Optex LINK-BT1 C Manual

■ Points regarding operation checks
This product uses Bluetooth LE wireless communication. This unit must accept any interference, which may cause a delay in recognition of the signal,
including interference that may cause undesired operation of this unit. The transmitting distance may be reduced by environment conditions and
mechanical noise.
After installation, check the operation of the system according to the following points.
• If there are shutters or windows nearby, does the system operate correctly regardless of whether shutters or windows are open or closed?
• Does the system operate correctly when machinery nearby is in operation?
• If a parking lot is nearby, does the system operate correctly regardless of whether vehicles are present or not?
• If vehicles, automatic transfer devices, or similar items pass by in the vicinity, does the system operate correctly when such items pass by?
Under normal operating conditions LINK-BT1 C signal may encounter interference, this unit must accept any interference.
Do not use this product in safety applications, applications where real-time performance is required, and applications where
WARNING
signal delays are not permitted.
Be sure to check the operation.
CAUTION • Do not use this product in environments where it is close to apparatuses that generate extremely strong radio waves or noise.
• Using this product together with a wireless LAN that uses the 2.4 GHz band will lead to radio wave interference and may
result in unstable communication.
6
Troubleshooting
Symptom Cause
Operation indicator does not The power supply wires are improperly connected.
turn ON. No Power
Power supplied my not meet specifications.
LINK-BT1 C will not pair with Bluetooth LE signal strength is poor.
a compatible sensor.
The communication range has been exceeded.
The pairing procedures were not followed.
The maximum number of pair LINK-BT1 C has
been exceeded.
A compatible sensor is paired The relay output wiring is not correct.
with the LINK-BT1 C unit. Output contact type is incorrect.
You walk into the The device to be triggered is not connected to power.
corresponding sensor The LINK-BT1 C operation indicator is blinking
detection area, that is alternating purple and yellow. Pairing has been
responsible for triggering the lost between the LINK-BT1 C and the
LINK-BT1 C output contact compatible sensor.
relay, but the unit does not The Bluetooth LE signal is poor.
operate correctly.
If symptoms persist after following the troubleshooting step above, contact your installation company or service provider.
FCC and ISED Statement
This device complies with part 15 of FCC Rules and Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC NOTICE
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
FCC/ISED Radiation Exposure Statement
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of
the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy.
Cet équipement est conforme aux limites d'exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes
directrices d'exposition et d'exposition aux fréquences radioélectriques (RF) CNR-102 de l' ISDE puisque cet appareil a une niveau tres bas d'energie RF.
* The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by OPTEX CO., LTD. is under license.
Contact
Europe, Middle-East and Africa Subsidiary
OPTEX TECHNOLOGIES B.V.
Henricuskade 17, 2497 NB The Hague, The Netherlands
www.optex-europe.com
North and South America Subsidiary
OPTEX INCORPORATED
10741 Walker Rd. Suite 300 Cypress, CA 90630 U.S.A
Copyright (C) 2020 - 2022 OPTEX CO., LTD.
www.optexamerica.com
Action
Verify power supply wires are connected to the power terminals.
Check main power sources for unit.
Power supply should be between 12 to 24 VAC ±10 % (50/60 Hz) / 12
to 30 VDC ±10 %.
Relocate the LINK-BT1 C away from any machinery that generates
electrical noise.
Move the LINK-BT1 C closer to the compatible sensor.
Follow the recommended pairing procedure.
Do not pair more than five LINK-BT1 C units to one compatible
sensor.
Connect to the output terminals correctly.
Verify that the correct relay logic was selected N.O./N.C.
Connect power to the device.
Disconnect and reconnect power to both the compatible sensor and
LINK-BT1 C. If the problem persists, reduce the distance between
the LINK-BT1 C and compatible sensor to improve signal strength.
Relocate the LINK-BT1 C away from any machinery that generates
electrical noise.
Manufacturer
OPTEX CO., LTD.
