1. Manuals
  2. Brands
  3. NI Manuals
  4. Computer Hardware
  5. cRIO-9064
  6. Features

NI cRIO-9064 Features

Hide thumbs Also See for cRIO-9064:
Table of Contents

Advertisement

Quick Links

Download this manual
cRIO-9064
Features
2022-06-30

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the cRIO-9064 and is the answer not in the manual?

Questions and answers

Related Manuals for NI cRIO-9064

Summary of Contents for NI cRIO-9064

  • Page 1 Features 2022-06-30...

  • Page 2: Table Of Contents

    Configuring the cRIO-9064........

  • Page 3: Overview

    Data NI cRIO-9064 Configuring the cRIO-9064 You can connect the cRIO-9064 to a host computer or network and configure the startup options using the USB device port or the RJ-45 Gigabit Ethernet port 1 or port 2. Refer to the getting started guide on ni.com/manuals...
  • Page 4 & Automation Explorer (MAX) under the Network Settings tab. 1. Power on the host computer or Ethernet hub. 2. Connect the RJ-45 Gigabit Ethernet port 1 on the cRIO-9064 to the host computer or Ethernet hub using a standard Category 5 (CAT-5) or better shielded, twisted-pair Ethernet cable.

  • Page 5: Configuring Startup Options

    Enable Rebooting the cRIO-9064 with this setting on redirects the console output to the Console Out RS-232 serial port. You can use a serial-port terminal program to read the IP address and firmware version of the cRIO-9064.

  • Page 6: Crio-9064 Features

    Visit ni.com/info and enter the Info Code openssh for more information about SSH. LabVIEW Rebooting the cRIO-9064 with this setting on enables you to add the target to a Project LabVIEW project. Access cRIO-9064 Features The cRIO-9064 provides the following features.
  • Page 7 5. USB Host Port 6. Power Connector RJ-45 Gigabit Ethernet Ports The cRIO-9064 has two tri-speed RJ-45 Gigabit Ethernet ports. By default, both Ethernet ports are enabled and configured to obtain an IP address automatically. The Ethernet ports can be configured in MAX.
  • Page 8 151733-10 Related concepts Ethernet LED Indicators ■ Power Connector The cRIO-9064 has a power connector to which you can connect a power supply. The following table shows the pinout for the power connector. Table 4. Power Connector Pinout Pinout Description...
  • Page 9 Refer to the LabVIEW Help for information about the Serial VIs. Find examples on how to use NI-Serial or NI-VISA to perform serial communication in the NI Example Finder. The NI Example Finder is located on the Help menu in the LabVIEW Help.
  • Page 10 USB Flash drives, USB-to-IDE adapters, keyboards, mice, and USB cameras. Caution Do not hot-swap USB devices while the cRIO-9064 is in a hazardous location or connected to high voltages. If the cRIO-9064 is not in a hazardous location, you can connect and disconnect USB devices without affecting operation.

  • Page 11: Buttons

    RJ-45 Ethernet ports. Caution Do not hot-swap USB devices while the cRIO-9064 is in a hazardous location or connected to high voltages. If the cRIO-9064 is not in a hazardous location, you can connect and disconnect USB devices without affecting operation.
  • Page 12 Console Out. 2. Hold the RESET button again for 5 seconds to boot the controller into safe mode, enable Console Out, and reset network adapters to default settings. System Reset The following figure shows the reset behavior of the cRIO-9064. ni.com...

  • Page 13: Leds

    • RT Startup App disabled • FPGA Startup App disabled Press and hold RESET button for ≥ 5 s LEDs The cRIO-9064 provides the following LEDs. Figure 4. cRIO-9064 LEDs 1. POWER LED 2. STATUS LED 3. USER1 LED 4. USER FPGA1 LED 5.
  • Page 14 LED Pattern Indication Blinks twice and The cRIO-9064 is in safe mode. Software is not installed, which is the factory pauses default state, or software has been improperly installed on the cRIO-9064. An error can occur when an attempt to upgrade the software is interrupted.

  • Page 15: Chassis Grounding Screw

    The cRIO-9064 provides a chassis grounding screw. Figure 5. cRIO-9064 Chassis Grounding Screw 1. Chassis grounding screw For EMC compliance, you must connect the cRIO-9064 to earth ground through the chassis ground screw. Use wire that is 2.1 mm (14 AWG) solid copper wire with a maximum length of 1.5 m (5 ft).

