Subscribe to Our Youtube Channel
Related Manuals for MCZ PERFORMA 15HQ EASYCLEAN H1
Summary of Contents for MCZ PERFORMA 15HQ EASYCLEAN H1
- Page 1 INSTALLATION GUIDE PELLET BOILER PERFORMA 15HQ EASYCLEAN H1 PERFORMA 20HQ EASYCLEAN H1 PERFORMA 25HQ EASYCLEAN H1 PERFORMA 30HQ EASYCLEAN H1 PART 2 - OPERATION AND CLEANING Instructions in English...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS ....................II 9-CONTROL PANEL ......................3 10-FIRST START-UP .....................4 11-MENU STRUCTURE ....................8 12-INFORMATION MENU ...................11 13-SETTINGS MENU ....................14 14-TECHNICAL MENU ....................32 15-SAFETY DEVICES AND ALARMS ................33 16-RECOMMENDATIONS FOR SAFE USE ...............39 17-CLEANING AND MAINTENANCE................40 18-FAULTS/CAUSES/SOLUTIONS .................46 19-CIRCUIT BOARD ....................49... -
Page 3: 9-Control Panel
9-CONTROL PANEL CONTROL PANEL DISPLAY MENU A - DISPLAY; indicates a series of information on the boiler, as well as the identification code of any malfunction. B - Function selection key indicated by the upper display (i.e. start-up/shutdown) C - Function selection key indicated by the upper display (i.e. increase/scrolling) D - Function selection key indicated by the upper display (i.e. -
Page 4: 10-First Start-Up
10-FIRST START-UP FIRST START-UP REV.SOFTWARE NUM BANCA DATI At initial start-up, after connecting the power cable and pressing the I/O button, the boiler display will show wording for the software version and database number (after a few seconds it will move on to the next screen). If the language has already been set, the next screen will be OFF, otherwise one enters the following parameter. - Page 5 10-FIRST START-UP SCREEN OFF If a LANGUAGE has already been set, the display will go to OFF. By pressing any one of the keys (B, C, D, E) the first screen will appear with the wording OFF displayed. From this screen, pressing keys “B” and “E”...
- Page 6 10-FIRST START-UP Start-up To switch on the boiler, keep the “B” (ON) key on the panel pressed. The boiler starts an ignition procedure that brings the flame to a suitable level to Supply Power. 10:13 TIMER1 23° 25° OFF 63° TEMP MENU Supplying power...
- Page 7 10-FIRST START-UP TEMPERATURE Press the “D” TEMP button (see the image on the previous page) to set the temperature of the heating and possibly the domestic water (if the storage cylinder with probe is configured - see the menu settings input aux). Select what is to be set and then using the C and D keys increase/decrease the temperature, use the E key to confirm while the B key is used to exit and return to the main MENU.
-
Page 8: 11-Menu Structure
11-MENU STRUCTURE MENU STRUCTURE To enter MENU press the “E” key (MENU). 10:13 TIMER1 23° 25° OFF 63° TEMP MENU Next, this screen with the following functions is displayed: FUNCT. PROGRAMAS Sub-menu INFORMATION SETTINGS FUNCTIONS EXIT PROGRAMMES INFORMATION SETTINGS PROGRAMMES In this case it is possible to choose the programme to be set. - Page 9 11-MENU STRUCTURE In the MENU screen, move the cursor with arrows “C”-”D” and select PROGRAMS, press ok “E” to confirm. Next select the programme you wish to set. Once completed, always press “ACTIVATE” to confirm the choice of programme. The TIMER 1 and 2 programs are freely programmable for each 1/2 hour of the day on three different temperature indicators (T1-T2-T3) and in different ways for each day of the week.
- Page 10 11-MENU STRUCTURE MANUAL This function can be activated from the menu PROGRAMME by pressing the key “C” ACTIVE. When this function is activated, the boiler no longer follows time programming of TIMER 1 or 2 programs, but it keeps the temperature set in the main screen throughout the 24-hour time period.
