Product Safety No�ce Don't Ride Un�l You Read This: This user manual will help you assemble and operate your new electric bike. Be sure to read all of the informa�on in this manual before riding. Always wear a helmet when riding your electric bike. NOTE TO ALL RIDERS UNDER 18 YEARS OF AGE: It's very important that you get Keep the two keys properly.
Abuse - We do not cover physical damage due to negligent care and extreme riding. Whenever you ride the Jasion Electric Bike, you risk severe injury or even death from loss of control, collisions, and falls. Use cau�on and ride at your own risk.
Assembly Product Overview LCD Display Display Controls Derailleur Grip Headlight Switch Thro�le Horn Switch LCD Display Stem Saddle 1. Place the ebike on a flat and stable 2.Carefully unfold the frame un�l it is in the upright posi�on. surface. Rear Suspension Headlight Suspension Front 3.
Assembly Assembly 6. Lock the quick release lever. 1.Unscrew the screw. Keep the screw 5. Put the screw and upper cover back in the 2.Remove the cylindrical protector. stem posi�on and �ghten the screw. and the upper cover. 7. Center the handlebar and adjust the direc�on, 8.
Page 7
4.Close the quick-release lever using your palm 3.Adujst the seat and the head of the seat is or finger. parallel with the top tube. Note: If the pedal/ chain doesn't run smoothly or something seems misaligned, please contact Jasion Support Team.
Page 8
Assembly Assembly Adjus�ng the Suspension Fork NOTICE: Ensure the seat post and seat are properly adjusted before riding. DO NOT raise the seat post beyond the minimum The suspension fork can move up and down up to 80mm to inser�on marking etched into the seat post cushion bumps in the riding surface, which can make riding √...
Start-up procedure Ba�ery Key Posi�ons Familiarize yourself with the key port and key posi�ons before riding the bike. The A�er the bike has been properly assembled according to the assembly video, all components are secured correctly, a cer�fied, reputable mechanic has checked the assembly, and you have read this en�re manual, photo below shows the key port aligned in key posi�on 3.
Remove the ba�ery Charge Your E-Bike Remove the ba�ery. Before using the electric bike, you must fully charge the ba�ery. Charging Port 1.Locate the frame quick-release lever and fold 2.Rotate the key counterclockwise, then press and rotate the key counterclockwise again un�l the the bike.
Display and Se�ng Charge Your E-Bike Ba�ery Level Display Backlight The ba�ery can be removed from the bicycle for charging. To remove the ba�ery, turn the key to the posi�on 3. (see the previous remove ba�ery sec�on for details). Then carefully pull the ba�ery out un�l the ba�ery detaches from the receptacle.
Page 12
2. BL MODE: A�er entering BL MODE, you can choose the black light level. LCD Display Controls 3. SPEED UNIT MODE: A�er entering SPEED UNIT MODE, you can choose the speed Opera�on Direc�ons unit from MPH TO KPH. Turn on bike un�l power engages(turn the ba�ery first) Wheel diameter and Max Speed Se�ng Press and hold...
Page 13
Personalized Se�ng Select the se�ngs via and press to enter the corresponding setup windows. Specific Press and hold on to enter see�ng mode, then press and hold Number Set up the item The screen appears again to enter Personalized Se�ng. Ba�ery voltage se�ng Do not change Pedal assist se�ng...
Page 14
Daily Care and Maintenance Cleaning and Storage If you see stains on the bike body, wipe them off with a damp cloth. If the stains can’t be scrubbed off, Speed sensor se�ngs Do not change apply some toothpaste, and brush them with a tooth brush, then wipe them off with a damp cloth. Notes: Do not clean the bike with alcohol, gasoline, kerosene or other corrosive and vola�le chemical solvents to prevent dire damage.
Page 15
No�ce: Before every ride, and a�er every 25-45 miles(40-72 km), we advise following the Regular inspec�on and maintenance are the key to ensure bikes from jasion func�on as intended, and to reduce wear and tear on their systems. Recommended service intervals are meant to be pre-ride safety checklist.
Page 16
Make sure the hub motor axle bolts are secured and the torque arm, torque arm bolt, and torque Thro�le Jasion recommends that the max inflate is to 35 PSI for the stock �res on the jasion. Always stay within the manufacturer’s washers are in place.
Specifica�ons Troubleshoo�ng Most Common Solu�ons Symptoms Possible Causes ITEM SPECIFICATIONS 1. Insufficient ba�ery power 1. Charge the ba�ery The bike does not Model EB7ST 2. Faulty connec�ons work 2. Clean and repair connectors 3. Ba�ery not fully seated in tray 3.
Error Code Current issue For the return request, Jasion is not responsible for lost packages due to the carrier, or products received that can not be verified. Thro�le issue Received products that have damage determined to have been caused by the end-user Power motor issue maybe subject to denial of the return request.
Page 19
5. All accessories originally included with your purchase must be included with your return. ● Normal wear and tear of any Covered Component. 6. If you return a product to Jasion, (a) without an RMA from Jasion(b) without all parts ● Consumables or normal wear and tear parts (including without limita�on �res, tubes, included in the original package, Jasion retains the right to refuse delivery of such return.
Contact Us Contact us if you experience issues rela�ng to riding, maintenance and safety, or errors/faults with your JASION. Support Email: support@jasionbike.com Scan the QR code and join our Facebook Group. Share your riding experience with other rides and get an exclusive bonus! JASION LTD www.jasionbike.com...
Need help?
Do you have a question about the EB7-ST and is the answer not in the manual?
Questions and answers