Table of Contents
Advertisement
SPECIFICATIONS
Amplifier Section
[POWER AMP INI
Continuous
average
power
output
of 100
watts* per channel, min., at 8 ohms, from 20
Hz to 20,000 Hz with no more than 0.005% * *
total harmonic distortion (front); 30 watts* per
channel, min., at 8 ohms, from 20 Hz to 20,000
Hz with no more than 0.08% * * total harmonic
distortion (surround); 30 watts*, min., at 8
ohms, from 20 Hz to 20,000 Hz with no more
than
0.08%**
total
harmonic
distortion
(center).
Dynamic power (2 0/4 2/8 9) ..scecscseseesseees 250 W/220 W/150 W
Audio section
Signal to noise ratio (IHF,
A network, shorted)
BONO tecanvag ccstissqsnaisaitingsvuadesssdarsusesevidesstetersveevees
tasters 83 dB
VCR 1, VCR 2, VCR 3, VDP, TV, VIDEO 1, VIDEO 2,
TAPE 1/DAT 1, TAPE 2/DAT 2, LINE, CD, TUNER............ 98 dB
Signal-to- noise ratio [EIA, at 1 W (1 kHz)]
PHONO ..
VCR 1, VCR
2,
VCR 3, VDP, TV, VIDEO
1, VIDEO 2,
TAPE 1/DAT 1, TAPE 2/DAT 2, LINE, CD, TUNER.
Damping factor (1 kHz, 8Q)
Input (sensitivity/impedance)
PHONO se csssiliceressvivsssectanee poscacnacema
ttt eaes 2.5 mV/50 kQ
VCR 1, VCR 2, VCR 3, VDP, TV, VIDEO 1, VIDEO 2, TAPE 1/
DAT 1, TAPE 2/DAT 2, LINE, CD, TUNER
150 mV/30 kQ
80 dB
100 or more
POWER AMP IN .......... een
1 V/50 ko
Phono overload level (T.H.D. 0.1%, 1 kHz)
+ 150 mV
Frequency response
PHONO {RIAA equalization) ...........0+ 20 Hz to 20 kHz, +0.3 dB
VCR 1, VCR 2, VCR 3, VDP, TV, VIDEO 1, VIDEO 2, TAPE 1/0AT
1, TAPE 2/DAT 2, LINE, CD, TUNER......
5 Hz to 100 kHz, £$ dB
Output (level/impedance)
TAPE 1/DAT 1, TAPE 2/DAT 2 REC..
VCR 1, VCR 2, VCR 3 AUDIO OUT
PRE AMP OUT..
Tone control
+ 150 mV/2.7 kQ
150 mV/2.7 kQ
1 V/2200
VCR NOISE FILTER
100 Hz, 5 kHz, — 3 dB
Muting
Loudness Contour... cseeseeseenee
100 Hz/+6 dB, 10 kHz/+3 dB
Video section
[Base band terminals]
Input (sensitivity/impedance)
VCR 1, VCR 2, VCR 3, VDP, TV, VIDEO 1, VIDEO 2,
VIDEO ADAPTOR
v......ccecsesseseecssteeseneeesesateeesenees 1 Vp-p/750
Output {level/impedance)
VCR 1, VCR 2, VCR 3, VIDEO ADAPTOR, TO MONITOR TV 1,
TO MONITOR TV 2....cccessscceeecsecenaeegeesseeeineseaees 1 Vp-p/750
Frequency response
VCR 1, VCR 2, VCR 3, VDP, TV, VIDEO
1, VIDEO 2,
VIDEO ADAPTOR (to TO MONITOR TV 1, 2) 10 Hz to 10 MHz, +$4B
DG/DP
2% 42°
Signal-to-noise ratio
. 58 dB
Cross. talks ecsaasiaccdsiiegesddda cincacaveatcasticsusieates 55 dB (3.58 MHz)
[S terminals]
Input (sensitivity/impedance}
VER 1g 2e: VDP. ccstadetecs
sites cdansees Luminance signal: 1 Vp-p/752
Color difference signal: 0.286 Vp-p/752
Output (level/impedance)
VCR 1, 2, TO MONITOR TV......... Luminance signal: 1 Vp-p/750
,
Color difference signal: 0.286 Vp-p/750
Frequency response
Luminance signal ......ccssseeceeseeseeeee 10 Hz to 10 MHz, *3.4B
Signal-to-noise ratio
Luminance signal...
Cross talk
. 55 dB
55 dB (3.58 MHz)
Surround section
Input (sensitivity/impedance)
REAR, CENTER (POWER AMP IN)..........sseceesscseeseenee 1 V/50 kQ
Output (level/impedance)
REAR, CENTER (PRE AMP OUT)......ccccccccccceseseesseeeee 1 V/4700
Frequency response (at DOLBY PRO LOGIC SURROUND)
VDP to REAR SPEAKERS
+ 20 Hz to 6 kHz, +3 dB
Miscellaneous
Power requirements
U.S. model
Other destination models .
AC 120 V, 60 Hz
AC 110/120 - 127/220/240 V
(switchable), 50/60 Hz
AC outlets
U.S. MOdEl.eeceereee
SWITCHED x 3: TOTAL 300 W MAX
UNSWITCHED
x 1: 200 W MAX
Other destination models ... SWITCHED x 2: TOTAL 300 W MAX
UNSWITCHED x 1: 200 W MAX
Power consumption
U.S. model
Other destination
models .
In standby condition
300 W (UL)
800 W
we
SW
420 (W) x 162 (H) x 421 (D) mm
Dimensions .......
32 (W) x 6-3/8 (H) x 16-9/16 (D) in
Weight (without package) ...........cccceeree teres 12.5 kg (27 Ib 9 02)
Furnished parts
Dry cell batteries ..
Remote control unit .
Template ........666.
Operating instructions .
Connection cords (U.S. model only)
Audio/video cord
Video cord
Audio cord (stereo-mono)
NOTE:
Specifications and design are subject to change without notice due to
improvements.
sepon
*
CLEANING
Ordinarily, use a soft cloth to wipe the exterior.
lf very dirty, dissolve a neutral dish cleaning fluid in water, moisten a
soft cloth with the solution, wring out the cloth to remove excess liquid,
and
wipe away
dirt. Never use
alcohol,
paint thinner,
benzene,
insecticides, or other solvents or sprays on this unit. The surface legends
and finish may be damaged. Read instructions carefully before using
treated dust cloths.
33
<ARB1177>
Advertisement
Table of Contents