-
Page 11: 12-Information Menu
12-INFORMATION MENU INFORMATION To enter the INFORMATION menu, proceed as follows: from the main/initial screen, press the “E” Menu button, scroll using the “D” arrow key, up to the Information item, press the “E” ok key, scroll again using the “D” arrow key up to software/data memory/all.memory/boiler state and select the desired item, press OK using the “E”... - Page 12 12-INFORMATION MENU DATA MEMORY-INFORMATION INFORMATION-DATA HYSTORY WORKING HOURS = 100 TOTAL IGNITIONS = 20 TEST DATE = 15/01/2013 EXIT The available data in this function are: WORKING HOURS TOTAL IGNITIONS TEST DATE ALARM MEMORY-INFORMATION It gives information about the last alarms detected. INFORMATION-ALARM HYSTORY ALARM 02 - 28/06/13 13:44 1 ALARM 02 - 21/06/13 08:03 2...
- Page 13 12-INFORMATION MENU BOILER STATE-INFORMATION This menu is particularly useful if you want to verify the boiler’s working condition (State). From the OFF screen, press the “E” Menu button, scroll with the “D” arrow key, up to the Information item, press the ok “E” key, scroll again with the “D”...
-
Page 14: 13-Settings Menu
13-SETTINGS MENU SETTINGS To enter the menu SETTINGS, proceed as follows: from the OFF screen, press the “E” Menu key, scroll with the “D” arrow key up to Settings item, press the ok “E” key, scroll again with the “D” and/or “C”... - Page 15 13-SETTINGS MENU AUTOECO (factory activated) SETTINGS-AUTOECO IF YOU ACTIVATE THE AUTOECO, DEACTIVATE ACTIVATE THE STOVE GOES OFF WHEN THERE AUTOECO AUTOECO ARE NO MORE HEAT REQUESTS INFO EXIT The Auto eco mode turns the boiler off when heating the system does not require heat, depending on the menu-settings-input aux configuration.
- Page 16 13-SETTINGS MENU FEED SCREW LOADING (only with the boiler off) SETTINGS-FEED SCR LOAD USE THE 'FEED SCREW LOADER' WHEN DEACTIVATE ACTIVATE THE FEED SCREW IS EMPTY AND LOAD LOAD YOU MUST LOAD IT QUICKLY INFO EXIT This function is for filling the pellet loading system. It can only be activated with the boiler off. To enter the function: from the Settings menu - press ok (E key), press the D key (arrow key) and scroll up to load feed screw, press OK (E key) and activate/ deactivate the function, press ok (“E”...
- Page 17 13-SETTINGS MENU PELLET RECIPE A password is required to enter the menu, enter the code 0000. Once the password has been entered, the message “ONLY FOR TECHNICIAN “. SETTINGS-LOAD-RECIPE CHANGE BY PERCENT THE FEED SCREW +15% SPEED TO ADAPT THE STOVE TO THE TYPE OF PELLET INFO EXIT...
- Page 18 13-SETTINGS MENU CLEANING CYCLE SETTINGS-CLEANING IMMEDIATELY ACTIVATE A CLEANING DEACTIVATE ACTIVATE CYCLE OF THE BRAZIER CLEANING CLEANING INFO EXIT This function can only be activated with the boiler in OFF supply: from the Settings menu- press ok (E key), press the D key (arrow key), scroll up to the “ciclo pulizia” (cleaning cycle) press OK (E key)- Activate/deactivate cleaning.
- Page 19 13-SETTINGS MENU AUX INPUT (using one of the following parameters excludes the other) The auxiliary input allows you to choose the system configuration type based on which the boiler is connected. To enter the function press: from the Settings menu- press ok (E key), press the D (arrow) key and scroll up to the Aux Input item and press OK (E key). Using the “C” and “D”...
