Advertisement
System Overview
Front View
365.3 (SP-6565)
395.8 (SP-6567)
Left Side View
Right Side View
SP-6565 & SP-6567
SP-6565
28.5
Quick Setup
Installing Wall O-ring
Step 1.
Place the Wall O-ring into the groove surrounding the back of
the front bezel.
Step 2.
Install the system onto the wall.
Wall
SP-6565
Step 1. Install the hooks into the mounting holes
on the four sides of SP-6565 using 10 x
M3x5mm screws.
SP-6567
Step 1. Install the hooks into the mounting holes
on the four sides of SP-6567 using 12 x
M3x5mm screws.
Install hooks onto the
four sides of the Panel PC.
The following messages are reminders for safety on how to protect your system from damages and to extend a long life of the system.
1. Check the Cable Voltage
•
The range of operating voltage should be between DC 9V and 36V. Otherwise, the system could be damaged.
2. Environmental Conditions
• Place your SP-6565 / SP-6567 on a sturdy, level surface. Be sure to allow enough space to have easy access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using SP-6565 / SP-6567 when it's been left outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0°C ~ 45°C for SSD.
• Avoid moving the system rapidly from a hot place to a cold place and vice versa because
condensation may come from inside of the system.
• Placing SP-6565 / SP-6567 in strong vigrations may cause hard disk failure.
• Don't place the system close to any radio-active device in case of signal interference.
Rear View (SP-6565)
C.L.100(VESA)
Top View
SP-6567
SP-6565 and SP-6567
The picture below illustrates the top view of SP-6565 and
SP-6567 equipped with the optional Expansion Slot.
28.5
5.5
HDD Easy Maintenance
Step 1.
Pull out HDD tray.
Step 2.
Release the two
Place the Wall
screws of HDD tray.
O-ring into the
groove surrounding
the back of the
Heed the
front bezel.
be directed upwards when
you push back HDD tray.
Installing Memory Heatsink
Memory module
Wall O-ring
Installing Hooks
SP-6565
Step 2. Mount SP-6565 Panel PC equipped
with 10 hooks onto the wall firmly.
SP-6567
Step 2. Mount SP-6567 Panel PC equipped
with 12 hooks onto the wall firmly.
Safety Precaution
Rear View (SP-6567)
C.L.100(VESA)
361.3 (SP-6565) / 395.8 (SP-6567)
357.5 (SP-6565) / 387.5 (SP-6567)
260
CFast
Reset
SIM Card
HDMI
USB
ANT
ANT
ANT
LPT
COM5
COM6
5V/GND/12V
DC OUT
Expansion
Slots (optional)
mark should
Step 3.
Release the four screws
of HDD tray.
Step 1. Attach the adhesive tapes on both sides of the
memory module.
Adhesive tape
click
Step 2. Put the click on to secure.
SP-6565
Step 3. Install 10 mounting brackets onto the hooks
on the four sides of Panel PC and fasten the
mating screws to secure firmly.
SP-6567
Step 3. The operation is the same as above.
Wall
3. Handling
• Avoid putting heavy objects on top of the system.
• Don not turn the system upside down. This may cuase the hard drive to mal-function.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the system.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner for computers.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly recommend that qualified engineers
can open and disassemble the system. Please handle LCD and Touchscreen with extra care as they are easily breakable.
Wall Mount Cut-out Dimensions
SP-6565
SP-6567
360.5
0.3
Wall
Bottom I/O View
For SP-6565 / SP-6567Rx-x0x
LAN1
DC IN
DVI-I COM3
COM1
LAN2
Remote
Remote
DC IN
COM3
COM1
Switch
DVI-I
LAN
Switch
1
Power
COM4
COM2
2
Button
1
DIO
POE ON
2
I2C
DIO
COM4
COM2 PoE1
I
PoE2
For SP-6565 / SP-6567Rx-x1x
LAN1
Power LED
COM3
LAN2
HDD LED
COM1
(PoE optional)
DVI-I
Remote
Switch
COM3
COM1
LAN
DVI-I
Power
1
Button
COM4
DIO
COM2
2
1
POE ON
2
I2C
DC IN 9~36V
Remote
COM4 COM2
DIO
Switch
I2C
(optional)
PoE
(optional)
(optional)
3-pin Terminal
Power
Block DC IN
LED
HDD & Memory & VESA Mount
Accessories
Memory Heatsink
HDD Tray
Screw
Memory Heatsink x 2
M3 x 5 mm Screw x 4
Installing VESA Mount
Hook Accessories (option)
Mounting Brackets
x 10 for SP-6565
x 12 for SP-6567
M3x5mm screw
x 10 for SP-6565
x 12 for SP-6567
x 10 for SP-6565
x 12 for SP-6567
M4x35mm screw
1. Install the bracket.
2. Tighten the screw.
All Rights Reserved. Copyright 2017
(Unit: mm)
390.3
.2
0
Wall
4 x
USB 3.0
USB3.0
Line In
Line Out
Mic In
2
C
USB3.0
Mic In
Line Out
Line In
4 x USB 3.0
VESA Mount
VESA Mount Kit x 1
x 10 for SP-6565
x 12 for SP-6567
Hook
x 10 for SP-6565
x 12 for SP-6567
M4 Nut
Advertisement