  • Page 16: Internal Real-Time Clock

    The cRIO-9064 contains a lithium cell battery that stores the system clock information when the cRIO-9064 is powered off. There is only a slight drain on the battery when power is applied to the cRIO-9064 power connector. The rate at which the battery drains when power is disconnected depends on the ambient storage temperature.

  • Page 17: Mounting The Device

    You can also mount the cRIO-9064 in other orientations, on a nonmetallic surface, on a 35-mm DIN rail, on a desktop, or in a rack. Mounting the cRIO-9064 in these or other configurations can reduce the maximum allowable ambient temperature and can affect the typical accuracy of modules in the cRIO-9064.

  • Page 18: Dimensions

    Before using any of these mounting methods, record the serial number from the back of the cRIO-9064 so that you can identify the cRIO-9064 in the . You will be unable to read the serial number after you mount the cRIO-9064.

  • Page 19: Mounting Requirements

    Your installation must meet the following requirements for cooling and cabling clearance. Allow 25.4 mm (1.00 in.) on the top and the bottom of the cRIO-9064 for air circulation, as shown in the following figure. Figure 9. cRIO-9064 Cooling Dimensions 25.4 mm (1.00 in.)

  • Page 20: Mounting The Device Directly On A Flat Surface

    1. Location for measuring the ambient temperature Mounting the Device Directly on a Flat Surface For environments with high shock and vibration, NI recommends mounting the cRIO-9064 directly on a flat, rigid surface using the mounting holes in the cRIO-9064. What to Use cRIO-9064 ■...

  • Page 21: Mounting The Device On A Panel

    (1.86 in.) (1.20 in.) 47.0 mm (1.85 in.) 41.1 mm (1.62 in.) 4.1 mm (0.16 in.) Mounting the Device on a Panel You can use the NI panel mounting kit to mount the cRIO-9064 on a panel. © National Instruments...
  • Page 22 Complete the following steps to mount the cRIO-9064 on a panel. 1. Align the cRIO-9064 and the panel mounting plate. 2. Fasten the panel mounting plate to the cRIO-9064 using the screwdriver and M5 or number 10 screws. NI provides these screws with the panel mounting kit.

  • Page 23: Mounting The Device On A Din Rail

    (1.25 in.) (3.47 in.) 63.5 mm (2.50 in.) Mounting the Device on a DIN Rail You can use the NI DIN rail mounting kit to mount the cRIO-9064 on a standard 35- mm DIN rail. What to Use cRIO-9064 ■...
  • Page 24 Features 1. Align the cRIO-9064 and the DIN rail clip. 2. Fasten the DIN rail kit to the cRIO-9064 using the screwdriver and M4 × 25 flathead screws. NI provides these screws with the DIN rail mounting kit. Tighten the screws to a maximum torque of 1.3 N · m(11.5 lb · in.).

  • Page 25: Mounting The Device On A Rack

    DIN rail. Mounting the Device on a Rack You can use the following rack mount kits to mount the cRIO-9064 and other DIN rail-mountable equipment on a standard 482.6 mm (19 in.) rack. NI Sliding Rack-Mounting Kit, 779102-01 ■...
  • Page 26 Figure 14. Components of the NI Desktop Mount Kit 1. Desktop mounting brackets (x2) 2. Adapter bracket 3. M3x14 screws (x2) 4. M3x20 screws (x2) What to Do Complete the following steps to mount the cRIO-9064 on a desktop. ni.com...
  • Page 27 Features 1. Use a #1 Phillips screwdriver to remove the two screws from the back of the chassis on the front-panel side. 2. Use the screwdriver and the two M3x20 screws to attach the adapter bracket to the chassis.

  • Page 28: Ni Services

    Features Desktop Mounting Dimensions The following figures show the desktop mounting dimensions for the cRIO-9064. Figure 15. cRIO-9064 Desktop Mounting Front Dimensions 22.9 mm 17.2 mm (1.14 in.) (0.68 in.) 39.1 mm (1.54 in.) Figure 16. cRIO-9064 Desktop Mounting Side Dimensions 127.0 mm...

Table of Contents