Advertisement
Quick Links
Advertisement
Related Manuals for Wind Crest SERIAL BUS
Summary of Contents for Wind Crest SERIAL BUS
- Page 1 Evacuation & Fire Fighting Intercom System TYPE: SERIAL BUS...
- Page 2 IMPORTANT: READ PRIOR TO INSTALLATION Each Landing Speaker supplied should be installed on the designated landing as they are pre-assigned a unique address (Do not change the address as they are assigned from the factory. Contact Windcrest before changing address). The Master Switching Panel (with push buttons for each landing) should be ...
- Page 3 Fire Fighting Intercom Operation: Patch Cable When the system is operated via turning ON the Fire Fighting Switch on the panel, a three way communication link will be turned ON between the Panel, Motor Room Speaker & the Lift Car Speaker. Fire Fighting Intercom “Press to speak”...
- Page 4 After every 10 outstations a Power Booster will be required. Refer to Page 6. Motor Room (This area represents the Motor Room) Evacuation Intercom Power Supply CT5 Cable 6 way Windcrest AD1000EN-4R System Top most landing Car Speaker Interface T op of Li ft L ift Car L ift Pi t GSM/Phone Line...
- Page 5 After every 10 outstations a Lift Shaft Power Booster will be required. (This area represents the Lift Shaft) Refer to Page 6. Evacuation Intercom Top most landing Power Supply CT5 Cable 4 way 6 way BT Socket Windcrest AD1000EN-4R MRL System Car Speaker Windcrest...
- Page 6 After every 10 outstations a Power Booster will be required. Refer to Page 6. Top most landing CAT 5 Cable Fire Fighting Intercom Travelling Cable Landing CAT5 Cable EVACUATION INTERCOM (Everything here is outside the lift, but near the lift door on the wall) Patch cable 230 VAC...
- Page 7 CAT5 Cable Lift Shaft CAT5 Cable Evacuation Intercom Power Supply This area represents Lift Motor Room or Top of the Lift Shaft CAT5 Cable 10 outstations To Lift Car EVACUATION INTERCOM Travelling Cable Min. 6 way screened & twisted with min. of 0.75mm conductor (Travelling Cable will be required if the system is...
- Page 8 CAT5 Cable Lift Shaft CAT5 Cable Evacuation Intercom Power Supply This area represents Lift Motor Room or Top of the Lift Shaft CAT5 Cable 10 outstations Evacuation Intercom Power Supply Unit EVACUATION INTERCOM 12 Way Cable Power M 0 B Booster CAT5 Cable 12 Way Cable...
- Page 9 CAT5 Cable Lift Shaft CAT5 Cable Evacuation Intercom Power Supply This area represents Lift Motor Room or Top of the Lift Shaft CAT5 Cable 10 outstations EVACUATION INTERCOM 12 Way Cable Power Booster CAT5 Cable 12 Way Cable 10 outstations EVACUATION INTERCOM POWER BOOSTER Power...
- Page 10 6 Way 6 7 8 Speaker Box nth Floor Landing WRONG 1. Orange/White……….A (Data) 2. Orange……………….B (Data) 3. Green/White ………..+24V 4. Blue…………………..Audio Speaker Box 5. Blue/White…………...Audio nth Floor Landing 6. Green………………...Ground 7. Brown/White…………+24V 8. Brown………………...Ground RJ45 to Terminal 25-30V Data – Maximum voltage 5Vpp 25-30V DC, when all speakers are...
- Page 11 Cable from the other landing terminator Connect bus terminator to the last outstation on each bus. RJ45 to Terminal A = White B = Green + = Pink GND = Gray BT (Audio)= Blue BT (Audio) = Yellow 25-30V Data – Maximum voltage 5Vpp 25-30V DC, when all speakers are...
- Page 12 Evacuation Functions Interconnection Connect the main Evacuation Panel to the Control Box. Connect all the Landing Speakers to the bus. Lift Controller Contacts are provided on the Main Panel. Lift Controller Spare Contacts:- Blue or Orange - Common Green or White- Normally Open Yellow- Normally Closed Operation To activate the evacuation system, place the EURO switch in the ON position.
- Page 13 Fire Fighting Function Interconnection Connect all the Landing Speakers and the Motor Room speaker to the bus. Lift Controller Contacts are provided on the Main Panel. Lift Controller Spare Contacts on the Fire Fighting Switch:- Orange - Common White- Normally Open Yellow- Normally Closed Operation To activate the Fire Fighting system, place the EURO switch in the ON position.
- Page 14 All speakers have unique address. This address is set by the Dip Switch on the back of the each speaker box. Following are the arrangements for the Dip Switch for the different speaker box. Note: X – Do Not Care Car Speaker Motor Room Fire Fighting Speaker Master Panel :- This address will define the number of outstations (Excluding Lift Car (Default)).
- Page 15 Green (Autodialler ‘G’) Black (Not Used) Note:- If the Autodialler is Red (Autodialler ‘+’) already wired, please Yellow (Autodialler ‘Y’) refer to the Page 12. White Cable for Lift Car Alarm Push Pictogram/Loop/Amplifier in the Lift Serial Data Controller To Autodialler ‘+’ To Autodialler ‘A’...
- Page 16 Green (Autodialler ‘G’) Black (Not Used) Yellow (Autodialler ‘Y’) Red (Autodialler ‘+’) White Cable for Pictogram/Loop/ Disconnect the wire connected to Amplifier the Existing Autodialler Terminal “A” and connect to this terminal Serial Data Controller Disconnect the wire connected to the Existing Autodialler “+”...
- Page 17 Serial Evacuation-AD1000EN-xR Interface for the Car Speaker & Lift Car Alarm Push...
- Page 18 CAR/D CAR/S PIT/D PIT/S TOP/D TOP/S MR/S Serial Evacuation-AD1000EN-xR Interface for the Car Speaker & Lift Car Alarm Push...
- Page 19 M 0 B + - 12V Output Low Battery Relay Output Mains Detection Relay Output (“0” - Common, “B” - Normally Open) (“0” - Common, “M” - Normally Open) Low Battery = Closed Mains Failure = Closed Battery Good = Open Mains Good = Open Page 18 Drawing: Mains &...
Need help?
Do you have a question about the SERIAL BUS and is the answer not in the manual?
Questions and answers