Advertisement
This issue should not apply to Windows 2000 or Windows NT 4.0.
PROBLEM:
My software isn't recognizing my modem.
Make sure that your phone cord is properly connected. Remove the phone
Your communications software may not function properly if you
cord from the modem and wall jacks. Clean any dirt or corrosion from the
have more than one version of the software installed, you are using
cord and jacks. Reinsert the cord securely in the modem's line jack and
an older version, or you have more than one communications
the wall jack. Use the phone cord included with your modem, if possible.
application installed on your system. We highly recommend using
the communications software provided with your modem on the
Installation CD-ROM.
Make sure that your internal modem is physically installed correctly in
your computer. You will need to press the modem in firmly so that it is
Your software's COM port settings may be incorrect. There should
seated properly in its slot. When the modem is installed correctly, you will
be a place in the Setup section of your software that addresses
no longer see any part of the gold edge. See the front of this guide for
port settings. Make sure the software's port settings match those
complete instructions. If your modem still does not work, turn off your
for your modem. To check which COM port your modem is using,
click Windows Start, Settings, and Control Panel. Double-click
computer, remove the modem, and reinstall it in another PCI slot.
Modems, select your modem, and select Properties. Check
your communication software's documentation for instructions on
adjusting the port settings in your software.
PROBLEM:
My computer isn't recognizing my modem.
If you are using software which uses Windows' modem description
and you had a previous modem installed, you may need to update
your software's setting to reflect the use of the U.S. Robotics 56K
PCI Software Modem.
If Plug and Play fails to find the modem as new hardware, you need to
check the following:
• Confirm that the modem is firmly seated in the PCI slot. The modem
If you are using Windows-based software which has its own list of
should sit evenly in the slot with no part of the gold edge showing.
modems to select from, you may need to update the software for
• Try installing the modem in another PCI slot.
use with this modem. For best operation, please select Standard
• Check your computer manual to make sure that the PCI slot is configured
Modem or Hayes Compatible from the list of manufacturers.
properly.
You may also need to select the modem's COM port. Select the
COM port which corresponds to the COM port assigned to the
modem in the Control Panel, under the Modems icon in the
You will need to run a setup program for Windows NT 4.0. Download the
Diagnostics tab. Click on Windows Start, Settings, and Control
support drivers at www.usr.com/support.com.
Panel. When Control Panel opens, click Modems. You will see
a list of installed modems.
PROBLEM:
My modem seemed to install correctly but won't work.
If you are using Dial-Up Networking, Dial-Up Networking may not
be configured correctly. Check your configuration and make sure
you have the correct modem selected. Double-click My Computer,
An IRQ may need to be properly assigned to your modem.
double-click Dial-Up Networking, right-click the connection you
are trying to use, and click Properties. Make sure that the
description in the modem box reads U.S. Robotics. If not, please
Right-click the My Computer icon on your desktop. Click Properties,
select this modem.
and then click the Device Manager tab. In the list of devices, locate the
Modem category. Look for your modem's description. If a yellow exclamation
point appears over the modem's description, your modem is in conflict with
PROBLEM:
another device.
My modem won't dial out or doesn't answer
• Try installing the modem in another PCI slot.
• Check your computer manual to make sure that the PCI slot is configured
incoming calls.
properly.
• If an available IRQ does not exist, you may need to remove, disable, or
relocate another device. Refer to that device's documentation for more
information about removing, disabling, or relocating it.
You may have a bad phone cord connection to your modem, or
your phone cord may be plugged into the wrong jack. The phone
cord should be plugged into the LINE jack on the modem and into
Turn off your computer and physically remove the modem. Restart your
the wall jack. Use the phone cord included in your modem's box,
computer, and check for an available IRQ by clicking Windows Start,
if possible.
Programs, Administrative Tools, and Windows NT Diagnostics. Click
the Resources tab and select IRQ. Take note of an available IRQ that your
modem can use. If there are no IRQs available, you may have to remove,
You may have devices between the modem and the phone jack.
disable, or relocate another device in order to free an IRQ for use by your
There should be no line splitters, fax machines, or other devices
modem. Refer to that device's documentation for more information about
between the modem and the wall jack.
removing, disabling, or relocating it. If you do have an available IRQ, but it
isn't being assigned to the modem, you may need to try the modem in
another PCI slot, or check with your computer manufacturer to ensure your
PCI slots are configured correctly.
You may have plugged your modem's phone cord into a digital
line. This will cause permanent damage to your modem. Contact
PROBLEM:
the department responsible for your phone system if you are unsure
whether or not your phone line is digital.
My modem appeared to install correctly, but seems
to be performing erratically.
If your phone system requires dialing "9" to access an outside
line, be sure to add "9" before the number you are dialing.
