Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LEGRAND Da-Lite Contour Electrol
Summary of Contents for LEGRAND Da-Lite Contour Electrol
- Page 1 INSTRUCTION BOOK FOR Contour Electrol ® ®...
-
Page 2: Important Safety Instructions
Legrand AV makes no representation of warranty, expressed or implied, regarding the information contained herein. -
Page 3: Installation
Installation NOTE: Remove the black tape and rubber bands from the slat bar 5 11/16" after the case has been installed. There are three ways to install the Contour Electrol — Wall Mount, Ceiling Mount, or Ceiling Hook. Procedures for each method are as follows: 2 5/16"... -
Page 4: Electrical Installation
Installation (continued) Ceiling Hook Mount Ceiling Hook Bracket 1. The ceiling hook mount brackets are tied together and attached to the ceiling flush mount bracket at one end 1/4 X 5/8" Flat Head of the case. Remove the ceiling hook mount brackets. Screw 2. - Page 5 Contour Electrol Installation for 120V Screens ® ® Wall Switch 120V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch RJ-45 Input adjustments, EVEN if a third party control system is used. Therefore, it is advised to locate the wall switch in an Junction Box Cat5e or Cat6 Cable...
- Page 6 Contour Electrol Installation for 230V Screens ® ® Wall Switch 230V Wiring Diagram IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch RJ-45 Input adjustments, EVEN if a third party control system is used. Therefore, it is advised to locate the wall switch in an Junction Box Cat5e or Cat6 Cable...
- Page 7 Contour Electrol Installation for 230V Screens (continued) ® ® 230V Wiring Diagram with Opitonal European Style Wall IMPORTANT NOTE: The European style wall switch is for Switch operation only and CANNOT be used to make limit switch adjustments. Therefore, it is advised to locate the limit Use 3-conductor 20–24 gauge wire to connect European style adjustment wall switch in an accessible location.
-
Page 8: Screen Adjustment
Screen Adjustment If your Contour Electrol was ordered as a complete unit, the up and 4. To adjust the up limit switch, press and hold the up tactile down limits were pre-set by Da-Lite. If your screen and roller button until the LED on back of switch turns solid green. This assembly was ordered separately from the case, or if general will put the motor in limit set mode. -
Page 9: Operation Of Screen
Operation of Screen Operation & Limit Adjustment Wall Switch “Up” Button Press ”DOWN” button on screen switch and screen will deploy out of case in downward direction. “Stop” Button 2. Press “STOP “button on screen switch and screen will stop if in movement. -
Page 10: Troubleshooting
Troubleshooting Symptom Cause Solution Verify 115-125V (or 220-240V). If insufficient voltage, rewire Incorrect line voltage. incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker. Screen will not operate and motor does not hum. Check above. Tighten all loose wire connections. Correct any improper connections. - Page 11 LIMITED FIVE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Legrand AV Inc. warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.
- Page 12 P +852 2145 4099 E av.asia.sales@legrand.com COMMERCIAL BRANDS © 2023 Legrand AV Inc. DL-0114 (Rev. 5) 12/23 Da-Lite is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification purposes and are trademarks of their respective Chief | Da-Lite | Middle Atlantic | Projecta | Vaddio owners.
Need help?
Do you have a question about the Da-Lite Contour Electrol and is the answer not in the manual?
Questions and answers