- Page 20 13-SETTINGS MENU • External probe It makes it possible to work with system temperature adjustment. If installing an external probe on terminals 1 and 2 (NTC 10KOhm at 25°C b=3435) water temperature is automatically calculated by the electronics based on external temperature according to the curves shown below: The external probe must be installed on an external wall exposed towards North or North-West.
- Page 21 13-SETTINGS MENU • Puffer thermostat To activate this option, connect a Normally Open (N.O.) contact thermostat to points 1 and 2 of the back 9-pole terminal board. Even with this configuration the purpose of the room probe on the boiler is only to control the heating system pump controlled by the potential free contact on terminals 7-8-9, if the system pump is activated in Aux out mode.
- Page 22 13-SETTINGS MENU CONNECTOR IF INSTALLING THE TROLLEY If the trolley is installed (optional) the “W1” connector that will be found on the right side of the boiler must be connected to the connector available on the kit. An additional electronic board “W2” is also provided with the trolley. All instructions concerning the installation and operation of the trolley are provided with the optional accessory.
- Page 23 13-SETTINGS MENU BOILER PRINCIPLE DIAGRAMS The following diagrams are to be used only as a guideline. For proper connection, always follow the notes of the plumbing and heating installer. The plumbing system must meet local, regional, or national regulations in force.
- Page 24 13-SETTINGS MENU SYSTEM WITH: DIRECT PELLET BOILER AND DHW BOILER Adjustable setting VALUES WATER TEMP 60° C - 80°C BOILER TEMP. 10°C - 70°C Parameters to be set Settings Value AMB Input Room thermostat AUX Input Boiler Probe AUX Output None Hydraulic diagram Num.
- Page 25 13-SETTINGS MENU SYSTEM WITH: PELLET BOILER, PUFFER AND BOOSTER PUMP Adjustable setting VALUES STORAGE TEMP. 50°C - 80°C Parameters to be set Settings Value AMB Input Room Thermostat AUX Input Puffer Probe AUX Output Puffer Pump Hydraulic diagram Num. Description Num.
- Page 26 13-SETTINGS MENU SYSTEM WITH: PELLET BOILER, PUFFER AND EMERGENCY BOILER (WALL-MOUNTED) Adjustable setting VALUES STORAGE TEMP. 50°C - 80°C Parameters to be set Settings Value AMB Input None AUX Input Puffer Probe AUX Output Auxiliary boiler Hydraulic diagram Num. Description Num.
- Page 27 13-SETTINGS MENU SYSTEM WITH: PELLET BOILER, PUFFER AND DHW BOILER Adjustable setting VALUES STORAGE TEMP. 50°C - 80°C BOILER TEMP. 10°C - 70°C Parameters to be set Settings Value AMB Input Puffer Probe AUX Input Boiler Probe AUX Output None Hydraulic diagram Num.
- Page 28 13-SETTINGS MENU OUTPUT AUX SETTINGS-OUTPUT AUX SET AMBIENT INPUT: REMOTE BOILER ALLARM IN T = (TERMINALS 3 - 4) INFO EXIT The AUX output makes it possible to use a relay contact, based on the system configuration type chosen in the Aux Input menu. It acts on contact 7-8-9 of the external terminal board: •...
- Page 29 13-SETTINGS MENU INPUT AMB SETTINGS - INPUT AMB SET AMBIENT INPUT: AMB PROBE THERM.AMB (TERMINALS 3 - 4) INFO EXIT The room input is used to set the probe or the thermostat at terminals 3-4 of the back terminal board of the boiler. The boiler has the room probe set as default factory settings.
- Page 30 13-SETTINGS MENU PWM PUMP This function is used to set high efficiency pump speed. To enter the function press: from the Settings menu- press ok (E key), press the C-D key (arrow) and scroll up to PWM Pump, press OK (E key)- Modify the percentage using the central C and D keys, press the E key to confirm.
