Table of Contents
Advertisement
Available languages
Available languages
QUICK GUIDE
This Quick Guide gives you information about how to install
your robotic lawn mower with a wire installation. If you install
your product with EPOS™ technology without boundary wire,
read the Operator's manual supplied with the Reference
station EPOS™ RS1.
To start the product for the first time
1. Download the Automower® Connect app from App Store or
Google Play.
2. Sign up and specify an e-mail address and a password to
create a Husqvarna account.
3. Log in to your Husqvarna account in the app.
4. Push the jog wheel for 3 seconds to switch on the robotic
lawn mower.
5. Enter the factory PIN code 1234 on the robotic lawn mower.
6. Select My mowers in the Automower® Connect app, and
then select the plus sign (+).
7. Follow the instructions in the app.
A
Placement of and connecting the
charging station
1. Place the charging station at a central position in the work
area, with a lot of open space in front of the charging
station and on a relatively horizontal surface.
2. Attach the top of the charging station.
3. Put the grommet with the cables into position.
4. Connect the cable to the charging station.
5. Connect the power supply's low-voltage cable to the
charging station and the power supply.
6. Connect the power supply to a 100-240 V wall socket.
7. Place the robotic lawn mower in the charging station to
charge the battery while the boundary wire is laid.
B
Placement of the boundary wire and the
guide wire
1. Lay the boundary wire so that it forms a loop around the
working area.
2. Make an eyelet at the point where the guide wire will later
be connected.
3. Run the guide wire to the point on the boundary loop where
the connection will be made. Avoid laying the wire at tight
angles.
C
Connecting the boundary wire and the guide
wire
1. Narrow passages in the yard make it difficult for the robotic
lawn mower to find the charging station. The robotic lawn
mower can be lead to remote areas using the guide wire.
The guide wire also helps the robotic lawn mower to
quickly find the charging station.
2. Lay the guide wire under the charging station and at least
2 m / 7 ft straight out from the front edge of the charging
station.
3. Open the connectors and lay the wire ends in the recesses
on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8"
above the connectors.
6. Press the connectors onto the contact pins, marked AL
(left) and AR (right), on the charging station. It is important
that the right-hand wire is connected to the right-hand
contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the connector to the contact pin marked G1/G2/G3
on the charging station.
D
Connecting the guide wire to the boundary
wire
1. Cut the boundary wire with a wire cutters at the centre of
the eyelet that was made in step B.2.
2. Connect the guide wire to the boundary wire using the
accompanying couplers. Press the couplers completely
together with a polygrip.
Maintenance
•
Set the product to OFF before all work on the robotic lawn
mower's chassis, such as cleaning or replacing the
blades. Replace the blades regularly for the best mowing
result.
•
Never use a high-pressure washer to clean the robotic
lawn mower. Never use solvents for cleaning. Clean the
product with a brush and a water hose.
•
All connections to the charging station (power supply,
boundary and guide wire) must be disconnected if there
is a risk of a thunderstorm.
•
Fully charge the battery at the end of the season before
winter storage.
For more information and instructions,
read the complete Operator's manual in the
Automower®Connect app or on
www.husqvarna.com.
en
Advertisement
Table of Contents
