Subscribe to Our Youtube Channel
Related Manuals for AGCO 8200 Series
Summary of Contents for AGCO 8200 Series
- Page 1 Tractors 8200 Models 8210-8220-8240-8250-8260-8270-8280 AGCO - SA RC B562 104 539 July 2002 - Publication No. 3378 344M1 Beauvais - France Massey Ferguson est une filiale d’AGCO Corporation...
- Page 2 OPERATOR INSTRUCTION BOOK CONTENT TRACTOR IDENTIFICATION INTRODUCTION - SAFETY PRECAUTIONS AND WARRANTY INSTRUMENTS AND CONTROLS OPERATION MAINTENANCE AND ADJUSTMENTS SPECIFICATIONS ACCESSORIES AND OPTIONS TROUBLESHOOTING ELECTRIC EQUIPMENT Find manuals at https://best-manuals.com...
- Page 3 OPERATOR INSTRUCTION BOOK OPERATOR’S GENERAL CHAPTER 1 - TRACTOR IDENTIFICATION ..........1-1 1.1 - SERIAL NUMBER ..........................1-5 CHAPTER 2 - INTRODUCTION-SAFETY PRECAUTIONS AND WARRANTY ..................2-1 2.1 - INTRODUCTION ..........................2-5 2.1.1 - inspection before delivery, service entry on the user’s premises and guarantee ....2-5 2.1.2 - Inspection before delivery, service entry on the user’s premises and guarantee ....
- Page 4 OPERATOR INSTRUCTION BOOK 2.12 - SAFETY - AFTER OPERATION ......................2-14 2.12.1 - Make the right moves ......................2-14 2.12.2 - Follow safe operating practices ..................2-14 2.12.3 - Watch out for others ......................2-14 2.12.4 - Risk of overturning ......................2-15 2.12.5 - To avoid rear overturns .......................
- Page 5 OPERATOR INSTRUCTION BOOK 4.1 - BREAK IN ............................4-5 4.1.1 - The following precautions should be taken during the break in period ........ 4-5 4.2 - STARTING ............................4-5 4.2.1 - Starting the engine ....................... 4-5 4.3 - STOPPING THE ENGINE ........................4-6 4.4 - DRIVING THE TRACTOR ........................
- Page 6 OPERATOR INSTRUCTION BOOK 4.13.3 - Remote outlets ........................4-23 4.13.4 - Bosch SB23 electrohydraulic spool valves ................. 4-24 4.13.5 - Emergency manual control of the spool valves ..............4-24 4.13.6 - Memorisation of the joystick (Fig. 34) ................4-25 4.14 - THREE-POINT LINKAGE ......................... 4-26 4.14.1 - Implement installation .......................
- Page 7 OPERATOR INSTRUCTION BOOK 5.7.1 - Grease the following ......................5-12 5.8 - ENGINE ............................5-15 5.8.1 - 6 cylinder engine 8210/8220 ....................5-15 5.8.2 - 6 cylinder engine 8270/8280 ....................5-15 5.8.3 - Check the engine oil level every ten hours or daily ............5-16 5.8.4 - Change the engine oil every 300 hours ................
- Page 8 OPERATOR INSTRUCTION BOOK 5.18 - WHEELS ............................5-30 5.19 - TRACK ADJUSTMENTS ......................... 5-30 5.19.1 - FRONT TRACK ........................5-30 5.19.2 - Pressed steel wheels ......................5-31 5.20 - REAR TRACK ADJUSTMENT ......................5-33 5.20.1 - Settings obtained ........................ 5-33 5.20.2 - Changing the position of the wheel on the shaft ...............
- Page 9 OPERATOR INSTRUCTION BOOK 6.5 - TRANSMISSION ..........................6-10 6.6 - FINAL REDUCTION UNITS ......................6-11 6.7 - POWER TAKE-OFF .......................... 6-11 6.8 - FOUR-WHEEL DRIVE FRONT AXLE ....................6-11 6.9 - HYDRAULICS ........................... 6-11 6.9.1 - Closed center hydraulic system with flow and pressure control ........6-11 6.10 - HYDRAULIC LIFT ..........................
- Page 10 OPERATOR INSTRUCTION BOOK 7.4 - GLOSSARY ............................7-20 7.5 - FRONT DUAL CONTROL ........................ 7-21 7.5.1 - General ..........................7-21 7.5.2 - Description of the adjustment screen ................7-21 7.5.3 - Settings ..........................7-21 7.5.4 - Use (Fig. 25) ........................7-22 7.6 - TRAILED IMPLEMENT CONTROL (T.I.C) ..................
- Page 11 1.TRACTOR IDENTIFICATION CHAPTER 1 - TRACTOR IDENTIFICATION...
- Page 13 1.TRACTOR IDENTIFICATION CONTENT 1.1 - SERIAL NUMBER ..........................1-5...
- Page 15 1.1 - SERIAL NUMBER Homologation plates (according to countries). IMPORTANT : NOTE THE SERIAL NUMBER OF YOUR TRACTOR. ALWAYS QUOTE THE SERIAL NUMBER IN ANY COMMUNICATION WITH YOUR AGCO DEALER. Manufacturer plate with serial number (according to countries). V 558 V 557...
- Page 16 1.TRACTOR IDENTIFICATION Engine serial number Powershift Gearbox serial number Fig. E V 464 V 648 Front axle Serial number V 438 Fig. C V 437 Fig. F Serial number MODEL ______________________________________ SERIAL NO ___________________________________ ENGINE SER. NO _____________________________ OWNER’S NAME & ADDRESS (IF AVAILABLE) _____________________________________________ _____________________________________________ _____________________________________________...
- Page 17 2. INTRODUCTION - SAFETY PRECAUTIONS AND WARRANTY CHAPTER 2 - INTRODUCTION - SAFETY PRECAUTIONS AND WARRANTY...
- Page 19 2.INTRODUCTION - SAFETY PRECAUTIONS AND WARRANTY CONTENT 2.1 - INTRODUCTION ..........................2-5 2.1.1 - inspection before delivery, service entry on the user’s premises and guarantee ....2-5 2.1.2 - Inspection before delivery, service entry on the user’s premises and guarantee ....2-6 2.1.3 - Guarantee procedure ......................
- Page 20 2.INTRODUCTION - SAFETY PRECAUTIONS AND WARRANTY 2.12.10 - Road transport ........................2-19 2.12.11 - Rules of the road ........................ 2-19 2.13 - SAFETY - AFTER OPERATION ......................2-2...
- Page 21 This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...
Need help?
Do you have a question about the 8200 Series and is the answer not in the manual?
Questions and answers