- Page 31 13-SETTINGS MENU DISPLAY SETTINGS-DISPLAY CONTRAST BRIGHTNESS Adjust display contrast and brightness. This function is found in: from the Settings menu- press ok (E key), press the C-D key (arrow) and scroll up to Display, press OK (E key)- Modify the settings using the B - C - D keys and press the E key to confirm.
-
Page 32: 14-Technical Menu
14-TECHNICAL MENU TECHNICAL MENU To access the technical menu you must contact the service centre as it requires a password. To make changes in the technical menu, enter the SETTINGS menu, press the “E” (OK) key, scroll using the “C”-”D” arrows keys and select Technical menu and press OK (E key)- Enter the password and press the E key to confirm. -
Page 33: 15-Safety Devices And Alarms
15-SAFETY DEVICES AND ALARMS SAFETY DEVICES The product is fitted with the following safety devices ACTIVE + Besides adjusting the boiler operation, it also guarantees that the pellet loading feed screw is blocked if unloading is blocked or there is significant back pressure. - Page 34 15-SAFETY DEVICES AND ALARMS TAMPERING WITH THE SAFETY DEVICES IS PROHIBITED If the boiler is NOT used as described in this instruction manual, the manufacturer declines all responsibility for damage to persons and property that may arise. The manufacturer furthermore refuses to accept responsibility for damage to persons and property arising from the failure to observe all the rules contained in the manual and in particular: •...
- Page 35 15-SAFETY DEVICES AND ALARMS ALARM ALERTS If there is an operational anomaly, the boiler enters the alarm phase displaying the problem that has taken place through a code, a brief description of the alarm type and an acoustic warning. The following table describes the possible alarms indicated by the boiler, associated to the respective code that appears on the panel and helpful tips to solve the problem.
- Page 36 15-SAFETY DEVICES AND ALARMS WRITTEN ON THE TYPE OF PROBLEM SOLUTION DISPLAY Check that the lower compartment is clean (see the pages dedicated to boiler cleaning) and verify that it is Faulty smoke fan. not obstructed; clean it and cancel the alarm. FLUE GAS FAN If the alarm persists, contact the service centre.
- Page 37 15-SAFETY DEVICES AND ALARMS WRITTEN ON THE TYPE OF PROBLEM SOLUTION DISPLAY Possible fault in the safety component. Contact an authorised service centre to have the component Room probe failure checked and, if needed, replace the component. ALARM A18 TRIGGERED A bracket “s”...
- Page 38 15-SAFETY DEVICES AND ALARMS When the boiler enters an alarm state, an automatic cooling/shut-off phase begins, at the end of which the cause of the alarm is displayed on the small panel. Before resetting the alarm, follow the controls indicated in the previous table, and then press the RESET key for a few seconds (or remove power to the boiler using the main ON/OFF switch on the back of the boiler).
-
Page 39: 16-Recommendations For Safe Use
16-RECOMMENDATIONS FOR SAFE USE ONLY CORRECT INSTALLATION AND APPROPRIATE MAINTENANCE AND CLEANING OF THE APPLIANCE CAN GUARANTEE CORRECT OPERATION AND SAFE USE OF THE PRODUCT We would like to inform you that we are aware of cases of malfunctioning of domestic pellet-fuelled heating products, mainly due to incorrect installation and inappropriate maintenance. -
Page 40: 17-Cleaning And Maintenance
17-CLEANING AND MAINTENANCE Disconnect the product from the 230V power supply before performing any maintenance operation. DAILY OR WEEKLY CLEANING PERFORMED BY THE USER If the pellets in the tank run out, unburned pellets may accumulate in the brazier. Check the status of your brazier every 15 days. The automatic cleaning system means you don’t have to empty the brazier. - Page 41 17-CLEANING AND MAINTENANCE CLEANING THE ASH PAN (if the trolley - optional - is not installed) In the standard boiler, that is without the trolley, you must remove the ash pan “M” and empty the ash at least once a week. To do so you must open the door of the boiler “A”, open the lower door “J”...
