Advertisement
Available languages
Available languages
PROGRAM THE REMOTE CONTROL (956EV, 956EV-P2, 956EVC AND 956EVC-P2)
1
Press and hold the program button
the remote control until the LED on
the front of the remote control
turns on.
Safety pin or
paper clip
Press and release the Learn
button on the garage door
opener.
4
Learn
Button
The Learn LED will light.
Within 30 seconds...
BATTERY
The LED on your remote will stop flashing when the battery is low and needs
to be replaced. To replace battery, open the case as shown. Insert battery
positive side up (+). Replace the battery with only 3V CR2032 coin cell
batteries. Dispose of old battery properly.
953EV, 953EV-P2, 953EVC AND
953EVC-P2
Pry open the case first in the
middle (1), then at each side (2
and 3) with the visor clip.
3
1
2
WARRANTY
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of this
product that it is free from defect in materials and/or workmanship for a
period of 1 year from the date of purchase.
1-800-528-9131
2
Press and release the remote control button you wish to use the
number of times that corresponds with the garage door opener type:
# of Presses
1
2
3
4
5
Press the remote control button
programmed in step 2 until the
garage door opener lights flash
or two clicks are heard.
956EV, 956EV-P2, 956EVC AND
956EVC-P2
Pry open the case with a
screwdriver blade.
Garage Door Opener Type
Yellow Learn Button (Security+ 2.0
)
®
Purple Learn Button (315 MHz Security+
Red/Orange Learn Button (390 MHz Security+
Green Learn Button (390 MHz Billion Code)
6
To test, press the programmed button on the remote control...
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V CR2032 coin batteries.
• DO NOT recharge, disassemble, heat above 212° F (100° C) or
incinerate.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Remote Control Transmitter 953EV: IFT #: RCPCH9518-0362
Remote Control Transmitter 953EVC: IFT #: RCPCH9518-0362-A1
Remote Control Transmitter 956EV: IFT #: RCPCH9518-0360
Remote Control Transmitter 956EVC: IFT #: RCPCH9518-0360-A1
REPLACEMENT PARTS
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137
(Models 953EV, 953EV-P2, 953EVC & 953EVC-P2 ONLY)
3
To exit programming mode,
press any remote control
button except the button
that was just programmed.
)
®
)
®
The garage door opener
will activate.
www.chamberlain.com
Advertisement
