Table of Contents
Advertisement
applications and features that you previously needed a
physical set-top box to access.
You need internet connection and accept the Philips
Terms of Use, the Privacy Policy and Smart TV Terms of
Use to install the M7 TV App. You can install the App
either using the Apps Screen or the Search for satellites
option in the Settings Menu.
If the M7 TV App cannot be downloaded or installed,
you may try to download again later. If problem persists,
please contact M7.
Once the M7 TV App has been installed successfully, you
can start to receive additional commercial channels in HD
and UHD quality. Please switch the source to Watch
Satellite after the installation. If you have been using a
CAM Module for M7 before, continue to use it to
descramble the signal when you are watching a satellite
channel.
After M7 TV App is installed, there are some features will
be affected.
• Recording and reminder functionalities are not allowed
for satellite channels.
• Favourite list is only available in Antenna/Cable.
• The channel selection, TV Guide, channel information
are replaced by the TV App user interface
• Satellite channels renaming and cloning will be
disabled.
* Note: M7 TV App is only available for M7 subscriber of
certain countries only.
5.2. Antenna Installation
Update Channels
Automatic Channel Update
If you receive digital channels, you can set the TV to
automatically update these channels.
Once a day, at 7 AM, the TV updates the channels and
stores new channels. New channels are stored in the
Channels List and are marked with a . Channels
without a signal are removed. The TV must be in standby
to automatically update channels. You can switch off
Automatic Channel Update.
To switch off the automatic update:
1 - Select Settings > Channels & Inputs >
Channels > Antenna/Cable Installation or Antenna
Installation and press OK.
2 - Enter your PIN code if necessary.
3 - Select Automatic Channel Update and press OK.
4 - Select Off and press OK.
5 - Press (left) to go back one step or press Back to
close the menu.
When new channels are found or if channels are
updated or removed, a message is shown at TV start up.
To avoid this message to appear after every channel
update, you can switch it off.
To switch off the message:
1 - Select Settings > Channels & Inputs >
Channels > Antenna/Cable Installation or Antenna
Installation and press OK.
2 - Enter your PIN code if necessary.
3 - Select Channel Update Message and press OK.
4 - Select Off and press OK.
5 - Press (left) to go back one step or press Back to
close the menu.
In certain countries, the Automatic channel update is
done while watching TV or on any moment when the TV
is in standby.
Manual Channel Update
You can always start a channel update yourself.
To start a channel update manually:
1 - Select Settings > Channels & Inputs >
Channels > Antenna/Cable Installation or Antenna
Installation and press OK.
2 - Enter your PIN code if necessary.
3 - Select Search for Channels and press OK.
4 - Select Start and press OK.
5 - Select Update Digital Channels, select Next and
press OK.
6 - Select Start and press OK to update the digital
channels. This can take a few minutes.
7 - Press (left) to go back one step or press Back to
close the menu.
Reinstall Channels
Reinstall All Channels
You can reinstall all channels and leave all other TV
settings untouched.
If a PIN code is set, you will need to enter this code
before you can reinstall channels.
To reinstall channels:
1 - Select Settings > Channels & Inputs >
Channels > Antenna/Cable Installation or Antenna
Installation and press OK.
2 - Enter your PIN code if necessary.
3 - Select Search for Channels and press OK.
4 - Select Start and press OK.
5 - Select Advanced channel reinstall and press OK.
6 - Select the country where you are now and press OK.
7 - Select the type of installation you want, Antenna
(DVB-T) or Cable (DVB-C) and press OK.
8 - Select the type of channels you want, Digital and
15
Advertisement
Table of Contents
