Monitor Panel; To Read A Water Or Sewer Tank Level; To Read The Battery Voltage; Refrigerator - Airstream FLYING CLOUD 2024 Owner's Manual

Monitor Panel

The display is the only system component that the user
accesses� All user input to the display is done using the
buttons along the bottom�
The display receives information from the individual
sender pads via a single, two-conductor wire and
displays the level information in percent of full on a
three-digit LED display� When the front panel button for
a particular tank is pressed, the display powers up and
displays the level for that tank�
Sender pads are installed and stuck to the sides of the
holding tanks� The sender pad scans the level through
the tank wall using digital techniques programmed into
the sender microprocessor�

To Read a Water or Sewer Tank Level

Press and release the button corresponding to the
tank to be checked, and the display will show the
levels in percent on the LED display� If no other button
is pressed, then the display shuts off after about 5
seconds�
If another button (including BATT) is pressed before the
5-second time is up for the first button, the display will
immediately switch to show the new level or voltage�
The 5-second time-out is restarted every time a button
is pressed�
To continuously display a reading, press and release
the desired button, then press the same button again�
The display will be on hold mode when the button
is released, indicated by the decimal point on the
right-hand side� While the display is in hold mode, it
will recheck the level once per second so the user
can watch the level change while the tank is filled or
drained� The display will automatically shut off after 5
minutes in hold mode� To end the hold mode before the
5 minutes is up, press any tank button, and the display
will shut off� By pressing two buttons at once, the
diagnostic functions can be accessed�

To Read the Battery Voltage

Press the BATT button and release it; the display will
show the battery voltage on the LED display� If no other
button is pressed, then the display will shut down after
about 5 seconds�
2024 Flying Cloud
If the BATT button is held down, the display
continuously rechecks the voltage and shows the
updated value. The reading may flicker back and forth
between two values�
If another button is pressed before the 5-second time
is up for the BATT button, the display will immediately
switch to show the value for the new button� The
5-second time-out is restarted every time a button is
pressed�
There is no hold mode for the battery voltage�

Refrigerator

Review all refrigerator literature supplied in your
owner's packet or stored in the refrigerator prior to
operating�
Flying Cloud models have all-electric refrigerators
which feature a strong 12V compressor, no LPG
is required� Depending on your model, to turn the
refrigerator on, touch and release the ON/OFF
button� The blue indicator light will glow solid blue to
indicate that the refrigerator is on, or use the wide
range thermostat designed to sense the evaporator
(cold plate) temperature� The coldest position on
the thermostat is reached by turning the knob to the
right (clockwise); conversely turning the thermostat
knob to the left (counterclockwise) yields a warmer
setting� The OFF position is reached by turning hard
counterclockwise past the click� The reference point is
shown with an indicator sticker beside the knob�
To get ready for a trip, start your refrigerator and let it
cool for eight hours before loading with food� For the
best cooling performance, let air move freely inside the
compartments�
It will be necessary to defrost the refrigerator and
freezer compartment from time to time� Frequency
depends on usage, the number of times the door is
opened and closed, and the humidity level� To defrost,
turn the refrigerator off and prop open the door� Most
of the condensation will run out of the condensate tube
to the outside of the trailer� Use dry towels to keep
extra condensation from dripping onto the floor. Do not
use heat or sharp objects to speed up the defrosting
process as this can damage the unit�
Clean the interior periodically with mild cleaner or
solution of liquid dish detergent and warm water� Rinse
with a solution of baking soda and clean water�
NOTICE
Speeding up the defrost process with a knife
or scraper is strongly discouraged due to the
likelihood of rupturing the refrigerant circuit.
Interior
5-19