Although PCI devices can share IRQs, there are devices on the market
which do not share IRQs properly. If the modem has been assigned to an
IRQ with one of these devices, the modem may perform erratically.
If you have voice mail provided by your local phone company, your
dial tone may be altered when messages are waiting. Retrieve
your voice mail to restore your normal dial tone.
Right-click the My Computer icon on your desktop. Click Properties,
and then the Device Manager tab. Double-click the Computer icon at
PROBLEM:
the top of the device list. You will see a listing of your system's IRQs and
My modem sounds like it's trying to connect
the devices to which they are assigned. Locate your modem and the IRQ
to another modem but fails.
which it is assigned. If this IRQ is being used by any other devices, it may
be causing the modem not to work properly. Either your modem or the
device which shares an IRQ with your modem will have to be reassigned to
another IRQ in order to resolve your conflict. You may want to try installing
You may have a poor connection. All calls are routed differently, so
the modem in another PCI slot, or refer to the sharing device's documentation
try placing the call again.
for more information about removing, disabling, or relocating it.
PROBLEM:
My modem isn't achieving a 56K Internet
(801) 401-1141
connection.
8:00 A.M. – 7:00P .M. CST Monday-Friday
U.S. Robotics also staffs its own fee-based 900 number for
Due to current FCC regulations, maximum download speed is
immediate assistance. These lines are staffed from:
limited to 53,333 bps.
No-Hold line (900) 555-USR1
Our research has shown that the vast majority of telephone lines in
8:00 A.M. – 7:00 P.M. CST Monday-Friday
North America can and do support V.90 connections. The V.90
9:00 A.M. – 5:00 P.M. CST Saturday-Sunday
protocol allows for connection speeds of up to 56K, but line conditions
For a no hold call, a $2.50 per minute charge (price subject to
may affect the actual speeds during a given connection. Due to
change without notice) will appear on your local phone bill. You
unusual telephone line configurations, some users will not be able to
must be 18 or older or have parental permission. (Service available
take full advantage of V.90 technology at this time. In order to achieve
in the U.S. only)
a V.90 connection:
Canada:
• The server you're dialing in to must support and provide a digital
(801) 401-1145
V.90 signal. Your ISP can provide you with a list of dial-up
8:00 A.M. – 7:00 P.M. CST Monday-Friday
connections and information on what those connections currently
support.
• The telephone line between your ISP and your modem must be
capable of supporting a 56K connection and contain only one
We declare under our sole responsibility that the U.S. Robotics 56K* PCI Software Modem,
analog-to-digital conversion. The 56K signal from your ISP begins
to which this declaration relates, is in conformity with the following standards or other
as a digital signal. Somewhere between the ISP and your modem,
normative documents:
there will be a digital-to-analog signal conversion so that your
Emmisions:
modem can receive the data. There must be no more than one
Safety:
analog-to-digital signal conversion in the path from your ISP to
Telecom:
your modem. If more than one analog-to-digital conversion occurs,
FCC Class B Certification
your connect speeds will default to V.34 (33.6 Kbps). There may
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
also be impairments on the local lines between your ISP and your
conditions:
1.
This device may not cause harmful interference, and
modem. These impairments can prevent or limit V.90 connection
2.
This device must accept any interference received, including interference that may
speeds. All telephone calls are routed differently, so you should
cause undesired operation.Warning! This equipment has been tested and found to comply
try making your 56K connection several times. One way to test
with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
this is to dial into a long distance location. Long distance lines are
limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency
often much clearer than local lines. It is important to note that
energy and, if not installed and used in accordance with the instructions, may cause harmful
telephone companies are constantly upgrading their systems.
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
Lines that do not support 56K today may support 56K in the near
radio or television reception, which can be determined by turning the equipment off and on,
future.
the user is encouraged to try to correct the interference by one or more of the following
• Your modem must be connecting to a V.90/56K server. A pair of
measures:
Reorient or relocate the receiving antenna.
56K modems will not connect to each other at V.90/56K speeds.
Increase the distance between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from the one which the
receiver is connected to.
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
Should you need to perform an uninstall of your modem, refer to
the following steps:
Attach standard telephone cable to the RJ-11 port.
Note: In order to maintain compliance with the limits of a Class B digital device, US Robotics
requires that you use a quality interface cable when connecting to this device. Changes or
modifications not expressly approved by US Robotics could void the user's authority to
• Select Start.
operate this equipment. Suggested cable type is 90-ohm USB cable for the USB port, and
• Select Settings.
standard telephone cable for the RJ-11 port.
• Select Control Panel.
• Double-click Add/Remove Programs.
Manufacturer's Disclaimer Statement
• Select U.S. Robotics 56K PCI Software Modem.
• Click Add/Remove.
