Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SYSFORM HP520
Summary of Contents for SYSFORM HP520
- Page 1 HP520 Hydraulic Guillotine Operation Manual Revision :21/01/22...
-
Page 3: Table Of Contents
Index 1. Safety Rules …………………………………………………………………………………………………………………… 2. Specifications …………………………………………………………………….……………..…………………………… 3. Name Plate ……………………………………………………………………………….……………………………………. 4. Accessories ……………………………………………………………………………………………………………………. 5. Installation of The Back Table …………..………………………………..………………………………. 6. Key Components ……………………………………………………………………….…………………………………. 7. Control Panel And Function Keys ……………………………………..………..………..……………..8. Reset The Back Gauge …………………………………………………………….……………………..……… 9. Cutting Procedure …………………………………………………………………………….…………………………... -
Page 4: Safety Rules
1. Safety Rules The machine has many safety features which make it a safe to operate. Regardless of your experience, safety instructions must be read carefully, completely understood, and applied to your daily work habits. If you do not understand or are confused by certain safety instructions presented in this manual, discuss them with your supervisor. - Page 5 equipment, power must be shut off to adjustments while it is running. all circuits before any work is attempted. Individual switches must be opened and the equipment circuits tested to make sure there is no power. 7. Be sure all operators are aware of all 7.
-
Page 6: Specifications
2. Specifications Specification HP520 Cutting Width 20.47” / 520mm Cutting Height 3.15” / 80mm Narrow Cut 0.59” / 15mm Power Supply 220V 50/60Hz 20A Dimensions (H x W x D) 55.12” x 37.4” x 49.41” 1400 x 950 x 1255mm Weight 903.9 lbs / 410Kg... -
Page 7: Accessories
4. Accessories 4.1 Blade Replacement Tool. 4.2 Tool Set. 4.3 Jogging Block. 4.4 Operation Manual. -
Page 8: Installation Of The Back Table
5. Installation of The Back Table Two people are needed to install the back table. 5.1 Use two hands to pull the back table up and hold it horizontally. 5.2 Use two bars marked R or L to support the back table on the machine horizontally. -
Page 9: Key Components
6. Key Components Touch Safety Beam Blade 2-Hand Switch Switch 2-Hand Switch Side Table Pressure (Option) Power Gauge Switch Hand Wheel Normal Clamping Cutting/Ch Pressure ange Blade Adjustor Switch Manual Clamping Pedal... -
Page 10: Control Panel And Function Keys
7. Control Panel and Function Keys Function Key Function UP/Back Gauge Home Down/Forward Stop/Exit Start/Run Clear the figure on display Program Repeat Cut... - Page 11 Calculator Eject after cut Cutting Depth and Cutting Length Calibration...
-
Page 12: Reset The Back Gauge
8. Reset The Back Gauge 8.1 While Machine is Off 8.1.1 Switch main power clockwise to on ”I”. 8.1.2 Insert the key into key switch. 8.1.3 Switch the key switch to on. 8.1.4 Press to reset the back gauge to home position. 8.2 While Machine is Under Operation 8.2.1 Press to reset the back gauge to home position. -
Page 13: Eject After Cut
9.2.3 Press to set repeat cut enable. 9.3.4 Press 2-Hand to do cutting until the sheet pile is fully cut, after cut the back gauge will go to next position automatically. 9.2.5 After 1 batch has been cut, the Back gauge will go back to 45cm position for batch cut. -
Page 14: Select A Defined Job
9.4.4 Click on 1 cut box then key in cutting length then press 9.4.5 Click on 2 cut box then key in cutting length then press 9.4.6 Click on 3 cut box then key in cutting length then press 9.4.7 Press to let the job start from 1 cut. -
Page 15: Editing And Existing Job
available. 9.5.6 Press to run the job. 9.5.7 Press to exit. 9.6 Editing an Existing Job 9.6.1 Press to get into program mode. 9.6.2 Click on the job No. box 9.6.3 Enter the job No. then press 9.6.4 Press to clear all data in the group. 9.6.5 Press to select the page which needs to be changed. -
Page 16: Cutting Depth
9.6.9 Press to exit. 9.7 Cutting Depth 9.7.1 Press to get into settings. 9.7.2 Press to set cutting depth. 9.7.3 Click on the box and enter the desired value then press Each movement will be 0.3mm. The figure is bigger and the cutting depth is deeper. -
Page 17: Calculator
9.10 Calculator In manual cut mode, a desired cutting length can be get from the calculator and shows on the input box. 9.10.1 Press to get into calculator. 9.10.2 Press after calculating, the value will show on the input box in the manual cut mode. -
Page 18: Trouble Shooting Guide
10. Trouble Shooting Guide 10.1 No Display Reset the circuit breaker below the main power switch. 10.2 Cutter No Function Reset the circuit breaker below the main power switch. 10.3 Clamp No Function Reset the circuit breaker below the main power switch. 11. -
Page 19: Cutting Blade Replacement
the clamping pressure. After adjusting, try to clamp and read the pressure value from the pressure gauge. Usually the clamping pressure range is 6-12MPa. 12. Cutting Blade Replacement Cam Screws Screw #5 Screw#1 Screw #3 Screw #4 Screw #2 12.1 Press to get into settings. - Page 20 12.7 Remove screw #1, #3 and #5. 12.8 Loosen the blade replacement holder screw a bit then remove the blade from blade carrier. 12.9 Install a new blade onto blade replacement holder and fastening the hand screw onto the blade mounting hole #2 and #4. 12.10 Install new blade onto blade carrier and fasten it tight and secure.
-
Page 21: Cutting Stick Replacement
13.Cutting Stick Replacement 13.1 While blade is on home position, switch main power to off. 13.2 Use one hand to push the handle then use another hand to take away the cutting stick. 13.3 Turn the cutting stick around, the cutting stick can be used 8 times, each surface can use 2 times.
Need help?
Do you have a question about the HP520 and is the answer not in the manual?
Questions and answers