Enterasys XSR-3150 Quick Reference Card page 2

Installing NIMs and Rack Mounting
The XSR-3150 provides two NIM card slots. Perform the
following steps to install optional NIM card(s) and rack
mount the XSR. Refer to the XSR Getting Started Guide
for cord attachment directions.
1. Be sure power is off and power cord is disconnected.
2. Place the XSR on a static-free surface and remove the
slot cover by pressing it to the side and pulling it out.
Then, unfasten the screws holding the cover to the
chassis and remove, as shown below.
SECURITY ROUTERS
XSR-3020 NIM1 NIM2
NIM 1 NIM 2 10/100/1000 10/100/1000
VPN 1000
Link
SYS
PWR
COM COM TX GBIC ETH3 ETH1 ETH2
3. Attach the NIM(s) to the connector pins and fasten to
the motherboard with four screws, as shown below.
SECURITY ROUTERS
XSR-3150 NIM1 NIM2
NIM 1 NIM 2 10/100/1000 10/100/1000
VPN 1000
Link
SYS
PWR
COM COM TX GBIC ETH1 ETH2 ETH3
4. Reattach the chassis cover. Optionally, remove the
CompactFlash slot cover, as shown below.
5. Gently insert the CompactFlash memory card in the
slot, as shown below. If the card does not seat easily
but stops halfway into the slot, do not force it in - the
card was inserted incorrectly. Flip it over and re-insert.
6. Attach the rack brackets to the chassis with the screws
supplied, as shown below.
7. Rack mount the bracketed chassis, as shown below.
LEDs
The 14 LEDs on the XSR front panel display system and
port status as described and illustrated below (six system
LEDs at left & eight GigabitEthernet LEDs at right).
NIM1 NIM2
10/100/1000 10/100/1000
VPN 1000
Link
SYS
PWR
COM
TX
GBIC ETH1 ETH2 ETH3
LED State Function
PWR ON XSR powered up, Bootrom initialized
OFF XSR powered down
SYS (tem ON XSR operational
Status)
OFF XSR non-functional due to hardware or
Boot-prom problem
Blinking Flash update in progress (image
downloading), warning you not to power
down, which can leave the XSR without
valid software.
COM Blinking Port transmitting or receiving data
(munica-
OFF Port idle
tion)
VPN ON VPN tunnel up
OFF No VPN tunnel connected
NIM 1, 2 ON NIM card present and power-up
diagnostics test passed
OFF NIM slot empty or power-up diagnostics
test failed
Ethernet Amber only ON 10BaseT link auto-detected
Port 1, 2, 3 Green only ON 100BaseT link auto-detected
Both ON 1000BaseT link auto-detected
Blinking Port is transmitting/receiving data
Fiber/ Both OFF T1/E1, ISDN or HSSI link up
Copper Link LED ON Fiber link up
GBIC Port TX LED Activity on fiber port
Blinking
BRI NIM Switch ISDN BRI-S/T link active & ready for
Port 0, 1 connected traffic. LED located on NIM
ADSL NIM Blinking Line in training (sync with DSLAM)
1 ON Training mode ended, line operational
OFF Line is down
ADSL NIM Blinking Traffic activity in sync with data traffic
2
T3/E3 NIM:
-LOS Red ON Loss of Signal
-LOF Red ON Loss of Frame
-Alarm Amber ON Error condition detected
-Enable Green ON Link is up and running
Copper Link ON 100Base-T link is auto-detected
Ethernet Link OFF 10Base-T link is auto-detected
NIM ACT Blkg Port is transmitting or receiving data
Fiber-optic Link ON 100Base-F link is auto-detected
Ethernet ACT ON Port is transmitting or receiving data
NIM
XSR-3150
Quick Reference Card
Use this card to
quickly install
and connect the
XSR-3150
For complete
configuration
instructions, refer
to the Getting
Started Guide
Note: You can view and download all product
documentation from the Enterasys web site:
http://www.enterasys.com/support/manuals
Enterasys Networks
50 Minuteman Road
Andover, MA 018107
Phone: 978.684.1000
www.enterasys.com
PN 9033871-04