5-8-12, Ogoto, Otsu, Shiga, 520-0101 Japan
Tel : +31(0)70 419 41 00
Legal representative (UK only)
OPTEX (EUROPE) LTD.
Unit 13 Cordwallis Park Clivemont Road
SL6 7BU Maidenhead, Berkshire
Tel : +1(800)877 6656 United Kingdom
Wireless dry contact converter
LINK-BT1 C
5929012 DEC 2022
1
Manufacturer's statement
■This product is used to connect to a compatible sensor via Bluetooth LE wireless communication and convert the signal received from the sensor to a
relay output. Only use this product as specified in this manual. This product cannot be used in a standalone manner. A compatible sensor is required.
■This product uses Bluetooth LE wireless communication. This product must accept any interference, including interference that may cause undesired
operation of this product. Fully understand the function of the product prior to installation.
Note: This product should not be used in safety applications, applications where real-time performance is required, and applications where signal
delays are not permitted.
Note: OPTEX is not liable for secondary damage attributable to this product failing to operate normally.
■To use this product, download the required App for the compatible sensor to your smartphone or handheld devices. Furthermore, this product should
not be installed in environments where the App cannot be used.
• Read this manual thoroughly before installing this product to ensure correct usage.
• After reading this manual, store the manual in a safe place. So it can be referred to as necessary.
• The description given here is for the correct usage of the product without causing bodily harm or personal injury or damage to property.
Please read the warning, graphical symbol indication, understand their meaning before proceeding with the installation of the LINK-BT1 C.
The marks and their meanings are as follows:
WARNING
Failure to follow the instructions provided with this indication and improper handling may cause death or serious injury.
CAUTION
Failure to follow the instructions provided with this indication and improper handling may cause injury and/or property damage.
EXAMPLES OF GRAPHICAL INDICATION
This △ symbol indicates CAUTION, a detailed indication of the hazard is provided in the center of the symbol (the figure to the left
indicates danger of electric shock).
The symbol indicates prohibited. The specific warnings are indicated in or near the symbol (the figure to the left indicates that
disassembly of the product is prohibited).
The symbol indicates a mandatory action or an item to be observed. The specific instructions are indicated in or near the symbol
(the figure to the left indicates that power should be disconnected).
Do not touch with wet hands Do not handle sensor, unit and or power supply with wet hands. Electric shock may occur.
Do not disassemble or alter the product NEVER perform disassembly or modification of the unit which is dangerous. Fire or electric shock may occur.
The use of this product under abnormal conditions may result in electrical shock, fire, smoke, and or
In the event, the product malfunctions,
smell of smoke. In the event the product malfunctions immediately disconnect power and contact your
disconnect power
service provider or installation company.
Use the product only within the scope Use the product within the scope of the specifications described within this manual. Failure to follow
of its specifications specifications may result in fire and or electrical shock.
Before installation always disconnect Before starting the installation and or wiring of the product, always disconnect the power. Electrical
power shock may occur.
Do not touch any electronic
Electric shock and or injury may occur.
component's during operation.
A malfunction may result if the product is dropped, impacted, and or forcefully shaken, which could result in a
Impact prohibited
fire, and or electrical shock.
Do not high pressure wash the Do not submerge the product into the water, high-pressure washer, and or direct spray with a water hose.
product Washing the product could result in a malfunction.
Verify electrical connections are Follow the steps described in this manual for wiring or fire and or electric shock may occur.
properly secured.
Securely fastened the sensor and or The products may fall resulting in death or injury. The cable may come loose, resulting in injury, fire, and or
wiring electric shock.
Install and configure each product Follow the steps described in section 4 & 5 of this manual for proper installation, configuration, and operation
properly check. Improper setup could result in malfunction resulting in death, injury, fire and or electrical shock.
Regularly inspect the unit Please inspect the unit regularly. If you find any abnormality, do not use it.
ENGLISH
WARNING
CAUTION