Table of Contents
Advertisement
r
SPECIFICATIONS
Amplifier Section
Continuous power ouiput
{both channels driven at 20 Hz to 20 kHz}*
T.H.D. 0.07 %, 82
35W+35W
T.H.D.0.1%,4Q..
40 W +40 W
DIN Continuous power output (both channels driven at 1 kHz}
TH
DE 130-96,
B90).22t. cs coast
hip dra
ered 45W+45W
T.H.D.10%,42
55 W+55W
Dynamic power output (E.L.A. test signal)
Total harmonic distortion*
20 Hz to 20 KHZ, 17.5 W, 8 Q onc cceeceeseeeeteeeeeeenes 0.05 %
Input sensitivity/ impedance
PHONO (MIM) vicssseseorecescostiatasevacsstvvieresensivananee 2.8 mV/ 50 kQ
CD, TUNER, LINE, TAPE 1/DAT, TAPE
2 MONITOR
a
Wes ngitate sabe Sdtehvodesetaedaeieecese catatesebuasudstesh debeiusedeous 200 mV/ 50 kQ
PHONO overload level
VG A2 0D
O51 8G (MM) aati
tra ca deattiedetal teat 150 mV
Output level/ impedance
TAPE 1/DAT, TAPE 2 MONITOR o....cccccceeeeees 200 mV/ 1 kQ
Frequency response
PHONO (MM)... ceseeestesessceneeteeeenees 20 Hz to 20 kHz
+ 0.5 dB
CD, TUNER, LINE, TAPE 1/DAT, TAPE 2 MONITOR
.5 Hz to 100kHz °3dB
Signal -to-Noise ratio (IHF short circuit, A network}
PHONO (MM, 5 mV input) ..
CD, TUNER, LINE, TAPE 1/DAT, TAPE 2 MONITOR...
Signal-to-Noise ratio (DIN, continuous power/ 50 mW)
PHONO (MM)
. 70 dB/ 64 6B
CD, TUNER, LINE, TAPE 1/DAT, TAPE 2 MONITOR
88 dB/ 67 dB
82dB
107 dB
Power Supply/ Miscellaneous
Power requirements
UL Kod ell: ...5ctsieuveraiiec
odin AC 230 Volts, 50/60 Hz
Round 2-pin AC plug mode'!
AC 220 ~ 230 Volts, 50/60 Hz
Australia model ..
AC 240 Volts, 50/60Hz
Multi-voitage model .
AC 110 V/129~127 V/220 V/240 V
(switchable), 50/60HZ
Power CONSUMPTION os ceeecesseccereseereseseseetcese
. 8330 W
Dimensions {including knobs and other prstdding parts)
- 420 (W) & 310 1D) & 110 (H) mm
Accessories
Remote control unit
Batteries (AA/REP) ...
Operating instructions
Power cord ....
mi ana
ro
NOTE:
Specifications and design subject to possible modification without
Notice, due to improvements.
* Measured by Audio Spectrum Analyzer.
MAINTENANCE OF EXTERNAL SURFACES
* Use a polishing cloth or dry cloth to wipe off dust and dirt.
* When the surfaces are very dirty, wipe with a soft cloth dipped in
some neutral cleanser diluted five or six times with water, and
wrung out well, and then wipe again with a dry cloth. Do not use
furniture wax or cleaners.
Never use thinners, benzine, insecticide sprays and other chemi-
cals on or near this unit, since these will corrode the surfaces.
VW
<ARB/034>
Advertisement
Table of Contents
