Viking K-1900-7 Technical Practice page 3

P r o g r a m m
P r o g r a m m
A. Security Code
A six digit number may be used to access the programming mode. The security code has been factory set to 845464 (V-I-K-I-N-
G). It is recommended that you change the security code to a personal 6 digit number as follows:
Step 1. Access programming as shown in section B.
Step 2. Enter your new security code followed by #47.
Step 3. To exit programming simply hang up the K-1900-7.
Note: The security code must be six digits in length and MUST NOT contain a , or #. If you have forgotten your security code,
see section "B, 2. Programming Without Using the Security Code."
B. Accessing the Programming Mode
1. Remote Programming
Step 1. Connect the green and red wires on the K-1900-7 to a C.O. line or analog PABX/KSU station.
Step 2. From a Touch Tone phone, call the line connected to the K-1900-7.
Step 3. Take the K-1900-7 off-hook (remove handset from the cradle). From the calling phone enter "
digit security code, factory set to 845464 (see section A above). A double beep will indicate that programming has
been entered.
Step 4. Program as shown in sections D - I.
Step 5. To exit programming, hang up both phones.
2. Programming Without Using the Security Code
Step 1. Connect the green and red wires on the K-1900-7 to a C.O. line or analog PABX/KSU station.
Step 2. K-1900-7: Place JP1 on pins 1 & 2 (see section C), K-1900-7-EWP: Set DIP switch 1 to ON.
Step 3. From a Touch Tone phone, call the line connected to the K-1900-7.
Step 4. Take the K-1900-7 off-hook (remove handset from cradle). A double beep should be heard indicating you have
entered programming.
Step 5. Program from calling phone as shown in sections D - I.
Step 6. K-1900-7: Place JP1 back on pins 2 & 3 (see section C), K-1900-7-EWP: Set DIP switch 1 back to OFF.
Step 7. To exit programming, simply hang-up the phones.
C. JP1 / DIP Switch Programming
DIP Switch
JP1
(K-1900-7) (K-1900-7-EWP)
1 - ON
Pins 1&2
1 - OFF
Pins 2&3
Note: DIP switch 2 on the K-1900-7-EWP is not used
and should remain in the OFF position.
D. Programming Features Quick Reference
Speed dial number .................................................................................................................
, (anywhere in the speed dial number) .................................................................................
# (anywhere in the speed dial number) ..................................................................................
Set dialing speed to normal (Touch Tones: 120ms on/off, Pulse: 10 pps) (factory setting) .....
Set dialing speed to fast (Touch Tones: 50ms on/off, Pulse: 20 pps) ......................................
Block hand held pocket dialers (factory setting) ....................................................................
Allow hand held pocket dialers ..............................................................................................
Normal pre-dial pause (approximately 1.4 sec) (factory setting) ............................................
Short pre-dial pause (approximately 800 ms) ........................................................................
To add a one second pause at any point in the dialing string .................................................
To add a four second pause at any point in the dialing string .................................................
Toggle between Pulse and Touch Tone dialing (see section I) ...............................................
Change security code ............................................................................................................
To clear the speed dial number and return all programming to factory settings .....................
Note: Special features such as a ,, a #, a mode change and a pause, use single digits in the programming memory.
i n g
i n g
Description
Learn Mode
Normal Operation
(factory setting)
Internal View of
the K-1900-7
JP1
1 2 3
ON
JP1
1 2 3
1 2 3
OFF
Enter Digits
1-32 digit (0-9)
,,
, #
, 1
, 2
, 3
, 4
,
5
,
6
#7
, 7
, 8
6 digits (0-9)
###
,
" followed by the six
Internal View of
the K-1900-7-EWP
DIP
Switches
OFF ON
Memory
Location
- then -
+ # 00
+ #47