Related Manuals for Zenty ZT-118
Summary of Contents for Zenty ZT-118
- Page 1 Zenty | Professional A/V Solution Provider ® ZENTY 9807 EMILY LANE STAFFORD, TX 77477 (844) 200-1945 SUPPORT@ZENTY.COM (844) 200-1945 | sales@zenty.com Page 1 of 33 Copyright © Zenty AV...
- Page 2 This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. (844) 200-1945 | sales@zenty.com Page 2 of 33 Copyright © Zenty AV...
- Page 3 (844) 200-1945 | sales@zenty.com Page 3 of 33 Copyright © Zenty AV...
- Page 4 (844) 200-1945 | sales@zenty.com Page 4 of 33 Copyright © Zenty AV...
- Page 5 -10 to +60°C (-14 to +140 °F) Operating Humidity Range 5 to 90 % RH (no condensation) Input Video Signal 0.5-1.0 volts p-p Input DDC Signal 5 volts p-p (TTL) Bandwidth 18Gbit/s (844) 200-1945 | sales@zenty.com Page 5 of 33 Copyright © Zenty AV...
- Page 6 PCM, Dolby5.1, DTS5.1 digital audio Maximum Transmission Distance 1080P 70m/230ft. | 4K 40m/131ft. Power Consumption 68 watts (Max.) Dimensions L438 x W394 x H44 mm Mass (Main Unit) 3kg/6.6lbs (844) 200-1945 | sales@zenty.com Page 6 of 33 Copyright © Zenty AV...
- Page 7 (844) 200-1945 | sales@zenty.com Page 7 of 33 Copyright © Zenty AV...
- Page 8 (844) 200-1945 | sales@zenty.com Page 8 of 33 Copyright © Zenty AV...
- Page 9 1 x 4 ~ 4 x 1, which can switch any input. Signal to 1 channel output or all channel output. The specific operation as follows: (844) 200-1945 | sales@zenty.com Page 9 of 33 Copyright © Zenty AV...
- Page 10 For Example: Output port 2 switch to input 1 Operation: Press OUT number "2" + IN number "1" to complete the switch The video interface has two sub menus: 1. Video Routing 2. Video On/Off (844) 200-1945 | sales@zenty.com Page 10 of 33 Copyright © Zenty AV...
- Page 11 ② Then use “UP””DOWN”button to select“Switching” ③ Press“ENTER”enter next page ④ Press “UP””DOWN”button to select the output（The fifth port means ALL） ⑤ Press“ENTER” ⑥ Press “UP””DOWN”to select the input ⑦ Press“ENTER”，Switch Done (844) 200-1945 | sales@zenty.com Page 11 of 33 Copyright © Zenty AV...
- Page 12 ⑥ Press “UP””DOWN”to select “On”or “Off” ⑦ Press“ENTER”，Switch Done The Audio Control have three sub menus: 1. Line Out 2. Audio Embed 3. Audio De-Embed The specific operation is as follows: (844) 200-1945 | sales@zenty.com Page 12 of 33 Copyright © Zenty AV...
- Page 13 You can select any input to embed 3. Audio De-Embed You can set the output audio (analog audio and coaxial audio) at the same time. You can choose a certain audio output or mute (844) 200-1945 | sales@zenty.com Page 13 of 33 Copyright © Zenty AV...
- Page 14 FXN1234 Default3 4K30 444-LPCM: 2.0 Default4 1080P60 444-LPCM: 2.0 FXN1234 FXN1234 EDID Mode can set each input’s EDID. Includes: Default EDID; User EDID; Copy EDID; Copy HDBT EDID. (844) 200-1945 | sales@zenty.com Page 14 of 33 Copyright © Zenty AV...
- Page 15 The PRESET interface can save the current video, audio, EDID, system Settings, etc., and supports 8 different scenes. Scenes can be modified and cleared through web pages, commands, and panels. The default preset is consistent with factory Settings (844) 200-1945 | sales@zenty.com Page 15 of 33 Copyright © Zenty AV...
- Page 16 SETUP mode can set the device’s RS-232 baud rate, POC Switch, DHCP, Reboot, Factory Specific operations are as follows (844) 200-1945 | sales@zenty.com Page 16 of 33 Copyright © Zenty AV...
- Page 17 On means Dynamic; Off means Static ① Select“Setup”in the menu and press“ENTER” ② Then use “UP””DOWN”button to select the “DHCP”and press “ENTER” ③ Press “UP””DOWN”button to select“On”or“Off”and press “ENTER”to confirm (844) 200-1945 | sales@zenty.com Page 17 of 33 Copyright © Zenty AV...