The information in this document is subject to change without notice and does not represent a
commitment on the part of the vendor. No warranty or representation, either expressed or
• Click Yes.
implied, is made with respect to the quality, accuracy or fitness for any particular purpose of
• Click OK to close.
this document. The manufacturer reserves the right to make changes to the content of this
document and/or the products associated with it at any time without obligation to notify any
person or organization of such changes. In no event will the manufacturer be liable for direct,
indirect, special, incidental or consequential damages arising out of the use or inability to use
this product or documentation, even if advised of the possibility of such damages. This
• Select Start.
document contains materials protected by copyright. All rights are reserved. No part of this
manual may be reproduced or transmitted in any form, by any means or for any purpose
• Select Settings.
without expressed written consent of its authors. Product names appearing in this document
• Select Control Panel.
are mentioned for identification purchases only. All trademarks, product names or brand
• Double-click System.
names appearing in this document are the property of their respective owners.
• Select the Hardware tab.
Canadian Notice
• Click Device Manager.
This digital apparatus does not exceed the Class B limits for radio noise emissions from
• Select U.S. Robotics 56K PCI Software Modem.
digital apparatus set out in the Radio Interference Regulations of Industry Canada. ICES-003
• Left-click and select Uninstall.
Le présent appareil numérique n'émet pas de bruits radio-électriques dépassant les limites
applicables aux appareils numériques de la classe B prescrites dens le Règlement sur le
brouillage radioélectrique édicté par l'Industrie. NMB-003
To ensure that certified equipment is attached correctly and only to the networks of
participating carriers, the following statement shall accompany each unit of certified
equipment offered for sale. This statement must be included conspicuously in written or
If you have not fixed a problem after trying the suggestions in the
electronic format, at or near the front of each copy of the operating manual, or accompany
Troubleshooting section, you can receive additional help via one of
other technical information, or be included as a separate sheet. The required statement is:
these convenient resources:
NOTICE: The Industry Canada label identifies certified equipment. This certification means
that the equipment meets telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
documents(s). The department does not guarantee the equipment will operate to the user's
satisfaction."
Before installing this equipment, users should ensure that it is permissible to be connected to
the facilities of the local telecommunications company. The equipment must also be installed
Contains useful product information, documents, and manuals. Log
using an acceptable method of connection. The customer should be aware that compliance
with the above conditions might not prevent degradation of service in some situations.
on to:
Repairs to certified equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to
http://www.usr.com/support/
disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas. Caution:
The dealer may be able to troubleshoot the problem over the
Users should not attempt to make such connections themselves, but should contact the
phone or may request that you bring the modem back to the
appropriate electric inspection authority, or electrician, as appropriate.
store for service.
An explanatory note on Ringer Equivalence Numbers (see Section 10.0) and their use must
be provided for the terminal equipment user in the information accompanying the terminal
equipment. A notice similar to the following would be suitable:
Technical questions about U.S. Robotics modems can also be
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides
an indication of the maximum number of terminals allowed to be connected to a telephone
answered by technical support specialists. Be sure to have your
interface. The termination on an interface may consist of any combination of devices
serial number and your model number readily available. Your model
subject only to the requirement that the sum of the ringer equivalence Numbers of all the
number is 5600.
devices does not exceed 5.
Canadian Modem Users, your warranty and repair center is:
Richmond, B.C. Canada V6V 2G9
U.S. Robotics Corporation Limited Warranty
HARDWARE: U.S. Robotics warrants to the end user ("Customer") that this hardware product will be
free from defects in workmanship and materials, under normal use and service, for the following
length of time from the date of purchase from U.S. Robotics or its authorized reseller:
U.S. Robotics sole obligation under this express warranty shall be, at U.S. Robotics option and
expense, to repair the defective product or part, deliver to Customer an equivalent product or part to
replace the defective item, or if neither of the two foregoing options is reasonably available, U.S.
Robotics may, in its sole discretion, refund to Customer the purchase price paid for the defective
product. All products that are replaced will become the property of U.S. Robotics. Replacement
products may be new or reconditioned. U.S. Robotics warrants any replaced or repaired product or
part for ninety (90) days from shipment, or the remainder of the initial warranty period, whichever is
longer.
SOFTWARE: U.S. Robotics warrants to Customer that each software program licensed from it will
perform in substantial conformance to its program specifications, for a period of ninety (90) days
from the date of purchase from U.S. Robotics or its authorized reseller. U.S. Robotics warrants the
media containing software against failure during the warranty period. No updates are provided. U.S.
