Related Manuals for ZKTeco FaceDepot 4A
Summary of Contents for ZKTeco FaceDepot 4A
- Page 1 Quick Start Guide FaceDepot 4A Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
- Page 2 Overview Near-infrared Flash Camera Indicator Light Fingerprint Sensor Card Reading Area Front Side Speaker Reset Bottom 193mm Rear Note: 1. When verification is successful, the indicator light turns green, and when verification fails, the indicator light turns red. Remove the back cover of the device, you can set the SIM card and back-up battery by yourself.
-
Page 3: Connection Cables
Connection Cables Power In Network 485A 485B ALARM+ ALARM- RS485 & RS232 Alarm WD0-OUT WD1-OUT INWD0 INWD1 12V-OUT Lock, Door Sensor, Wiegand Exit Button & Auxiliary Input Standalone Installation Alarm Smoke Detector Printer Door Sensor Exit Button Card ZKBio Access IVS TCP/IP Lock ZKBio Time... -
Page 4: Power Connection
Power Connection AC Adapter DC 12 3A Recommended power supply 12V ± 10%, at least 3,000mA. To share the power with other devices, use a power supply with higher current ratings. Ethernet Connection Connect the device and computer software over an Ethernet cable. As shown in the example below: ZKBio Access IVS ZKBio Time... -
Page 5: Alarm Connection
RS485 and RS232 Connection The RS485 and the RS232 lets user connect to multiple readers to the device. The RS232 and RS485 can be connected to the terminal, as shown in the figure below. 485A RS485 485B Reader RS232 Printer Alarm Connection ALARM+ ALARM-... -
Page 6: Lock Relay Connection
Lock Relay Connection The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (normally opened when powered) is connected with 'NO1' and 'COM' terminals, and the NC Lock (normally closed when powered) is connected with 'NC1' and 'COM' terminals. The power can be shared with the lock or can be used separately for the lock, as shown in the example with NC Lock below: 1)Device not sharing power with the lock 2)Device sharing power with the lock... -
Page 7: Wiegand Connection
Wiegand Connection Wiegand card reader connects to the top 4 pins of the wiegand terminal and the last two pins are used by the Access controller, as shown in the following figure. It sends the credentials to the device via wiegand communication. WD0-OUT WD1-OUT 12V-OUT... - Page 8 Method 2: Registering on ZKBio Time Software Register on the PC Please set the IP address and cloud service server address on the device. Click [Device] > [Device] > [Add] to add the device to the software. It can automatically be added when the device's server address and port are set. Personnel Device Attendance...
- Page 9 Click [Personnel] > [Employee] > [Employee] > [Add] to register users in the software. Synchronize personnel on the software to the devices in the corresponding area. In the personnel list, select an employee(s) and click [More] > [Resynchronize to device] to access the confirmation interface for synchronizing. For more details, please refer to the ZKBio Time User Manual.
- Page 10 Method 3: Register on ZKBio Access IVS Software Register on the PC Please set the IP address and cloud service server address in the Comm. Menu option on the device. Click [Attendance] > [Attendance Device] > [Authorized Device] to search the device on the software.
- Page 11 Register on the Phone Once the ZKBio Access IVS software is installed, the users could enroll their face via a browser application on their own mobile phone. 1. Click [Personnel] > [Parameters], input ‘’http://Server address: Port’’ in the QR Code UGL bar. The software will automatically generate a QR code. Scan the QR code or login onto ‘’http://Server address: Port/app/v1/adreg’’...
-
Page 12: Access Control Setting
Ethernet and Cloud Server Settings Click on > [ COMM. ] > [ Ethernet ] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface. Click on >... - Page 13 Multi-face Template Identifying Settings Click on > [ System ] > [ Face ] > [Recognition Settings] > [Identifying Mode] > [Multi-face Identifying] to enter the setting interface. When the [Multi-face Identifying] is enabled, the device can perform facial recognition of multiple people at once.
-
Page 14: Cellular Data Network
Cellular Data Network Remove the back cover of the device and insert the SIM card . Then select [Cellular Data Network] on the [Comm.] interface to enter the setting interface. When the mobile network is connected successfully, the initial interface will display the mobile network logo. -
Page 15: Backup Battery
Back-up Battery Remove the back cover of the device and plug the battery back-up wiring port into the battery bay. The back-up battery can provide at least 2 hours of operation for the device without being connected to a power source, and the initial interface battery icon changes from to . - Page 16 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.