
Reset the MEM/USE switch to USE.
Advertisement
Table of Contents
