Summary of Contents for Bicom Systems Aastra 9112i
Page 1
Aastra 9112i How To (c) 2003-2010 Bicom Systems...
Page 3
Aastra 9112i How To (c) 2003-2010 Bicom Systems All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher.
Aastra 9112i How to use Aastra 9112i with PBXware This "How to" is written as general guide on how to use Aastra 9112i with PBXware using 1.3.1.1095 SIP Aastra 9112i firmware. It covers the most common tasks that are required to have your Aastra 9112i working efficiently.
Registering Aastra 9112i Registering Aastra 9112i Requirements Manual Configuration Auto Provisioning Auto Configuration Requirements 1. Aastra 9112i firmware. - Make sure that the device is loaded with 1.3.1.1095 SIP firmware. 2. DHCP server. - Fully configured and operational DHCP server.
Page 10
Aastra 9112i How To STEP THREE: status. 1. Make sure the UAD is enabled. To check the UAD status navigate to "Settings:UAD", and click on the "edit" icon corresponding to "Aastra 9112i". (c) 2003-2010 Bicom Systems...
Page 11
Registering Aastra 9112i 2. Make sure "Status" is set to "active", "Auto provisioning" is set to "No" and "DHCP" is set to "Yes". (c) 2003-2010 Bicom Systems...
Aastra 9112i How To 3. Click on the "Save" button to save changes. 2.2.2 Creating Extension STEP ONE: Add Extension. 1. Navigate to "Extensions". Click on "Add Extension". 2. The standard options window will be shown below. (c) 2003-2010 Bicom Systems...
Page 13
Registering Aastra 9112i 3. Select Aastra 9112i from "UAD" select box. 4. Select Location: "Local" or "Remote". Note: -"Local" is for all extensions registered on LAN. -"Remote" is for all extensions registered from remote networks, WAN, Internet etc. 5. Click on the "Next" button.
Page 14
Aastra 9112i How To an example with details filled in 2. Click on the "Save" button. an example with details filled in 3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail address associated with this extension.
- Connect the ethernet port to a hub, router switch as to access LAN. After successfully connecting the Aastra 9112i to the electricity and data networks it is time to register it to PBXware. STEP TWO: Aastra 9112i address. (c) 2003-2010 Bicom Systems...
Page 16
6. Use the "Navigation" button to navigate down to "IP Address". 7. Press the "Enter" button. STEP TWO: Aastra 9112i Interface. 1. Open a new browser window and enter the IP address in order to access Aastra 9112i administration interface. Example: http://192.168.1.101/...
Page 17
Registering Aastra 9112i an example with IP address 2. Hit "Enter" on your keyboard. STEP THREE: Configuring Aastra 9112i. 1. Click on "Line 1" link. 2. Enter the following details into the respective fields. REQUIRED FIELDS: Phone Number PBXware extension number. Example: 1000 Proxy Server IP address of PBXware server.
Page 18
Example: John Smith Other fields Other "options" or "fields" should be left blank or as is by default, they have no importance for registering the Aastra 9112i to PBXware. 3. Click on the "Save Settings" button. 4. Click on the "Reset" link.
Registering Aastra 9112i 5. Click on the "Restart" button to restart Aastra 9112i so that the changes take effect. - Conclusion: If everything is done as above described you should have successfully registered your Aastra 9112i to PBXware. Dial *123 to verify registration.
Page 20
Aastra 9112i How To STEP THREE: status. 1. Make sure the UAD is enabled. To check the UAD status navigate to "Settings:UAD", and click on the "edit" icon corresponding to "Aastra 9112i". (c) 2003-2010 Bicom Systems...
Page 21
Registering Aastra 9112i 2. Make sure "Status" is set to "active", "Auto provisioning" is set to "Yes" and "DHCP" is set to "Yes". (c) 2003-2010 Bicom Systems...
Aastra 9112i How To 3. Click on the "Save" button to save changes. 2.3.2 Creating Extension STEP ONE: Add Extension. 1. Navigate to "Extensions". Click on "Add Extension". 2. The standard options window will be shown below. (c) 2003-2010 Bicom Systems...
Page 23
Registering Aastra 9112i 3. Select Aastra 9112i from "UAD" select box. 4. Select Location: "Local" or "Remote". Note: -"Local" is for all extensions registered on LAN. -"Remote" is for all extensions registered from remote networks, WAN, Internet etc. 5. Click on the "Next" button.
Page 24
Aastra 9112i How To an example with details filled in 2. Click on the "Save" button. an example with details filled in 3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail address associated with this extension.
- Connect the ethernet port to a hub, router switch as to access LAN. After successfully connecting your Aastra 9112i to the electricity and data networks, it is time to register it to PBXware. "TFTP Server" must be set with TFTP server value.
Page 26
6. Use the "Navigation" button to navigate down to "IP Address". 7. Press the "Enter" button. STEP THREE: Aastra 9112i Interface. 1. Open a new browser window and enter the IP address in order to access Aastra 9112i administration interface. Example: http://192.168.1.101/ (c) 2003-2010 Bicom Systems...
Page 27
2. Hit "Enter" on your keyboard. STEP FOUR: Configuring TFTP server. 1. Login to the Aastra 9112i Web Interface. You'll be prompted to enter a username and password. The factory default username is lower case "admin" and password is "22222".
Page 28
Aastra 9112i How To an example with details filed in 3. "TFTP Server" must be set with TFTP server value. Example: 192.168.1.2 4. Click on the "Save Settings" button. 5. Click on the "Reset" link. (c) 2003-2010 Bicom Systems...
Registering Aastra 9112i 6. Click on the "Restart" button to restart Aastra 9112i so the changes take effect. Auto Configuration Requirements Auto Configuration 2.4.1 Requriements 1. Make sure your devices are properly connected to the same as your PBXware. 2. Make sure that all devices are set to Factory Defaults.
Page 30
Aastra 9112i How To an example with range of IP addresses 4. After the PBXware has finished searching for devices, a list of all devices found will be shown. 5. Change the activation status from "Not Activated" to "Auto Configuration" for one or more displayed devices of your choice.
Page 31
Registering Aastra 9112i an example with list of found devices 7. After you have edited a device, a pop up window will appear. (c) 2003-2010 Bicom Systems...
Page 32
Aastra 9112i How To an example with 4 configured lines 8. Aastra 9112i has 4 lines available, you can configure just one or all of them as shown above. Line 1 example Name: John Smith E-mail: john@domain.com Ext: 1000 PIN: 1223 Secret: Enter an at least 6 digit or letter long secret.
Page 33
Registering Aastra 9112i 11. Device(s) will automatically reboot and be auto configured. (c) 2003-2010 Bicom Systems...
4. Navigate to the bottom of the page and click on the "Save Settings" button. 5. Reboot the phone to apply the new settings. NOTE: At the time, paging option is set for all lines and works once the handset is picked up. Paging tested with Firmware version 1.3.1.1095. (c) 2003-2010 Bicom Systems...
- WAN = Wide Area Network. - Web Interface = A web interface is the system of controls with which the user controls a device. (c) 2003-2010 Bicom Systems...
Page 38
Aastra 9112i How To (c) 2003-2010 Bicom Systems...