- Page 18 The POC interface can select a certain HDBT output switch to control POC power supply, and the default POC is "On" Factory Run: Reset Video, Audio, EDID, Setup setting, Preset, Device name. Factory User: Reset Video, Audio, EDID, Setup setting. (844) 200-1945 | sales@zenty.com Page 18 of 33 Copyright © Zenty AV...
- Page 19 Check the device information: IP or System information (844) 200-1945 | sales@zenty.com Page 19 of 33 Copyright © Zenty AV...
- Page 20 HDMI audio output supports uncompressed audio PCM, compressed audio Dolby and DTS, with a maximum support of 7.1 sound channels and a maximum sampling rate of 192KHz. Analog audio supports PCM 2.0 channel. S/PDIF audio supports Dolby or DTS, 5.1 channel. (844) 200-1945 | sales@zenty.com Page 20 of 33 Copyright © Zenty AV...
- Page 21 The matrix can pass the IR signal through the IR system to the HDMI source or pass the IR signal from the HDMI source to the HDMI sink (844) 200-1945 | sales@zenty.com Page 21 of 33 Copyright © Zenty AV...
- Page 22 Double-click the software in the installation package to run specifically (as shown in figure 1 below) and install the RS232 software on the computer. Enter the main interface of the software, as shown in the figure below. (844) 200-1945 | sales@zenty.com Page 22 of 33 Copyright © Zenty AV...
- Page 23 2. The “_” in the commands cannot omit. Parameter: %d: 0 means ALL. 3. Command head & Parameter1 & Parameter2... need to add one “SPACE”. The following table is only an example. Please refer to the list of instructions. (844) 200-1945 | sales@zenty.com Page 23 of 33 Copyright © Zenty AV...
- Page 24 6). Select Use the following IP Address for static IP addressing and fill in the details. For TCP/IPv4 you can use any IP address in the range 192.168.1.1 to 192.168.1.255 (excluding 192.168.1.168). (844) 200-1945 | sales@zenty.com Page 24 of 33 Copyright © Zenty AV...
- Page 25 7). Click OK. 8). Click Close. Default IP Address: 192.168.1.168 MASK: 255.255.255.0 Gateway:192.168.1.1 MAC:0008-DCCA-CF3F Enter the default IP address of the matrix: 192.168.1.168 Account: admin Password: admin (844) 200-1945 | sales@zenty.com Page 25 of 33 Copyright © Zenty AV...
- Page 26 When the HDMI/HDBT Audio output is turned off, displayed as "×", and when the HDMI/HDBT Audio output is turned on, displayed as "√". 6. POC (Remote): “ON” “OFF” means POC turned on or off 7. HTML Version: Current WEB Version (844) 200-1945 | sales@zenty.com Page 26 of 33 Copyright © Zenty AV...
- Page 27 Noted: Double Click the Rename column can change the name of the ports. (844) 200-1945 | sales@zenty.com Page 27 of 33 Copyright © Zenty AV...
- Page 28 (844) 200-1945 | sales@zenty.com Page 28 of 33 Copyright © Zenty AV...
- Page 29 Open the software UART_ISP_V1.6.exe on PC, select the correct port and baud rate 115200, enter "A1" in Port, then select the path of the program in PATH (XXX. Bin), and click UPDATA to complete the upgrade (844) 200-1945 | sales@zenty.com Page 29 of 33 Copyright © Zenty AV...
- Page 30 Open the software UART_ISP_V1.6.exe on PC, select the correct port and baud rate 115200, enter "F0" in Port, then select the path of the program (XXX. HTML) in PATH, and click UPDATA to complete the upgrade (844) 200-1945 | sales@zenty.com Page 30 of 33 Copyright © Zenty AV...
- Page 31 When shipping the unit, carefully pack and send it prepaid, adequately insured, and preferably in the original carton. Include a letter detailing the complaint and provide a day time phone and/or email address where you can be reached. (844) 200-1945 | sales@zenty.com Page 31 of 33 Copyright © Zenty AV...
- Page 32 The items listed are not exclusive, but are for illustration only.) PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY. (844) 200-1945 | sales@zenty.com Page 32 of 33 Copyright © Zenty AV...
- Page 33 WWW.ZENTY.COM 9807 EMILY LANE STAFFORD, TX 77477 (844) 200-1945 SUPPORT@ZENTY.COM SALES@ZENTY.COM (844) 200-1945 | sales@zenty.com Page 33 of 33 Copyright © Zenty AV...