Page 1
Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website.
Page 2
Notes on the AC Power Cord AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer.
Remote Control ...11 Replacing the Battery ...12 Remote Control Operation ... 13 Installation ...14 Connecting the Projector...14 Powering On/Off the Projector ...15 Adjusting the Projector ...16 Menu Operation ...18 Maintenance... 22 Cleaning the Lens ...22 Cleaning the Projector Housing ...22 Replacing the Lamp ...23...
The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law. ViewSonic PJD6210/PJD6210-WH...
0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight. ViewSonic Proposed Maximum Concentration 0.1% 0.1% 0.01% 0.1% 0.1% 0.1% Actual Concentration < 0.1% < 0.1% < 0.01% < 0.1% < 0.1% < 0.1% PJD6210/PJD6210-WH...
To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic® Wizard CD-ROM also provides an opportunity for you to print the registration form, which you may mail or fax to ViewSonic. Product Name:...
Introduction Projector Features The projector integrates high-performance optical engine projection and a user - friendly design to deliver high reliability and ease of use. The projector offers the following features: Single chip 0.55" Texas Instruments DLP XGA (1024 x 768 pixels) Auto image re-sizing (Auto-Sync.) to 1024 x 768 full screen with scaling...
Package Contents When you unpack the projector, make sure you have all these components: Projector with Lens Cap ViewSonic CD Wizard Contact you dealer immediately if any items are missing, appear damaged, or if the unit does not work Caution Avoid using the projector in dust environment.
Projection lens Front IR remote control sensor Caution Do not touch the lamp cover and exhaust vents during projector usage to prevent from possible burning. Do not looking into the lens or vents while the lamp is on. Strong light ray may be harmful to eyes.
Ventilation holes (exhaust) Bottom View Ceiling mount Tilt-adjustment feet This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package. Contact your dealer for information to mount the projector on a ceiling. ViewSonic...
- Use four directional buttons to select items or make adjustments to your selection. - Manually select an input source. (Left button) - Resynchronize the projector to the input signal from a computer. (Right button) MENU - Display or exit the on-screen display menus.
Connection Ports RS232 Reserved for installation control and firmware upgrades. COMPUTER IN Connect image input signal (analog RGB or component) to this jack. VIDEO Connect composite video output from video equipment to this jack. ViewSonic PJD6210/PJD6210-WH...
Switch in between high brightness performance performance ViewSonic that delivers saturation for Keystone+ / - Adjust image distortion caused by tilting the projector. Freeze Press " Accuracy color image. Press again to cancel the function. reeze" to pause the screen eeze PJD6210/PJD6210-WH...
Battery should not be in or near to fire or water, keep batteries in a dark, cool and dry place. If suspect battery leakage, wipe out the leakage and then replace a new battery. If the leakage adheres to your body or clothes, rinse well with water immediately. ViewSonic PJD6210/PJD6210-WH...
Do not drop the remote control or jolt it. Keep the remote control out of locations with excessively high temperature or humidity. Do not get water on the remote control or place wet objects on it. Do not disassemble the remote control. ViewSonic PJD6210/PJD6210-WH...
The figure above is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. The cables that come with the projector may differ from the above illustration. The included cables are based on actual shipment delivery.
When the Lamp LED begins flashing, the projector has entered stand-by mode. If you want to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered stand-by mode. Once in stand- by mode, simply press on the remote control to restart the projector.
Adjusting the Projector Adjusting the Projector Height The projector is equipped with two tilt-adjustment feet to adjust the image height. To level the image on the screen, turn the tilt-adjustment feet to fine-tune the height. To avoid damaging the projector, make sure that the tilt-adjustment feet are fully retracted before placing the projector in its carrying case.
Position the projector in a horizontal position; other positions can cause heat build-up and damage to the projector. Keep a space of 30 cm or more between the sides of the projector. Do not use the projector in a smoky environment. Smoke residue may build-...
Menu Operation The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. *1 Adjustable range and default setting vary depending on signal type. ViewSonic PJD6210/PJD6210-WH...
Adjust the settings with Press the MENU button, the screen will return to the main menu. To exit OSD, Press the projector will automatically save the new settings. Picture (Computer / Video Mode) Brightness Brighten or darken the image. Contrast Set the difference between light and dark areas.
Page 23
Menu Position Choose the menu location on the display screen. Projection Adjust the picture to match the orientation of the projector: upright or upside-down, in front of or behind the screen. Invert or reverse the image accordingly. Signal Type Specify the source to the Computer In terminal that you wish to project.
Page 24
Auto Source Automatically scan through all the input source. ECO Mode Use this function to dim the projector lamp light output which will lower power consumption and increase lamp life. This function will be unavailable when the DCR function is on.
Maintenance The projector needs proper maintenance. You should keep the lens clean as dust, dirt or spots will project on the screen and diminish image quality. If any other parts need replacing, contact your dealer or qualified service personnel. When cleaning any part of the projector, always switch off and unplug the projector first.
Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement. The lamp is extremely hot right after turning off the projector. If you touch the lamp, you may scald your finger. When you replace the lamp, wait for at least 45 minutes for the lamp to cool down.
Page 27
Replace the lamp cover and tighten the screw. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp. Reset the lamp hour. Refer to the Setting (Computer / Video Mode) menu.
50 - 85 Hz Operating: Temperature: 0°C to 40°C Humidity: 30%-85% Storage: Temperature: -20°C to 60°C Humidity: 30%-85% AC 100 - 240 V, 50 - 60 Hz, 2.3A 240 W 272.5 x 215 x 101.5 mm 2.4 kg (5.3lb) PJD6210/PJD6210-WH...
Solid blue power button is pressed, the brightness is 100%. After 30 seconds, it turns into 20%. 20% solid The projector is shutting and the fan is cooling blue the lamp for shutdown. 100% solid The lamp is going to reach its end of lifetime blue and must be changed soon.
Use the remote control within the effective range. Aim the remote control at the screen or at the front of the projector. Move the remote control so it is more directly in front of the projector and not as far to the side.
Power On/Off Pause the screen image Enter Management Menu Upward(For OSD) Leftward(For OSD) Rightward(For OSD) Downward(For OSD) ViewMatch Increase Keystone Value Decrease Keystone Value Resync The Input Signal Source Find The Input Signal Source Hide The Image With Blank BrilliantColor PJD6210/PJD6210-WH...
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS Electroser, Av Reforma No. 403Gx39 y 41, 97000 Merida, Yucatan. Tel: 01.999.925.19.16 Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico Latin America (Peru) www.viewsonic.com/la/ Macau www.hk.viewsonic.com...
If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Page 36
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.
Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
Page 38
E-Mail: rrrb@sureste.com Tijuana: Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembre Tijuana, Mexico 4.3: ViewSonic Mexico Limited Warranty Villahermosa: Compumantenimietnos Garantizados, S.A. de C.V. AV. GREGORIO MENDEZ #1504 COL, FLORIDA C.P. 86040 Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09 E-Mail: compumantenimientos@prodigy.net.mx...