Advertisement
K. Wild Card
The wild card feature ( ✱ 1) is used to allow or restrict numbers 0-9 in that digit specified. For example, to restrict numbers 800, 810, 820, 830... simply pro-
gram the TR-1 with 8 ✱ 1 0 # + memory location. Note: With a ✱ or # as the 1st digit, the following six digits can NOT be a wild card ( ✱ 1).
L. Programming a ✱ or a #
Since the TR-1 uses ✱ and # for specific programming functions, you must enter ✱✱ to input a single ✱ and ✱# to input a single # into the dialing string you
wish to allow or restrict. Note: A ✱ or # can NOT be programmed as the second digit, due to conflicts with the security and bypass codes.
M. Allow All Other/Restrict All Other Numbers
Allow all other numbers: Enter ✱4 in programming.
Note: The TR-1 is factory set to allow all other numbers that are not programmed into the Allow/Restrict Table or covered by switches 1-5.
N. Entering Programming Without a Security Code
This mode is useful if you have forgotten your security code and need to enter programming. Set switches 1 and 2
to OFF, and set switch 7 to ON as shown in the diagram to the right. Have someone call the phone connected to the
TR-1. Answer and enter ✱ followed by ANY six digits. Two beeps should be heard indicating you have entered the
programming mode. Enter your new security code (six digits + #47) and any other programming needed, then hang-
up and place the switches back to their original positions.
O. Turning On/Off the TR-1
Turn on the TR-1: Enter ✱9 in programming.
P. Programming Features Quick Reference
Note:The User Programmable Allow/Restrict table can be set to Allow OR Restrict, NOT both simultaneously.
Features
Programmable Allow/Restrict table (factory cleared) .................................................................................................
Clear a number in the Allow/Restrict table .................................................................................................................
Set all programming to factory default .......................................................................................................................
Set jumpers to factory default ....................................................................................................................................
Clear the entire allow/restrict table (positions 00 - 39) ...............................................................................................
Security code (factory set to 845464) ........................................................................................................................
Call timer (01 - 99 in 30 second increments, factory disabled) ...................................................................................
Maximum number of digits allowed to dial (01 - 99, factory disabled) ........................................................................
Bypass code (factory set to 123456) .........................................................................................................................
Clear the entire Ignore table (positions 60 - 71) .........................................................................................................
Programmable Ignore table (factory cleared) ............................................................................................................
Clear a number in the Ignore table ............................................................................................................................
Entering a single Touch Tone
Entering a single Touch Tone # ..................................................................................................................................
Clear all numbers programmed in switch 6 ...............................................................................................................
Allow toll-free numbers 800, 822, 833, 844, 855, 866, 877, 888 (factory setting) ......................................................
Restrict toll-free numbers 800, 822, 833, 844, 855, 866, 877, 888 ............................................................................
Entering a single digit Wild card ................................................................................................................................
Set user programmable table to Allow .......................................................................................................................
Set user programmable table to Restrict (factory setting) ..........................................................................................
Allow all other numbers (factory setting) ....................................................................................................................
Restrict all other numbers .........................................................................................................................................
Activate call timer on outbound calls only (factory setting) ........................................................................................
Activate call timer on inbound and outbound calls .....................................................................................................
Turn the TR-1 off .......................................................................................................................................................
Turn the TR-1 on (factory setting) ..............................................................................................................................
Jumper 6 PABX line access numbers (factory set to 9) .............................................................................................
P
r
o
g
r
a
m
m
i
n
g
P
r
o
g
r
a
m
m
i
n
g
To complete these examples, you must start by following steps 1-3:
1. Call the phone connected to the TR-1 on a C.O. line or analog PABX/KSU station.
2. Answer the phone connected to the TR-1. The following programming can be done by the calling phone or the phone connected to the TR-1.
3. Enter a ✱ followed by the six-digit security code (factory set to 845464), a double beep should be heard.
A. Programming the TR-1 to Restrict All Outbound Calls,
Including 1-800 Calls
4. Enter ✱3 (a double beep should be heard) ✱5 (a double beep
should be heard).
5. Enter ✱08 (a double beep should be heard).
6. Hang-up.
B. Programming a New Security Code of 123456 and a Bypass
Code of 654321
4. Enter 123456#47 (a double beep should be heard).
5. Enter 654321#50 (a double beep should be heard).
6. Hang-up.
C. Using the Wild Card Feature to Allow Only 700, 710, 720, 730,
740, 750, 760, 770, 780 and 790 Numbers in Location 26
4. Enter ✱2 (a double beep should be heard) ✱5 (a double beep
should be heard).
5. Enter 7✱10#26 (a double beep should be heard).
6. Hang-up.
Note: With the TR-1 turned OFF, all dialing will be unrestricted.
.................................................................................................................................
✱
E
x
a
m
p
l
e
s
E
x
a
m
p
l
e
s
Restrict all other numbers: Enter ✱5 in programming.
Turn off the TR-1: Enter ✱8 in programming.
D. Programming the TR-1 with a Maximum Call Length of 10
Minutes for Inbound and Outbound Calls and the Capability of
Dialing Only 7 Digit Numbers
4. Enter 20#48 (a double beep should be heard).
5. Enter 07#49 (a double beep should be heard).
6. Enter ✱7 (a double beep should be heard).
7. Hang-up.
E. Programming the TR-1 to Allow 1-715, 1-612 and 1-414 Area
Codes and Restrict All Other Numbers
4. Enter ✱2 (a double beep should be heard) ✱5 (a double beep
should be heard).
5. Enter 1715#00 (a double beep should be heard).
6. Enter 1612#01 (a double beep should be heard).
7. Enter 1414#02 (a double beep should be heard).
8. Hang-up.
Note: When programming the TR-1, it is not necessary to hang-up and re-
enter programming to program the next memory location. All user pro-
gramming can be done consecutively.
Internal View
of the TR-1
ON
S1
1
2
3
4
5
6
7
S1
ON
ON
OFF
1
2
3
4
5
6
7
Memory
Digits
+ Location
1 - 12 digits ......
+ #00 to #39
(none) ..............
+ #00 to #39
(none) ..............
+ #44
(none) ..............
+ #45
(none) ..............
+ #46
6 digits .............
+ #47
2 digits .............
+ #48
2 digits .............
+ #49
6 digits .............
+ #50
(none) ..............
+ #51
1 - 12 digits ......
+ #60 to #71
(none) ..............
+ #60 to #71
✱✱
#
✱
06
✱
07
✱
08
✱
1
✱
2
✱
3
✱
4
✱
5
✱
6
✱
7
✱
8
✱
9
✱
1-8 digits + ## + 6 + position 1-8
J2
J1
Advertisement
