Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TOKNAV T10Pro
Summary of Contents for TOKNAV T10Pro
- Page 2 1. Introduction to the T10Pro 01-03 2. PCR100 Data Controller 03-04 3. SurPro software operation 05-32 4. Tilt measurement 32-34 5. Host Registration and 35-38 Software Licensing...
- Page 3 1. Introduction to the T10Pro 1.2. Operating Instructions 1.1. Exterior description 1.2.1. SIM card installation Figure 1 Figure 2 A. Satellite Indicator Light; B. Power button; Opening the dust plug; C. 7 Pin data connector (Serial/External Power); Install the SIM card according to the indication D.
- Page 4 1.2.2. The meaning of the instrument keys 1.2.3. Power on and off and indicator lights Power on: Press and hold the power button until the voice prompts "Booting" and release, the device starts up, and the panel lights flash until the voice prompts "Boot completed"...
-
Page 5: Key Features
1.2.5. WEB access The receiver supports Web access to the built-in page for with measuring handbook software. T10pro has profes- viewing host information and upgrading firmware. The sional IP68 grade protection, which is suitable for harsh host's WIFI hotspot is turned on by default, and the outdoor environments. - Page 6 Run the SurPro measurement software, execute [Config- device type, as shown in Figure 10, click [Search for You can also connect the T10Pro through the NFC function of the mobile phone, put the NFC area of the Bluetooth devices], find the Bluetooth name of the...
-
Page 7: New Project
New Project You can set the coordinate system for other parameters according to the actual operation requirements. new project, enter the project name, others are additional File import information, which can be left blank, or filled in according Copy the data files to be imported to the SurPro Survey to the actual data, and click [OK] (Figure 14). -
Page 8: Parameter Conversion
Document export Parameter conversion Example: four-parameter conversion. angle format and file format, then click [Export]. Then we 3.5.1 Correctly configure the mobile station to obtain a select the output file storage path, and click [Export], the fixed state, click [Collect Point] to measure two known data file is exported successfully (Figure 17, 18). - Page 9 measurement points from the point library (Figure 24), click the […] button in the lower right corner, select and add two sets of data. Then click Calculate Four [Calculate Option] in the pop-up window (Figure 21), and Parameters(Figure 25), scroll down the parameter report set the parameter settings (Figure 22).
-
Page 10: Point Calibration
Point Calibration ter calculate] below (Figure 27). Enter the known plane coordinates, and click on the geodetic coordinates for more acquisition methods, which include "positioning acquisition" and "point library acquisition", after the input is completed, click [Cal.] (Figure 28). After the calculation is completed, click [OK] to enable the base station transla- Figure 25 Figure 26... - Page 11 Rover mode setting stage, the internal network of the host has not been successfully started, and the access point cannot be obtained at this time, you can first use the mobile [Built-in Network], [Mobile Phone Network] or [Built-in network to obtain the access point to select. Then click Radio] for the data link mode.
- Page 12 Static mode setting 3.7.3 Select [Built-in radio], you need to connect the UHF radio antenna under the host (Figure 33), and then select the corresponding radio frequency and communication value, altitude cutoff angle, sampling interval, antenna protocol (Figure 34). information and other parameters, click [OK] to start storing static data (Figure 35, 36).
- Page 13 Base station mode setting 3.8.2 Static file downloads Log in to the receiver web page (see 1.2.5 for details), click [File] (Figure 37). Find the folder corresponding to the Network], [Built-in Radio] or [External Radio] for the data time to download the static data (Figure 38). link mode.
- Page 14 T10Pro base station, T10Pro rover station, power supply radio antenna under the host (Figure 40), and then select (12V), tripod. the corresponding radio frequency and communication 2 Instrument set-up. protocol (Figure 41). (1) Erection of base station. Red dot mark...
- Page 15 Harxon radio (eRadio) button interface, set the radio T10Pro base station IOIOI Seven-core interface, the crocodile clip of the seven-core radio cable is connected the protocol, and set the serial port baud rate to 115200 to the positive and negative poles of the power supply (Figure 44 and 45).
- Page 16 The SurPro App displays the following screen (Figure 48). Figure 47 The T10Pro rover station is powered on and fixed on the carbon fiber centering pole (Figure 47). During measure- ment, set the working mode to built-in radio, set the for the protocol (Figure 48).
- Page 17 3.10 Collect Point S: number of available satellites, V: number of visible satellites, power information). The bottom column of this interface displays the point name currently to be collect- ed, as well as the antenna height parameter settings. There are six display columns at the bottom of this interface.
- Page 18 The meaning of each icon in the point measurement to be displayed. The contents that can be displayed here page is as follows: mainly include: north coordinate, east coordinate, elevation, longitude, latitude, geodetic height, speed, time, upper gear slant distance, upper gear horizontal distance, upper point height difference and base station Control point measurement: At present, RTK technology can distance (Figure 54).
- Page 19 3.11 Stake Point flag icon on the upper right to enter the stakeout point library (Figure 58). Click the "..." icon in the lower right corner to import the point just measured from the measurement point library and perform the stakeout can see the distance between the current coordinate point and the known point (Figure 60).
- Page 20 4.1 Operating instructions for the tilt 4.2 Use of the mainframe for tilt measurement measurement function 1. When the tilt measurement is turned on, sometimes corner to input the antenna height parameter (centering the tilt icon will change from green to red with movement pole height), and then turn on the tilt measurement icon and rotation.
-
Page 21: Software Licensing
5. Host Registration and Software Licensing When it is found that the host registration code has expired, then we need to enter a new registration code, 5.1 Host registration The host registration code is a valid time code to autho- the new registration code in the box for entering the rize the host to use the positioning function. - Page 22 not be available. Note: The software must be connected When the upper right corner of the [Configure] main to the host computer to be authorized before the license code can be entered. we need to enter a new registration code. Execute The SurPro measurement authorization code is the the new registration code in the box for entering the authorization code for using most of the functions of the...
Need help?
Do you have a question about the T10Pro and is the answer not in the manual?
Questions and answers