Related Manuals for RocwooD RWCM63
Summary of Contents for RocwooD RWCM63
- Page 1 CEMENT MIXER MODEL: RWCM63 RocwooD Instruction Manual NOTE: PLEASE READ INSTRUCTIONS CAREFULLY BEFORE USE.
-
Page 2: Safety Warnings & Instructions
SAFETY WARNINGS & INSTRUCTIONS SYMBOL AFFIXED TO THE MACHINE UNDERSTAND YOUR MIXER Read and understand the owner’s manual and labels affixed to the mixer. Learn its application and limitations as well as the specific potential hazards peculiar to it. Become familiar with the controls before operating this mixer. STAY ALERT Do not operate the mixer while under the influence of drugs, alcohol, or any medication that could affect your ability to use... - Page 3 SAFETY WARNINGS & INSTRUCTIONS SYMBOL AFFIXED TO THE MACHINE DRESS PROPERLY Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can be caught in moving parts. Protective electrically non-conductive gloves and non-skid footwear are recommended when working. Wear protective hair covering to contain long hair, preventing it from getting caught in machinery.
- Page 4 SAFETY WARNINGS & INSTRUCTIONS SYMBOL AFFIXED TO THE MACHINE DO NOT OVERREACH Keep proper footing and balance at all times when loading or unloading the mixer. Never stand on mixer. Serious injury could occur if the mixer is tipped or if the moving parts are unintentionally contacted. Do not store anything above or near the mixer where anyone might stand on the mixer to reach them.
-
Page 5: Table Of Contents
IP44D rated. Assembly and disassembly of the enclosure of electric control are critical SPECIFICATIONS to keep them remain ef fective. Only qualified electrician is Model Number RWCM63 allowed to repair the enclosure of electric control. Motor 220W S6 30% 70 Litres Drum Capacity... -
Page 6: Contents Of Shipping Container
CONTENTS OF THE SHIPPING CONTAINER ASSEMBLY INSTRUCTIONS Two people assist in assembly recommended. THE STAND... - Page 7 With the frame lying on its side, attach the Carefully, and with two people, set the bottom support leg as shown. Insert a M8X60 hex drum with support arm onto the side supports bolt through the holes from one side, then of the stand as shown, so that the bearing flat washers and a lock nut from the other blocks slot into the channels provided by the...
- Page 8 THE UPPER DRUM THE TIPPING BAR Slide the locking plate over the large diameter shaft at the leg end of the frame with the rim facing inwards as shown. Secure with two M8X25 bolts, each with a flat washer and a Position the upper drum on bottom drum lock nut.
-
Page 9: Operation Instructions
Insert the spring into the bar pipe. Holding OPERATION INSTRUCTIONS it in place with a finger, place the bar over the larger diameter shaft so that the shaft retains the spring. Press down on bar until DRUM TILTING the holes in the bracket line up with the hole The spring-loaded tipping bar with locking lug drilled. -
Page 10: Maintenance Instructions
Thoroughly clean the mixer at the end of each LOADING day’s operation. Keep your mixer clean. The Completely unwind the extension slightest trace of material left in the drum will cord. Connect it to the concrete harden and attract more each time you use it mixer first before plugging in power until the machine is useless. -
Page 11: Wiring Diagram
The wiring diagram and parts WIRING DIAGRAM schematic in this manual are as reference tools only. Neither the manufacturer nor distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product or that he or she is qualified to replace any parts of the product. -
Page 12: Parts Schematic
PARTS SCHEMATIC... - Page 13 PARTS LIST Description Q'ty Description Q'ty Cross Headed Screw M8X16 Drive Shaft Waterproof Washer 8 Drive pinion Lock Nut M8 Lock Pin 5X40 Mixing Blade Circlip 20 Cross Headed Screw M6X16 Bearing 61804 Spring Washer 6 Bolt M3.5X16 Lock Nut M6 Belt Upper Drum Idle Pulley...
Need help?
Do you have a question about the RWCM63 and is the answer not in the manual?
Questions and answers