Sony XAV-AX5000 Service Manual page 4

XAV-AX5000
IMPORTANT NOTE FOR REPLACING THE MAIN BOARD
When the MAIN board is replaced, be sure to perform the follow-
ing works.
• DESTINATION SETTING (Refer to following)
• FLICKER ADJUSTMENT (Refer to page 23)
• COMMUNICATION CHECK OF Apple CarPlay OR Android
Auto (Refer to page 6)
IMPORTANT NOTE FOR REPLACING THE DISPLAY
BOARD
When the DISPLAY board is replaced, be sure to perform the fol-
lowing works.
• FLICKER ADJUSTMENT (Refer to page 23)
• COMMUNICATION CHECK OF Apple CarPlay OR Android
Auto (Refer to page 6)
DESTINATION SETTING
When the MAIN board is replaced, the destination setting is neces-
sary.
Note 1: Remote commander is necessary for setting operation.
Note 2: When discriminating the destination, refer to "MODEL IDENTI-
FICATION" on page 3.
1. Destination Setting
Set destination according to the procedure below.
1-1. Setting the Destination Code
Procedure:
1. Connect the power cord to the regulated DC power supply, and
turn the power on this unit.
2. Press the [HOME] button on the main unit.
[HOME] button
(Displayed screen in the above fi gure are example)
3. Press the [OFF] button on the remote commander to the state
of source off, enter the destination setting mode by pressing
the buttons on the remote commander in order of the [4] t [5]
t [6] (press only the [6] button for two seconds).
(Displayed screen in the above fi gure are example)
4
Regulated DC
power supply
+
–
stand, etc.
4. Since various versions, destination code and BD address
screen are displayed, refer to "1-2. Entering the Destination
Code" and set the destination code.
CPU Version
MCU Version
DSP Version
OSD Version
Destination Code
BD ADDRESS
(Displayed characters/values in the above fi gure are example)
5. Refer to "2. Confi rmation After Destination Setting" on page
5, and confi rm a correct destination was set.
6. Disconnect the power cord from the regulated DC power sup-
ply, and turn the power off this unit.
stand, etc.
7. Complete the destination setting operation.
1-2. Entering the Destination Code
Note 1: The destination code cannot be inputted by operation of main unit.
Be sure to input the destination code by using the remote com-
mander.
Note 2: The number buttons on the remote commander cannot be used.
Operation method:
1. Press the button on the remote commander in order of [
t [ ] t [ENTER], enter the destination setting mode and
.
the left most digit of "Destination code" change to red (cursor
for edit) and blinks.
CPU Version
MCU Version
DSP Version
OSD Version
Destination Code
BD ADDRESS
(Displayed characters/values in the above fi gure are example)
2. Press the [ V ] or [ v ] button on the remote commander, and se-
lect the alphanumeric character of "0 to F".
Refer to "1-3. Destination Code" on page 5 for the destination
code to input.
CPU Version
MCU Version
DSP Version
OSD Version
Destination Code
BD ADDRESS
(Displayed characters/values in the above fi gure are example)
0.15.0
0.15.0
3520
1712011016
0 1 9 4 1 2
xx:xx:xx:xx:xx:xx
Regulated DC
power supply
+
–
>
0.15.0
0.15.0
3520
1712011016
0 1 9 4 1 2
xx:xx:xx:xx:xx:xx
Red blinks
0.15.0
0.15.0
3520
1712011016
1 1 9 4 1 2
xx:xx:xx:xx:xx:xx
Press [V] or [v] button
to select "0 to F".
– Continued on next page –
]
SYS SET