Advertisement
<PRO 4>
<PRO 5>
<Code setting>
<Reset setting>
CUSTOM
setting
<PRO 6>
<Normal mode>
In case of Window comparator mode or Hysteresis mode (The follow-
ing diagram shows when the Window comparator mode is selected.)
Setting of thresh-
<PRO 7>
old tracking
<Setting of threshold value tracking>
Threshold tracking is OFF
Select the threshold tracking cycle
in the range of 1 to 9,999 sec.
Tracks threshold when the output is OFF
Tracks threshold when the output is ON
Not stored in EEPROM
Select the cycle of storage in EE-
PROM in the range of 1 to 250 sec.
Start tracking at the time the output
turns OFF after power is ON
Start tracking at the time the output
turns ON after power is ON
Notes 1) Display for laser amount can show the digit of max. 4,000 if "
speed or "
" for high speed is selected in the response time setting "
but will display the digit of max. 9,999 if "
distance is selected.
2) Level 4 of the light-receiving sensitivity can be set only when "
distance (response time: 4ms or less) is set at the response time setting "
3) In order to clear the value, set the time period holding function to OFF once. Turn-
ing the power OFF can also clear the value.
Default
Item
setting
Response time
Sets response time.
setting
Sets operation and period of the timer.
Timer setting
This setting works in conjunction with the timer mode.
For the timer mode, refer to "
Hysteresis can be set when the normal mode or the
Hysteresis setting
window comparator mode is selected.
Shifts the threshold value by a certain percentage in-
Shift setting
crement in limit teaching.
Light-receiving
Selects light-receiving sensitivity from 3 levels [4 levels,
sensitivity setting
only for ultra long distance (U-LG)].
Emission halt
Selects laser emission from the sensor head to execute
setting
or halt.
When setting to "
Digital display
the jog switch in RUN mode, incident light intensity, in-
setting
cident light intensity in percentage or the peak / bottom
value can be displayed on the digital display (red).
Power consumption can be lowered.
"
"
Eco setting
"
"
Time period
hold setting
"
Refer to "Code setting table."
: Select code, shift decimal point
: Confirmed
(Blinks)
(Blinks 3 times)
Response
<CUSTOM setting>
time setting
Response time setting
Light-receiving sensitivity
setting
Emission halt setting
Setting of data bank loading
Code setting
<Output mode>
Normal mode
Window comparator mode
Rising differential mode
Trailing differential mode
Hysteresis mode
Forced ON output mode
Forced OFF output mode
Shift value setting
(displayed in percentage)
<Shift value setting>
Setting of threshold
tracking cycle
(OFF)
Output
setting
(OFF)
Storage
cycle setting
(OFF)
Start
setting
(OFF)
" for standard or "
Description
TIMER MODE."
" (lock OFF) and pressing
": Eco OFF
": If any key operation is not carried out for 20 sec.
in RUN mode, the digital display turns OFF.
"： If the key lock function is set to ON in RUN
mode, the digital display turns OFF.
"： Peak / bottom value in the digital display re-
freshing condition can be displayed.
"： Peak / bottom value in the hold condition can
be displayed.
Item
Setting of data
bank loading
Automatic
<RUN mode>
Setting of data
bank saving
Output 1 / 2
Copy setting
Output 1
Output 1
Output 1
Output 1
Output 1 / 2
Output 1 / 2
Communication
enable / disable
setting
Communication
protocol setting
Backup setting
Code setting
Reset setting
CUSTOM setting
Output mode
" for ultra high
",
" for ultra long
" for ultra long
".
Setting of
threshold track-
ing cycle (Note)
Output
setting
Storage
cycle setting
Start setting
Note: Conducts the limit teaching for the changed incident light intensity.
Shift direction of the threshold differs depending on the combination of the output status
and the output operation.
Output status
Output ON
Output ON
Output OFF
Output OFF
Default
Description
setting
Loads configuration setting from the data bank.
"
"： Select this mode when only one amplifier to
load.
"
"： Select this mode when all the cascading
amplifiers to load in a lump by optical
communications.
For the optical communications, refer to "
OPTICAL COMMUNICATIONS."
Saves configuration setting to the data bank.
"
"： Select this mode when only one amplifier to
save.
"
"： Select this mode when all the cascading
amplifiers to save in a lump by optical
communications.
For the optical communications, refer to "
OPTICAL COMMUNICATIONS."
Using optical communications, configuration settings
from the main amplifier are copied to all of the sub am-
plifiers connected on the right side of the main control-
-
ler connector.
However, except the data bank loading / saving.
For optical communications, refer to "
COMMUNICATIONS."
When conducting the copy setting or setting of data
bank loading / saving from the main amplifier via optical
communications, it is possible that only the sub ampli-
fier which is set to communication disable "
not to receive the set contents.
When conducting the copy setting or setting of data bank
loading / saving from the main amplifier via optical com-
munications, the optical communications through a sub
amplifier which is set to communication halt "
and the following sub amplifiers can be halted.
Allows to save or not to save the threshold value by
teaching in EEPROM.
Consistent setting can be done by inputting 8-digit code
instead of independent setting.
In addition, present setting can be confirmed.
If setting to "
", returns to default settings (factory
-
settings).
Selects an item in CUSTOM mode to display.
Sets output 1 and output 2 individually.
<Settable for both output 1 and 2>
"
"： Normal mode
Sets a threshold value for ON / OFF operation.
"
"： Forced ON output mode
Sets forcibly the output to ON.
"
"： Forced OFF output mode
Sets forcibly the output to OFF.
<Settable only for output 1>
"
"： Window comparator mode
Judges if set two threshold values are within
the required range or not. This can be se-
lected in 1 / 2 / 3-point teaching.
"
"：Rising differential mode
Only drastic rises in incident light intensity are
detected.
"
"： Trailing differential mode
Only drastic drops in incident light intensity
are detected.
"
"： Hysteresis mode
Changes hysteresis to ignore small change of
incident light intensity.
This can be selected in 1 / 2 / 3-point teaching.
This mode can change the threshold value depending
on the cycle (1 to 9,999 sec.) that is set with the varia-
tions of the incident light intensity. The tracking shift
amount is the one which is set at the <Shift setting>.
Selects whether tracking threshold when the output is
OFF or when the output is ON.
Selects a threshold storage cycle in EEPROM from 1 to
250 sec.
Selects whether start tracking threshold at the time the
output turns OFF or at the time the output turns ON
after power is ON .
Output operation Shift direction
Light-ON
- side
Dark-ON
+ side
Light-ON
+ side
Dark-OFF
- side
OPTICAL
",
"
Advertisement
