Page 1
Important: Product 08674 is supplied with a 2.0Ah battery pack and charger. The battery pack must be charged IMMEDIATELY after purchase and every two months thereafter. SELF-PROPELLED PETROL LAWN MOWERS 08673 & 08674 Please note that model number 08674 is illustrated throughout this instruction booklet.
All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product.
Read this manual in full before attempting to assemble, considered misuse. Draper Tools accepts no operate or maintain the product and retain it for later use. responsibility for improper use of this product.
Page 5
*Draper Tools recommends using an additive or stabiliser with E10 petrol so the fuel can be safely stored in the fuel tank for longer.
4. Health and Safety Information Important: Read all the Health and Safety instructions Operation before attempting to operate, maintain or repair this • Do not operate the engine in confined spaces where product. Non-compliance with these instructions may dangerous carbon monoxide fumes can collect. result in injury or damage to the user or the product.
4. Health and Safety Information − Checking, cleaning or adjusting the lawn mower. • Observe all basic Health and Safety precautions when working with machines and mechanical tools in an − Inspecting the lawn mower for damage after outdoor environment. striking a foreign object or if it begins to vibrate abnormally.
4. Health and Safety Information 4.3 Additional Safety Information 4.4 Additional Safety Instructions for Machines with a Petrol Engine for Rechargeable Batteries Important: Use ONLY the battery pack and charger • NEVER smoke in the vicinity of the machine, especially during refuelling. supplied with this product. DO NOT use this charger with any other batteries.
If the power supply cord is damaged, it must be replaced by Draper Tools, an authorised service agent or similarly qualified personnel in order to avoid a hazard. The damaged or incomplete plug, when cut from the cable, shall be disabled to prevent connection to a live electrical outlet.
1 x Collection bag (not shown) 4 x M6 x 32mm screws (08674 only) 1 x Lower handle frame 3 x M5 x 30mm bolts with wingnuts (08673 only) 1 x Side discharge chute 1 x Spark plug spanner body...
6. Preparing the Lawn Mower Important: Before assembling, fuelling or adjusting this d. Remove the lock nut and one washer from each of product, read and understand all the safety instructions the two bolts (I) and pass the bolts inwards through listed in this manual.
Page 13
6. Preparing the Lawn Mower Important: Ensure that the drive lever cable passes 2. Install the control panel or cup holder: under the engine operation lever attachment point. a. Stand behind the handle and push the left arm of the engine operation lever (8) away from the d.
6. Preparing the Lawn Mower 6.2 Assembling and Attaching the 2. Holding the collection bag frame handle, hook the front loop of the frame over the tab beneath the rear Collection Bag discharge cover. If required, the collection bag netting can be detached 3.
6. Preparing the Lawn Mower 6.3 Installing the Mulching Plug and Side 6.4 Selecting a Cutting Mode Discharge Chute The lawn mower can be set to operate in the following cutting modes, which are selected by installing the To install the mulching plug, remove the collection bag appropriate combination of accessories: (2) from the rear of the mower and insert the mulching plug (14) into the rear discharge opening with the handle...
(21) that rusts the fuel system from the inside. Draper Tools recommends the use of petrol additives or stabilisers when using E10 petrol. Additives and stabilisers are widely available and can extend the length of time that E10 petrol can be safely stored in a product fuel tank.
Some petrol brands contain other quantities of ethanol. 6.8 Charging the Battery Pack Do not use fuels with more than 10% ethanol in Draper products. CAUTION! This battery MUST be charged for at least three hours immediately after purchase Always store and dispose of fuels responsibly and in and at least once every three months thereafter.
Remove the battery and check for obstructions and debris around the charging contacts. If the problem is not resolved, stop charging the battery immediately and contact Draper Tools for support. 6.9 Inserting and Removing the...
7. Operating Instructions Important: Before operating this product, read Starting Stock No. 08673 and understand all the safety instructions listed in 1. Check and top up the fuel and engine oil levels as this manual. appropriate and move the lawn mower to its starting WARNING! Using this mower can pose a danger position.
Page 20
7. Operating Instructions 4. Stand behind the lawn mower and depress the engine operation lever (8) to the foam handle. Stock No. 08673 shown (18) Fig. 27 Important: It may help to depress the engine Fig. 25 operation lever (8) when extending the recoil starter;...
• Aim to cut no more than one-third of the grass height during each operation. To stop the lawn mowers, release the engine operation − Draper Tools recommends that the lowest cutting lever and allow the rotating blade to come to a complete height is not used for the first cut of the year and stop.
For safety maintenance. NEVER attempt to perform any reasons, Draper Tools recommends that the blade is maintenance with the blades rotating unless it is sharpened, balanced and mounted by an authorised specifically stated in this manual.
Check the oil level before EVERY use. 1. With both control levers (6) and (8) disengaged, Draper Tools recommends draining the fuel when the loosen the fuel tube clip with pliers and remove the motor is hot to allow the oil to drain more quickly and fuel pipe from the fuel tank.
8. Maintenance & Troubleshooting 8.6 Air Filter Care 8.7 Spark Plug Care Clean the air filter chamber regularly to ensure a Ensure that the spark plug is clean and the gap is correct. consistent airflow. The spark plug may become contaminated over time if the machine is run with part-throttle for prolonged WARNING! NEVER use petrol or solvents to periods.
8. Maintenance & Troubleshooting If the mower is to be stored for a prolonged period, ensure that the engine cylinder is sufficiently lubricated to prevent it from seizing: 1. Remove the spark plug; see 8.7 Spark Plug Care. 2. Pour a few drops of SAE 10W-30 oil into the socket. 3.
(see 6.6). The engine has not been primed Press the priming bulb six times until (08673 only). fuel can be seen in the fuel lines. The fuel has been stored for too long. Drain the fuel (see 8.4) then refill the fuel tank (see 6.6).
Page 27
The mower delivers an The blade is blunt or damaged. Have the blade resharpened or uneven finish. replaced; contact Draper Tools for support. The cutting height is set too low. Adjust the cutting height to a higher position (see 6.5).
Draper Tools Product Helpline for details of your nearest authorised agent. Draper Tools will endeavour to hold any spare parts, if applicable, for seven years from the date that it sells the final matching stock item.
This warranty period covers parts and labour for 12 months from the date of Your Draper Tools guarantee is not effective until you can purchase. Where tools have been hired out, the warranty produce, upon request, a dated receipt or invoice to period covers 90 days from the date of purchase.
11. Explanation of Symbols Disconnect the spark plug cable before Read the instruction manual maintenance WARNING! Keep hands away from spinning blades WARNING! Risk of danger to wildlife Do not use on sloped ground WARNING! Hot surfaces Do not use this product indoors WARNING! Risk of fire Engine displacement Engine horsepower...
Page 31
11. Explanation of Symbols Product weight (gross) WEEE – Waste Electrical & Electronic Equipment Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish European conformity UK Conformity Assessed Continuous A-weighted sound power level – 31 –...
Need help?
Do you have a question about the 08673 and is the answer not in the manual?
Questions and answers