Juniper JOT Desk BL-6 General Installation Manual

U-shape workstation

Hide thumbs

Table Of Contents

Quick Links

Download this manual

BL-6

JOT Desk

U-Shape Workstation

Includes Add-Ons:

A1 | A2 | A3 | A4

General Installation Guide

Table of Contents

Summary of Contents for Juniper JOT Desk BL-6

Page 1 BL-6 JOT Desk U-Shape Workstation Includes Add-Ons: A1 | A2 | A3 | A4 General Installation Guide...
Page 3: Table Of Contents
Edition Code :: JOT U-Shape ................1 BL-6-1 :: JOT U-Shape with 72” Surface ........7 BL-6-2 :: JOT U-Shape with Steel Storage ......15 BL-6-3 Add-ons :: Surface-Mount Cable Management Tray ....23 :: Modesty Panel ................27 :: Laminate Inset End Panels ............ 31 :: Steel Inset End Panels ............
Page 4: Bl-6-1 :: Jot U-Shape
Workstation with 54" W Bridge Surface or Smaller Overview JOT U-Shape Workstation All parts listed are for a U-Shape workstation; additional parts will be needed for additional U-Shape workstations.
Page 5 Parts List Code Qty. Description GBXXXX Main Surface GBXXXX Bridge Surface Long Beam Lock Plate BLPB2 Cap Screw Locking Screw and Lever 30” End Leg BL30 Wood Screws 24” End Leg BL24 Wood Screws 1 or 3 42” Support Bar* BASB72 Wood Screws BFB1...
Page 6 1 | Join Main Surface 30” End Legs with Beam Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring that there is not a gap between beam and legs. Using a rubber mallet, hammer beam to lock in place. 2 | Bolt Down Beam-to-Leg Lock Plate Note: Beam lock plates will not fit if there is a gap between beam and leg.
Page 7 3 | Measure and Adjust Beam Width Measure from end leg to end leg until you find the approximate width of work surface. Insert the screw through overlapping beam slots and into locking screw and lever. Slightly tighten screw. DO NOT fully tighten.
Page 8 5 | Secure Support Hardware to Main Surface for Bridge Surface Using wood screws for each flat brackets secure brackets to edge of main surface with half of brackets extended over edge of surface. Using wood screws, secure support bar to underside of surface centered between flat brackets.
Page 9 7 | Attach Second Workstation to Bridge Align second workstation with return so that back edge is flush. Secure flat brackets with wood screws into underside of both surfaces. Insert final wood screws and tighten beam locks. 8 | 9 | Secure Extra Support Bars NOTE: Support bars will be added to surfaces 72”...
Page 10: Bl-6-2 :: Jot U-Shape With 72" Surface
Workstation with 60” W or Longer Bridge Surface Overview JOT U-Shape Workstation All parts listed are for a U-Shape workstation; additional parts will be needed for additional U-Shape workstations.
Page 11 Parts List CODE Description GBXXXX Main Surface GBXXXX Bridge Surface Extra Long Beam Lock Plate & BBC1 Cap Screw Locking Screw and Lever BLPB2 Long Low Profile Beam 30” End Leg BL30 Wood Screws 24” End Leg BL24 Wood Screws 42”...
Page 12 1 | Join Main Surface 30” End Legs with Beam Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring that there is not a gap between the beam and legs. Using a rubber mallet, hammer beam to lock in place. 2 | Bolt Down Beam-to-Leg Lock Plate Note: Beam lock plates will not fit if there is a gap between beam and leg.
Page 13 3 | Measure and Adjust Beam Width Measure from end leg to end leg until you find the approximate width of work surface. Insert screw through overlapping beam slots and into locking screw and lever. Slightly tighten screw. DO NOT fully tighten.
Page 14 5 | Secure First Surface Position surface on frame. Align outer sides of surface flush and parallel with outer sides of end legs. Adjust beam positions if sides are not flush. Fasten surface to frame with wood screws through leg brackets into underside of surface. Align Flush Align Flush 6 | Secure Second Surface...
Page 15 7 | Secure Bridge Surface Secure flat brackets to edge of each surface, facing towards inside of workstation, with half of brackets extended over edge surface. Place final surface over exposed beam and align with back edge of workstation and secure with wood screws to flat brackets.
Page 16 9 | Secure Support Bars NOTE: Support bars will be added to surfaces 72” and longer. Place support bars as shown below and secure to underside of surface using wood screws.
Page 18: Bl-6-3 :: Jot U-Shape With Steel Storage
Workstation with Steel Storage Overview JOT U-Shape Workstation All parts listed are for a U-Shape workstation with steel storage; additional parts will be needed for additional U-Shape workstations with steel storage.
