Table of Contents
Advertisement
Interior
Shower Stall
To clean your fiberglass (plastic on 23 ft. rear bath)
shower stall unit, use warm water and one of the
stronger liquid detergents� Do not use abrasive
cleaners as they may scratch and dull the surface
of your unit� Stubborn stains can be removed with
solvents such as turpentine, paint thinner, or acetone�
Restore dulled areas by rubbing with an automotive
type liquid cleaner, then, put the soft glow back into
your unit with a light application of liquid wax�
WARNING
Applying wax to the base of the shower floor is
not recommended, as this could create an unsafe
surface.
Shower Head
The shower head is designed to give maximum
flexibility in usage, and provides for water-saving
techniques when using your trailer on self-containment�
It can be held in the hand and moved about the body�
Normally, the best water conservation procedure is to
wet the entire body and then turn the water off� Apply
soap, lather thoroughly, and then rinse the soap off�
Retractable Clothesline
A retractable clothesline is installed for your
convenience in the shower stall� To use, pull the
line from the base and attach it to the holder on the
opposite wall� Turning the nut on the base will tighten
the line�
Dinette
Flying Cloud models have dinettes which can be made
into a bed by raising up on the front of the table and
folding the table leg up against the bottom of the leaf�
As the table is raised, it will unhook from the upper
wall brackets� Once unhooked, the wall hinge will
allow it to be pulled out and lowered on the supports
of the dinette seats� The backrests of the seats are
placed over the table to complete the conversion� It is
recommended to travel with the table in the lowered
position�
On 23 ft� front bed and 30 ft� Bunk models the dinette
table has a telescoping pedestal leg� To lower, release
the black compression clamp lever on the pedestal leg
and push the table down� Once lowered, clamp the
lever back to lock the leg in position� On the bottom of
the table top a latch is installed and can be released
to allow the table top to slide out towards the aisle�
Use the dinettes backrests to cover the table top and
complete the conversion�
5-4
For models with removable pedestal legs, remove the
dinette legs by twisting counterclockwise and store
them� Lift the seat cushions up and out of the way�
Place the tabletop across the gap� There are rubber
stoppers on the bottom of the tabletop to keep it in
place� Position the seat cushions on the outer part of
the bed with the backrests laid in the middle to form a
complete bed�
Desks
The 30FB Office model is equipped with a desk, roller
chair, and convertible bed� When converting the bed,
the desk chair will need to be positioned so that the
pull out bed base does not hit the chair's rollers� Once
the chair is in the correct position, use the strap inside
the right hand cubby, and secure the chair in place
by connecting the strap to the latch, on the left side
of the desk� The bottom drawer, on the left side of the
desk, can be used to support the bed by pulling it out
and flipping the top panel of the bed base over onto
it� To complete the bed conversion, use the cushions
provided, to cover the base�
The 25FB and 27FB models have an optional office
space, which includes a power-lift desk and an
adjustable rolling chair� The desk is controlled from
the switch, mounted under the desk top, on the right-
hand side� The desk can be adjusted, so that it can be
used in an upright (standing) position, or in a seated
position� Installed in the top of the desk is a pop-up
120V receptacle and USB ports for plugging in a
computer and other devices� When using the desk as
a table top, the pop-up outlet can be pushed down and
sealed� The receptacle is completely self-contained
2024 Flying Cloud
Advertisement
Chapters
Table of Contents