- Page 42 17-CLEANING AND MAINTENANCE CLEANING THE SMOKE EXTRACTOR COMPARTMENT In the area behind ash pan “M”, there is the smoke cap “E”, which must be removed to clean the smoke extractor. Therefore: • loosen the screws “s” • remove cap “E” Now, use the nozzle of a vacuum cleaner, remove any ash and soot that may have built up in the lower exchanger indicated by the arrow.
- Page 43 17-CLEANING AND MAINTENANCE CLEANING THE SMOKE EXPULSION SYSTEM AND GENERAL CHECKS Clean the smoke extractor system, especially around the “T” joints, elbows and any horizontal sections of the smoke duct. For information on periodically cleaning the flue, contact a skilled chimney sweep. Check the integrity of the ceramic fibre seals on the door of the boiler.
- Page 44 17-CLEANING AND MAINTENANCE REPLACING THE OVERPRESSURE DISCHARGE FOR THE COMBUSTION CHAMBER Overpressure rubber bushing “G” of the combustion chamber (fig. A) may get worn and/or damaged, it is therefore necessary to replace it once a year to ensure correct system operation. To replace it, follow the instructions below •...
- Page 45 17-CLEANING AND MAINTENANCE CHECKING THE INTERNAL COMPONENTS ATTENTION! The internal electromechanical components must only be checked by qualified personnel whose technical expertise includes combustion and electricity. We recommend that an annual maintenance service is carried out (with a scheduled service contract). This service is essentially a visual and functional inspection of the internal components.
-
Page 46: 18-Faults/Causes/Solutions
18-FAULTS/CAUSES/SOLUTIONS ATTENTION: All repairs must be carried out exclusively by a specialised technician, while the boiler is completely cold and the electric plug is disconnected. ANOMALY POSSIBLE CAUSES SOLUTIONS The pellets are not fed into the combustion The pellet hopper is empty Fill the tank with pellets chamber. - Page 47 18-FAULTS/CAUSES/SOLUTIONS ANOMALY POSSIBLE CAUSES SOLUTIONS The stove runs for a few minutes and then Start-up phase is not completed Repeat start-up goes out Temporary power cut Wait for the automatic restart Clogged smoke duct Clean the smoke duct Faulty or malfunctioning temperature Check and replace the probes probes Pellets accumulate in the brazier, the glass...
- Page 48 18-FAULTS/CAUSES/SOLUTIONS ANOMALIES RELATED TO THE HYDRAULIC CIRCUIT ANOMALY POSSIBLE CAUSES SOLUTIONS Incorrect combustion adjustment. Check recipe No increase in temperature with stove in operation Boiler / system dirty. Check and clean the boiler. Insufficient stove power Check that the stove is properly sized for the requirements of the system Poor pellet quality Using pellets from the producer...
-
Page 49: 19-Circuit Board
19-CIRCUIT BOARD 13 14 15 MOTHERBOARD WIRING KEY AUX RELAY (C-NO-NC) 15. PWM PUMP CONTROL HOME AUTOMATION CONTACT 16. CONTROL PANEL ROOM PROBE 17. WATER TEMPERATURE OVERLOAD CUT-OUT AUX INPUT 18. HOPPER OVERLOAD CUT-OUT SMOKE FAN ENCODER 19. BRAZIER CLEANING GEAR MOTOR ENCODER 20. - Page 52 Via La Croce n°8 33074 Vigonovo di Fontanafredda (PN) – ITALY Telefono: 0434/599599 a.s. Fax: +39 0434/599598 Internet: www.red-fire.it e-mail: info@red-fire.it 8902108500 REV 0 09/11/2020...
Need help?
Do you have a question about the PERFORMA 15HQ EASYCLEAN H1 and is the answer not in the manual?
Questions and answers