Page 19 Parts List Code Qty. Description GBXXXX Main Surface GBXXXX Bridge Surface Extra Long Beam Lock Plate Cap Screw Locking Screw and Lever 30” End Leg BL30 Wood Screws 1 or 2 42” Support Bar* BASB72 Wood Screws BFB1 Flat Bracket BLLF42 Steel Lateral Storage *Support bars will be added to surfaces 72”...
Page 20 1 | Join Main Surface End Legs with Beam Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring that there is not a gap between the beam and legs. Using a rubber mallet, hammer the beam to lock in place. 2 | Bolt Down Beam-to-Leg Lock Plate Note: The beam lock plates will not fit if there is a gap between the beam and the leg.
Page 21 3 | Measure and Adjust Beam Width Measure from end leg to end leg until you find the approximate width of the work surface. Insert the screw through the overlapping beam slots and into the locking screw and lever. Slightly tighten the screw. DO NOT fully tighten.
Page 22 5 | Secure Support Hardware to Main Surface for Bridge Surface Using wood screws for each flat brackets secure brackets to edge of main surface with half of brackets extended over edge of surface. Using wood screws, secure support bar to underside of surface centered between flat brackets. 6 | Attach Bridge to Main Surface Align return surface with main surface and secure flat plates and supported bar with wood screws into underside of surface.
Page 23 7 | Secure Second Surface to Leg Assemble second surface by securing 24” leg to underside of laminate surface with wood screws. 8 | Place Storage and Desk in Position Place second surface with leg on top of steel storage and align front and side edges of surface flush with storage piece.
Page 24 9 | Secure L-Shape Workstation to Steel Storage Surface Align assembled L-Shape workstations with steel storage surface so that the back edge is flush. Secure the flat brackets with wood screws into the underside of both surfaces. Align Flush...
Page 25 10 | Tighten Beam Locks 11 | Secure Support Bar NOTE: Support bars will be added to surfaces 72” and longer. Place support bar as shown below and secure to underside of surface using wood screws.
Page 26: A1: Surface-Mount Cable Management Tray
A1: Surface-Mount Cable Management Tray Overview JOT L-Shape Workstation If workstations have power, refer to JOT power guide.
Page 27 Parts List Code Qty. Description Surface-Mount Cable Management Tray BHCT Wood Screws...
Page 28 1 | Extend Cable Tray to Desired Length Extension range: 25”–45”.
Page 29 2 | Attach Cable Tray to Surface Attach cable tray using wood screws.
Page 30: A2: Modesty Panel
A2: Modesty Panel Overview Jot L-Shape Workstation All parts listed are for a single modesty panel; additional parts will be needed for additional modesty panels.
Page 31 Parts List Code Qty. Description Laminate Modesty Panel* GLMP## Machine Screws L-Brackets BMPBFB Wood Screws *For Steel Modesty Panel: components may vary, but process is similar.
Page 32 1 | Secure Brackets to Modesty Panel Connect bracket to modesty panel using screws. Secure tightly.
Page 33 2 | Attach Modesty Panel to Surface Attach modesty panel to surface using wood screws provided with brackets. Panel will be center aligned and flushed with back of surface.
Page 34: A3: Laminate Inset End Panels
A3: Laminate Inset End Panels Overview JOT L-Shape Workstation All parts listed are for a single panel; additional parts will be needed for additional panels.
Page 35 Parts List Code Qty. Description GBEP## Laminate Inset End Panel End Panel T-Bracket LEPBL1 Self-Tapping Screws Wood Screws...
Page 36 1 | Secure Bracket to End Legs Attach 4 brackets to each end leg using self-tapping screws. 1. Inset–Back of bracket will align flush with edge of leg. 2. Flush–Back of bracket will be 9/16” from edge back edge of leg. Inset Bottom View Align Flush "...
Page 37 2 | Attach End Panel Slide end panels into place and adjust until flush with bracket. Use wood screws to secure panel to each bracket.
Page 38: A4: Steel Inset End Panels
A4: Steel Inset End Panels Overview JOT L-Shape Workstation All parts listed are for a steel inset end panel; additional parts will be needed for additional steel inset end panels.
Page 39 Parts List Code Qty. Description Steel Inset End Panel BEP## Self-Tapping Screws...
Page 40 1 | Secure Panels to End Legs Slide the end panel into place and adjust until either flush with outside of leg or slightly recessed. Align Flush Slightly Recessed...
Page 41 2 | Attach End Panel Use 4-6 self-tapping screws to secure panel to each leg.

Juniper JOT Desk BL-6 General Installation Manual

Quick Links

Related Manuals for Juniper JOT Desk BL-6

Summary of Contents for Juniper JOT Desk BL-6