Advertisement
PREPARING THE LAUNDRY
1. Check that all fastenings are closed and
that pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to
make sure it doesn't become tangled.
Sort laundry as follows:
A) By care symbols (on the collar or
inside seam):
Suitable for tumble drying
Tumble drying with reduced
drying intensity only. Press
Gentle button.
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds
dryer capacity, separate laundry
according to weight (e.g. towels from
thin underwear).
C) By type of fabrics
Cotton/linen: Towels, cotton jersey,
bed and table linen made of cotton or
linen.
Synthetics/Easy Care: Blouses, shirts,
overalls, etc. made of polyester or
polyamide, as well as cotton/synthetic
mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry: Woollens, silk, nylon
stockings, delicate embroidery, fabrics
with metallic decorations, bulky items such
as sleeping bags, etc.
Important: only use specific indicated
dryer-safe additives and rinse items
that have been treated with stain remover
thoroughly in plenty of water before
drying. Only use specific indicated
dryer-safe plastic items and never dry
rubber or articles contaminated with
vegetable oil in the dryer.
SELECTING A PROGRAMME & OPTIONS
Programme and Options:
•
To select a programme, turn the
programme selector knob to the
required position. The drying indicator
lamp is blinking, indicating that the
cycle needs to be started.
•
To select an option, press the
corresponding button. The indicator
light in the button lights up confirming
that the selection has been made.
•
Press the option button again to cancel
the option.
STARTING & COMPLETING A
PROGRAMME
1. Having selected the desired
programme and options, press the
Start/Pause button.
If the laundry is not removed at the
end of the drying cycle, an automatic
anti-crease cycle will operate for
maximum 60 min. The drum rotates at
regular intervals, preventing the
laundry from creasing.
Anti-Crease protection re-distributes
laundry in the drum.
2. On completion of the programme, set
the programme selector knob to
position "0".
CHANGING A PROGRAMME
When changing the programme during
the drying cycle, the dryer stops. The
drying indicator lamp is blinking.
To operate the new programme, press the
Start/Pause button.
INTERRUPTING A PROGRAMME
To interrupt the dryer during
operation
1. Set the programme selector knob to
Airing.
2. Press the Start/Pause button.
Wait at least 5 minutes before opening
the door to allow the dryer to cool
down.
For your safety the programme stops
automatically if you open the door.
3. To restart, after door opening, close
the door and press the Start/Pause
button again.
DAILY MAINTENANCE & CLEANING
Clean the lint filter at the end of every
drying cycle:
1. Open the door.
2. Pull the filter upwards.
3. Open the filter.
4. Remove lint using a soft brush or your
fingertips.
5. Close the filter.
6. Push the filter back into place.
Empty the water container at the end
of every drying cycle.
1. Pull the handle to remove the water
container.
2. Empty the water container.
3. Replace the water container when
empty by pushing it completely back
in place.
TROUBLESHOOTING GUIDE
If a fault occurs, before contacting our
After-Sales Service, make the
following checks to try and remedy
the problem:
Drying takes too long / laundry is not dry
enough:
•
Was the correct programme selected?
•
Was the inserted laundry too wet
(Washing machine spin speed less than
800 rpm? When the spinning speed is
less than 800 rpm the water container
fault may occur during the drying
cycle.)?
•
Is the lint filter dirty (filter indicator lamp
on)?
•
Is the heat exchanger dirty? (refer to
the Instructions for use)
•
Is the ambient temperature too high?
The dryer does not operate:
(after a power failure and/or
interruption to the mains supply,
always press the Start/Pause button).
•
Is the plug properly inserted into the
mains electricity socket?
•
Is there a power failure?
•
Has the fuse blown?
•
Is the door properly closed?
•
Has the programme been selected?
•
Has the Start/Pause button been
pressed?
Lint filter or water container indicator
lamp light on:
•
Is the lint filter clean?
•
Is the water container empty?
•
Is the water container correctly
positioned?
•
Is the heat exchanger clean?
Water droplets underneath the dryer:
•
Is the heat exchanger correctly
positioned?
•
Has any fluff on the heat exchanger
seal been wiped away?
•
Has any fluff on the door seal been wiped
away?
•
Has the water container been
positioned correctly?
AFTER-SALES SERVICE
If, after carrying out the above checks the
malfunction persists or appears again, turn
the dryer off and call our After-Sales
Service (refer to guarantee).
Please specify:
•
The nature of the fault.
•
The dryer type and model.
•
The service code (the number after the
word Service on the adhesive rating
plate) on the right-hand side when the
door is open.
•
Your full address and phone number.
5019 407 00438
Advertisement