Robotics sole obligation under this express warranty shall be, at U.S. Robotics option and expense,
to refund the purchase price paid by Customer for any defective software product, or to replace any
defective media with software which substantially conforms to applicable U.S. Robotics published
specifications. Customer assumes responsibility for the selection of the appropriate applications
program and associated reference materials. U.S. Robotics makes no warranty or representation that
its software products will meet Customer's requirements or work in combination with any hardware or
applications software products provided by third parties, that the operation of the software products
will be uninterrupted or error free, or that all defects in the software products will be corrected. For any
(U.S.) FCC Part 15 Class B, (Canada) ICES-003
third-party products listed in the U.S. Robotics software product documentation or specifications as
(U.S.) UL 1950, 3rd Edition, (Canada) C.22.2.950
being compatible, U.S. Robotics will make reasonable efforts to provide compatibility, except where
(U.S.) FCC Part 68, (Canada) Industry Canada (CS-03)
the noncompatibility is caused by a "bug" defect in the third party's product or from use of the
software product not in accordance with U.S. Robotics published specifications or User Guide.
THIS U.S. ROBOTICS PRODUCT MAY INCLUDE OR BE BUNDLED WITH THIRD-PARTY
SOFTWARE, THE USE OF WHICH IS GOVERNED BY A SEPARATE END-USER LICENSE
AGREEMENT. THIS U.S. ROBOTICS WARRANTY DOES NOT APPLY TO SUCH THIRD-PARTY
SOFTWARE. FOR THE APPLICABLE WARRANTY, PLEASE REFER TO THE END-USER LICENSE.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas. Caution: Users should not attempt to make
such connections themselves, but should contact the appropriate electric inspection authority, or
electrician, as appropriate.
An explanatory note on Ringer Equivalence Numbers (see Section 10.0) and their use must
be provided for the terminal equipment user in the information accompanying the terminal
equipment. A notice similar to the following would be suitable:
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the ringer equivalence Numbers of
all the devices does not exceed 5.
Canadian Modem Users, your warranty and repair center is:
Richmond, B.C. Canada V6V 2G9
AGREEMENT GOVERNING THE USE OF SUCH SOFTWARE.
U.S. Robotics shall not be responsible for any software, firmware, information,
or memory data of Customer contained in, stored on, or integrated with any
products returned to U.S. Robotics for repair, whether under warranty or not.
OBTAINING WARRANTY SERVICE: Customer must contact a U.S. Robotics Corporate Service
Center or an Authorized U.S. Robotics Service Center within the applicable warranty period to
obtain warranty service authorization. Dated proof of purchase from U.S. Robotics or its
authorized reseller may be required. Products returned to U.S. Robotics Corporate Service Center
must be pre-authorized by U.S. Robotics with a Service Repair Order (SRO) number marked on
the outside of the package, and sent prepaid and packaged appropriately for safe shipment, and it
is recommended that they be insured or sent by a method that provides for tracking of the
package. The repaired or replaced item will be shipped to Customer, at U.S. Robotics expense, not
later than thirty (30) days after U.S. Robotics receives the defective product. Return the product
to:
WARRANTIES EXCLUSIVE: IF A U.S. ROBOTICS PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY FOR BREACH OF THAT WARRANTY
SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT U.S.
ROBOTICS OPTION. TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, TERMS, OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY
OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS,
OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
SATISFACTORY QUALITY , CORRESPONDENCE WITH DESCRIPTION, AND NON-
INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. U.S. ROBOTICS NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF
ITS PRODUCTS. U.S. ROBOTICS SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS
TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN
THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD
PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING , UNAUTHORIZED
ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE
BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE,
LIGHTNING, OTHER HAZARDS, OR ACTS OF NATURE.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, U.S. ROBOTICS ALSO
EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY , WHETHER BASED IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL,
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE
OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS,
EVEN IF U.S. ROBOTICS OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT,
OR REFUND OF THE PURCHASE PRICE PAID, AT U.S. ROBOTICS OPTION. THIS
DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY
PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
DISCLAIMER: Some countries, states, or provinces do not allow the exclusion or limitation of
implied warranties or the limitation of incidental or consequential damages for certain products
supplied to consumers, or the limitation of liability for personal injury, so the above limitations and
exclusions may be limited in their application to you. When the implied warranties are not allowed to
be excluded in their entirety, they will be limited to the duration of the applicable written warranty.
This warranty gives you specific legal rights which may vary depending on local law.
GOVERNING LAW: This Limited Warranty shall be governed by the laws of the State of Illinois,
U.S.A. excluding its conflicts of laws principles and excluding the United Nations Convention on
Contracts for the International Sale of Goods.
U.S. Robotics Corporation
Unit – 100, 13751 Mayfield
Twelve (12) months
U.S. Robotics Corporation
Unit – 100, 13751 Mayfield
In The United States:
USR-Walnut
528 Spanish Lane
Walnut, CA 91789
Advertisement
