Related Manuals for RocwooD RWCM125
Summary of Contents for RocwooD RWCM125
- Page 1 CEMENT MIXER MODEL: RWCM125 RocwooD Instruction Manual NOTE: PLEASE READ INSTRUCTIONS CAREFULLY BEFORE USE.
-
Page 2: Safety Warnings & Instructions
SAFETY WARNINGS & INSTRUCTIONS SYMBOL AFFIXED TO THE MACHINE UNDERSTAND YOUR MIXER Read and understand the owner’s manual and labels affixed to the mixer. Learn its application and limitations as well as the specific potential hazards peculiar to it. Become familiar with the controls before operating this mixer. STAY ALERT Do not operate the mixer while under the influence of drugs, alcohol, or any medication that could affect your ability to use... - Page 3 SAFETY WARNINGS & INSTRUCTIONS SYMBOL AFFIXED TO THE MACHINE DRESS PROPERLY Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can be caught in moving parts. Protective electrically non-conductive gloves and non-skid footwear are recommended when working. Wear protective hair covering to contain long hair, preventing it from getting caught in machinery.
- Page 4 SAFETY WARNINGS & INSTRUCTIONS SYMBOL AFFIXED TO THE MACHINE DO NOT OVERREACH Keep proper footing and balance at all times when loading or unloading the mixer. Never stand on mixer. Serious injury could occur if the mixer is tipped or if the moving parts are unintentionally contacted. Do not store anything above or near the mixer where anyone might stand on the mixer to reach them.
-
Page 5: Table Of Contents
IP44D rated. Assembly and disassembly of the enclosure of electric control are critical SPECIFICATIONS to keep them remain effective. Only qualified electrician is Model Number RWCM125 allowed to repair the enclosure of electric control. Motor 550W S6 30% IP45D Double insulation... -
Page 6: Contents Of Shipping Container
CONTENTS OF THE SHIPPING CONTAINER ASSEMBLY INSTRUCTIONS Two people assist in assembly recommended. THE STAND... - Page 7 With a split pin inserted into the inner holes THE BOTTOM DRUM in each stub axle, place a flat washer, then a wheel followed by another flat washer. Insert another split pin into the axle holes outside each flat washer. Bend each side of the pins outward so they do not fall out.
- Page 8 Mount the mixing blades inside the bottom drum 2. Screw a M8X16 hex bolt with spring and flat loosely as shown - Two holes are provided at washers into each threaded hole in the the base of the drum into which a M8X20 bolt rim/ring gear.
-
Page 9: Operation Instructions
NOTE: The wheel must be allowed to pivot about the bolt so that the lugs on the bracket can be engaged or disengaged from the slots in the locking plate. THE TRANSMISSION CASE Lining up the keyways, slide the transmission case over the pinion shaft. - Page 10 The drum is locked in position by lugs on the Do not throw material into the self-locating tipping wheel which engage into mixer to avoid sticking firmly to the locking plate on the mixer frame. To tilt the the back of the drum. Trickle it drum, withdrawn the tipping wheel to dis-engage steadily over the ram.
-
Page 11: Maintenance Instructions
Do not pour or spray water directly WIRING DIAGRAM over the motor cover, especially the openings in it. Wipe off any external material on the motor cover. Do not use petrol, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products. -
Page 12: Parts Schematic
PARTS SCHEMATIC... - Page 13 PARTS LIST Description Q'ty Description Q'ty Cross Headed Screw M8X20 Bearing 6206 Waterproof Washer Drive Pinion Flat Washer 8 Lock Pin 6X45 Spring Washer 8 Sleeve Nut M8 Drive Shaft Mixing Blade Bearing 6202 Lower Drum Circlip 15 Big Cogwheel Circlip 42 Upper Drum Lock Nut M8...
Need help?
Do you have a question about the RWCM125 and is the answer not in the manual?
Questions and answers