Philips 42PF9630A/37 Manual page 36

-- AV1
F.- _ Pb R
ID,G,+A' II
[{ _ I_'1 I
AUDIO I_
AV,,AV3: [ 'N
L_ ++ +
DVD / STB
DVD Player or other accessory digital source devices
Devices with ComponentVideo Output Connectors (YPbPr)
This TV is capable of displaying 1080i, 720p and 480p DTV signals when
connected to a DTV tuner Set Top Box. Select the output of the Set Top
Box to either 1080i, 720p or 480p.A DTV signal must be available in your
area.
_) Connect the three separate component video cables (_) to the device
having component video outputs (YPbPr), such as Set Top Boxes, DVD-
players, laser-disc players, videogame players, satellite receivers or other
equipment, and to the Y, Pb and Pr jacks of AVI or AV3 on the TV.
, Connect to the Y, Pb and Pr jacks of AVI in case of devices with analog
audio signals.
, Connect to the Y, Pb and Pr jacks of AV3 in case of devices with digital
audio signals.
_) In case of a device with digital audio, connect the audio cable (_) to the
DIGITAL AUDIO OUT of the device and to the DIG.AUDIO IN of the iV
or to your Home Cinema system.
In case of a device with analog audio, connect the audio cable to the
device's AUDIO L and R (_) jacks and the L and R audio jacks of AVI.
AVl :
Devices with RGB output
O Connect the device with RGB output with separate Horizontal and Vertical
sync to the Pr/R Pb/BY/G input (_) jacks and to the H and V jacks of AVI
®.
O Connect the audio cables to the L and R AUDIO jacks of AVI (]_).
DVD / STB
I1<+
I1(+_ <_;/__J I
AV2 --
/®- 1
AV1/AV2 :
L+R
DVD STB
Devices with an S-Video connector
Connect an S-Video cable to the AVI or AV2 S-VIDEO input (_).
Note: When using the S-VIDEO connector do not connect any @vice to the AV
VIDEO input that you are usin_
Connect the audio cables to the device's AUDIO L and R jacks and to the
L and R audio AV1 or AV2 jacks (_ on the TV accordingly to where you
connected the S-Video cable.
Notes
- If necessary, y ou can adjust the picture position to the centerof the semenwith the
cursorkeys.
- The labelsfor the componentvideo socketsmay dialerdependingon the DVD
player or the device connected. A lthoughthe abbreviationsmay vary,the lettem B
and R stand for the blue and md componentsignals,respectively, a nd Y indicates
the luminancesignal./Refer t o the DVD player'sor @vicesinstructionsfor use for
@finitions and connectiondetails.
- Thistelevisionis @signedto accept high @finition signalstandards 480p, 720p and
1080i as specifiedby the ElectronicIndustries Associationstandard EIA770.3.
Digital devicesfrom different rnanufactummhave the possibilityof cliffbring output
standards which may causedifficulties for the televisionto properly display
- Due to possibledigital image distortion when displayingsignalsfrom connected
digital equipment,automaticallythe Auto picture setting Soft is selected,if you
selected Digital STBin the Sourcemenu.SeePicturemenu,Auto picture,p. 19.
Changingthis settingduring reviewingwill not be stored as Personal setting after
switch off
Warning: in case you notice scrolling images, wrong colors or no color; no picture, or
even combinations of these on your semen, check if the connections are done in the
correct way or move your digital device further away from your TV
34