Tarmo 320281 Manual page 3

• If the reception of the water values fails within 3 minutes, "- -"
appears on the display and the symbol is not displayed. Check the
batteries of the transmitter and try it again. Check if there is any
source of interference.
• You can also start the water transmitter search manually later
on (for example when the water transmitter is lost or the batter-
ies are changed).
• Hold the CH button on the receiver for three seconds,"---" ap-
pears on the display, and the symbol is flashing.
• Insert new batteries into water transmitter and assemble it, then
it will transmit a signal to receiver.
• The receiver will the values from the water transmitter.
NOTE:
• After the water transmitter change the batteries, it must hold CH
button on the receiver 3 seconds in the corresponding channel (for
example if water transmitter is CH1, then hold CH button in 1 chan-
nel on receiver).it is for re-registration the water transmitter to re-
ceiver.
• If long time the receiver cannot display the transmitter values,
you can hold CH button for 3 seconds in corresponding channel to
search the transmitter.
• After you assemble the water transmitter the value of display
sometimes is -50.0 C or error, and also the receiver displays the
transmitter value error, it is not fault of the transmitter and receiv-
er, it will display correct value in few minutes. The reason is when
you assemble the PCB cover the sensor maybe not contact the pcb
good so the value is not correct, but after assemble the screw cov-
er, the sensor contact pcb good then the value will be correct.
7. Thermometer
• If the measure values above the range, then temperature dis-
play "HH.H". If the measure values below the range, then tempera-
ture display "LL.L".
7.1 Maximum/Minimum function
• Press the MAX/MIN button in normal mode, MAX appears on the
display.
• You can now get the highest values for the water and main unit
temperature since the last reset.
• Press the MAX/MIN button again, MIN appears on the display.
• You can now get the lowest values for the water and main unit
temperature since the last reset.
• Press the MAX/MIN button once more, to go back to the pres-
ent values display.
• The device will automatically quit the MAX/MIN mode if no but-
ton is pressed.
• Press CLEAR button while the maximum or minimum values are
displayed to clear the recorded readings.
7.2 Setting of the temperature unit
• In the normal mode you can change between °C (Celsius) or °F
(Fahrenheit) as temperature unit.
• Press the +/°C/°F button.
8. Additional water transmitters
• For having more than one additional water transmitter select with
the CH1/2/3 switch on the PCB (see fig. 6) for each single wa-
ter transmitter a different channel. The reception of the new trans-
mitter will be transmitted automatically to the receiver. Press and
hold the CH button on the receiver or restart the receiver accord-
ing to the manual.
• The water transmitter values will be shown on the display of
the receiver. If you have installed more than one water transmit-
ter, press the CH button on the receiver to change between the
channels 1 to 3.
• You can also choose an alternating channel display. After the third
channel, press the CH button again, The cycle display symbol
will be displayed.
• Press the CH button again to deactivate the alternating channel
and the first water transmitter will be shown permanently.
320281_vesilämpömittari_ko_EN_FI-SV-ET-LV-LT-RU.indd 3 320281_vesilämpömittari_ko_EN_FI-SV-ET-LV-LT-RU.indd 3
9. Positioning and fixing of receiver and the water transmitter
• With the foldable leg at the back of the receiver, the receiver can
be placed onto any flat surface or wall mounted at the respective
location by the hanging holes at the back of the unit. Avoid the vi-
cinity of any interfering field like computer monitors or TV sets and
solid metal objects.
• Check the transmission of the signal from the water transmitter
to the receiver (transmission range of up to 60 m free field). With-
in ferro-concrete rooms (basements, superstructures), the received
signal is naturally weakened.
10. Care And Maintenance
• Clean the devices with a soft damp cloth. Do not use solvents or
scouring agents.
• Remove the batteries if you do not use the products for a long
period of time.
• Keep the devices in a dry place.
10.1 Battery replacement
• Change the batteries of the water transmitter, when the battery
symbol appears on the display of the outdoor values.
• Change the batteries of the main unit, when the battery symbol
appears on the display of the main unit values.
• Please note: When the batteries are changed, the contact be-
tween pool transmitter and receiver must be restored, so always
insert new batteries into both devices or start a manual transmit-
ter search.
11. Troubleshooting
Problem
No indication at the receiver
No reception of the water
transmitter Indication "--" for
channel 1/2/3
Incorrect indication or low power
symbol display
12. Waste disposal
This product has been manufactured using high-grade materials
and components which can be recycled and reused.
Never dispose of empty batteries and rechargeable batteries in
household waste. As a consumer, you are legally required to take
them to your retail store or to an appropriate collection site de-
pending on national or local regulations in order to protect the en-
vironment.
This instrument is labelled in accordance with the EU Waste Electri-
cal and Electronic Equipment. Directive (WEEE).
Please do not dispose of this instrument in household waste. The
user is obligated to take end-of-life devices to a designated collec-
tion point for the disposal of electrical and electronic equipment, in
order to ensure environmentally-compatible disposal.
Hereby, Tarmo declares that the radio equipment type 320281 is in
compliance with Directive 2014/53/EU. The full text of the EU dec-
laration of conformity is available at the following internet address:
tammerbrands.eu/id/320281
Solution
Ensure that the batteries polari-
ties are correct
Change the batteries
No water transmitter is installed
Check batteries of external trans-
mitter (do not use rechargeable
batteries!)
Restart the water transmitter
and the main unit according to
the manual
Start the water transmitter
search manually according to
the manual
Reduce the distance between
the water transmitter and the
receiver
Check if there is any source of
interference
Change the batteries
12.8.2020 8.20.33 12.8.2020 8.20.33