Related Manuals for Lincoln Electric PF 56D
Summary of Contents for Lincoln Electric PF 56D
- Page 1 IM3188 04/2023 REV02 PF 56D OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland www.lincolnelectric.eu...
-
Page 2: Table Of Contents
12/05 THANK YOU! For choosing the QUALITY of the Lincoln Electric products. Please check packaging and equipment for damage. Claims for material damaged in shipment must be notified immediately to the dealer. For ease of use, please enter your product identification data in the table below. Model Name, Code & Serial Number can be found on the machine rating plate. -
Page 3: Technical Specifications
Technical Specifications NAME INDEX PF 56D K14392-1 INPUT Input Voltage U Input Amperes I EMC Class 40Vdc 4Adc RATED OUTPUT Duty Cycle 40°C (based on a 10 min. period) Output Current 100% 420A 500A Welding Current Range Peak Open Circuit Voltage 5 ÷... -
Page 4: Electromagnetic Compatibility (Emc)
If any electromagnetic disturbances are detected the operator must put in place corrective actions to eliminate these disturbances, if necessary with assistance from Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. -
Page 5: Safety
Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or equipment damage. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. - Page 6 WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area and have a fire extinguisher easily accessible. Welding sparks and hot materials from the welding process can easily go through small cracks and openings to adjacent areas. Do not weld on any tanks, drums, containers, or material until the proper steps have been taken to insure that no flammable or toxic vapors will be present.
-
Page 7: Introduction
Introduction PF 56D is digital wire feeder which have been designed to Set of power source and wire feeder allow welding in work with Lincoln Electric power sources: listed processes: GMAW (MIG/MAG), POWER WAVE 350CE, ® FCAW, ... - Page 8 3. Quick Coupling Socket: Coolant inlet (takes Controls and Operational Features warm coolant from the welding gun). WARNING Maximum coolant pressure is 5 bar. 4. Output Socket SMAW welding: For connecting welding cable with an electrode holder. 5. U7 User Interface: See „User Interfaceʺ section. 6.
- Page 9 Loading the Wire Spool Spools of wire with a maximum weight of 16 kg can be used without an adapter. Holder allows mounting plastic, 14 15 steel and fiber spools on the 51mm spindle. It is possible to use other spools after using the appropriate adapter, which can be purchased separately (see "Accessories"...
- Page 10 Proper adjustment of drive rolls. pressure arm gives the best welding performance. Wire Feeders PF 56D is equipped with drive roll WARNING V1.0/V1.2 for steel wire. For others wires and sizes it is If the roll pressure is too weak, the roll will slide on the required to install proper drive rolls kit (see "Accessories"...
- Page 11 Gas Connection Transport and Lifting WARNING WARNING Falling equipment can cause injury and CYLINDER may explode if damaged. damage to unit. Always fix the gas cylinder securely in an upright position, against a cylinder wall rack or purpose-made cylinder cart. ...
- Page 12 We respond to our customers based on the best warranty information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, Any noticeable damage should be reported immediately and assumes no liability, with respect to such information and repaired.
-
Page 13: Weee
12/05 Part List reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine. -
Page 14: Accessories
Accessories OPTIONS & ACCESSORIES K14382-1 WIRE FEEDER DRUM QUICK CONNECTOR K14175-1 GAS FLOW METER KIT K14349-1 TIG ADAPTER C5B K14382-1 ADAPTER TIG ADV-MOD PF56D K10095-1-15M REMOTE CONTROL 6-PINS, 15M K2909-1 6-PIN/12-PIN ADAPTER K14091-1 REMOTE MIG LF 45 PWC300-7M (CS/PP) E/H-400A-70-5M ELECTRODE HOLDER 400A/70MM²... - Page 15 ROLL KIT FOR CORED WIRES KP14150-V12/16R ROLL KIT 1.2/1.6RT FI37 4PCS ORANGE/YELL KP14150-V14/20R ROLL KIT 1.4/2.0RT FI37 4PCS KP14150-V16/24R ROLL KIT 1.6/2.4RT FI37 4PCS YELL/GREY KP14150-V09/11R ROLL KIT 0.9/1.1RT FI37 4PCS KP14150-V10/12R ROLL KIT 1.0/1.2RT FI37 4PCS -/ORANGE WIRE GUIDES 0744-000-318R WIRE GUIDE SET BLUE Ø0.6-1.6 0744-000-319R...
-
Page 16: Connection Diagram
Connection Diagram English English... - Page 17 English English...
- Page 18 English English...