Vax PowerWash VPW3, P86-P3-T - 2200W Series Pressure Washer Manual

Vax PowerWash VPW3, P86-P3-T - 2200W Series Pressure Washer Manual

Advertisement

Vax PowerWash VPW3, P86-P3-T - 2200W Series Pressure Washer Manual

Let's talk safety

Basic safety precautions

This pressure washer is intended for household use only and NOT for commercial or industrial use.

  • This pressure washer is for outdoor use only.
  • It is your responsibility to check the suitability of the surface to be cleaned. Vax cannot be held responsible for damage caused.
  • Keep fingers, hair and loose clothing from moving parts and openings whilst using the pressure washer.
  • When using the pressure washer the recommended working distance between the nozzle and surface area or object to be cleaned is 30cm.
  • This appliance can only be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Vax only recommend the use of Vax genuine accessories and detergent to be used with this pressure washer. The use of non-branded Vax accessories and detergent will invalidate your warranty.
  • For safe transportation, ensure that the pressure washer is unplugged and secure.

Don'ts

  • Don't leave the pressure washer unattended or running when not in use for more than 5 minutes without depressing the trigger.
  • Don't use the pressure washer if it has been dropped, damaged or immersed in water.
  • Don't use the pressure washer if the power cord or plug is damaged.
  • Don't handle the plug of the pressure washer with wet hands.
  • Don't use the pressure washer without supply hose (minimum length 7.5m) in place and unwind the hose fully from reel.
  • Don't use the pressure washer without the water filter in place.
  • Don't pull or carry the pressure washer by the power cord.
  • Don't use the power cord as a handle, pull the power cord around corners or sharp edges, or close a door over the power cord.
  • Don't unplug the pressure washer by pulling on the power cord.
  • Don't aim the pressure washer at people, animals, plants, electrical components, wires, or the pressure washer itself.
  • Don't use the pressure washer on electrical components, damaged/delicate paint surfaces, tyres, engines/motors.
  • Don't use the pressure washer with incorrect voltage as this may result in damage or injury to the user. The correct voltage is listed on the rating label.

Do's

  • Always wear suitable clothing, footwear and eye protection whilst using the pressure washer.
  • Always connect the water supply, remove the lance and squeeze the trigger to run water through the machine before switching the power on.
  • Always use a suitable hose connector to match the coupling on the pressure washer with a non-return valve at the tap end of the supply hose.
  • Always unplug the pressure washer before cleaning or carrying out any maintenance.
  • Always turn off and unplug the pressure washer before disconnecting or connecting the hose. After use always wrap the pressure hose and power cord around the storage clips provided.
  • Always release any built up pressure in the handle prior to disconnecting the hose and ensure water inlet filter is clean prior to storage in a cool dry place.
  • Use only CE approved 13amp extension cords with RCD, non-approved extension cords may overheat. Care should be taken to arrange the extension cord as it could be a trip hazard.
  • Always make sure the power/extension cord is fully unwound and prevent the power/extension cord from getting wet during use.
  • Always replace the fuse in the plug with a British 13amp fuse.
  • Always protect the power cable from heated surfaces or near open flames.
  • Always carry the pressure washer by the handle.
  • Always check the water hose and accessories are not damaged, broken or worn before use.

Included with your machine

Getting to know your machine

Overview

Technical Specification

Name PowerWash 2200W Complete
Model P86-P3-T
Voltage 220-240V~50Hz
Wattage 2200W
Max Pressure 160 bar
Rated Pressure 110 bar
Max Flow Rate 470L/Hr
Sound pressure level: LpA dB(A) 76
Sound power level: LwA dB(A) 94
LwA dB(A) K (uncertainty) 92
Vibration (m/s2) K (uncertainty) 0,5 m/s2 1,5

Accessories & Consumables

Universal Detergent
1-9-133398-00
Patio & Decking Detergent
1-9-133401-00
Wash & Protect Vehicle Detergent
1-9-133400-00
Subject to technical change without notice.
To purchase consumables and accessories, please visit vax.co.uk

Getting started

PLEASE READ 'LET'S TALK SAFETY' AT THE BEGINNING BEFORE USE.

Assembling your pressure washer

Attach both wheels and push until they click into place.

Attach the hose connector to water inlet by turning clockwise until tight.

Slot the handle in to the top of the machine and insert the 2 screws. Turn clockwise to tighten, making sure not to trap the detergent tube.

Always make sure the pressure washer and water supply is off before connecting or disconnecting the hose and accessories.


Always make sure the trigger safety lock is in the LOCKED position when not in use or connecting/ disconnecting the pressure hose.
Always check water hose, pressure hose, lance and accessories are not damaged, broken or worn before use.

Preparing your pressure washer for use

Push the pressure hose firmly to the water outlet and turn the pressure hose collar clockwise until tight.

A trigger safety lock is located underneath the handle. The safety lock should always be in LOCKED position before connecting/ disconnecting the pressure hose to the trigger handle.

To connect the pressure hose to the trigger handle, press the pressure hose release button and push the pressure hose to lock into position. Gently pull the pressure hose to check the connection.

Whilst firmly pushing the lance into the trigger handle turn clockwise to lock into position.

To remove the lance from the trigger handle firmly push and twist the lance anti-clockwise. When unlocked, pull to remove.

Tip
After connecting the pressure hose, lance and accessories check they are securely fitted and locked in place before turning on.

Using your machine


Always use an RCD (Residual Current Device) adaptor when using this pressure washer.

Don't leave the pressure washer running when not in use, or more than 5 minutes to prevent overheating.

Before switching the pressure washer on, the trigger handle must be squeezed to release water and any airlocks in the machine or pressure hose. Always release any pressure build up in the handle prior to disconnecting the hose.
Make sure the water supply is not connected. Firmly push the water hose pipe with suitable connector onto the water inlet to lock into position.

Connect the water hose pipe to a suitable water supply and turn the water on.

Before plugging the machine in, press the unlock safety button on the trigger handle and squeeze the trigger until water starts to flow through the nozzle.

Connect the power cord to the mains supply via an RCD adaptor.

Push switch to 'I' position to turn on. The machine will run for a few seconds then stop but no water will be released.

Squeeze the trigger on the trigger handle to release a high pressured water jet, and start cleaning.

Push switch to 'O' position to turn off.


Don't aim the pressure washer directly at people, animals, plants, electrical components, wires or the pressure washer itself.


Always make sure the machine is switched off and the safety button on the trigger handle is LOCKED before connecting/disconnecting the lance, nozzle or accessories.

Using your accessories

The jet nozzle has a wider spray and is ideal for use on surfaces such as cars, garden furniture, decking and boats.
To attach the jet nozzle, fit the lance with a firm push and twist clockwise to lock into place.

Hold down the release button on the lance, push the jet nozzle and lance firmly together until you hear an audible CLICK. Release the button and gently pull the jet nozzle to make sure it is locked securely before use.

Squeeze the trigger on the trigger handle to release a high pressured water jet, and start cleaning.
Using your accessories

The turbo nozzle has a more concentrated spray and is ideal for use on very dirty surfaces, patios or masonry. As it is not fitted with a pressure regulator it is not suitable for use on delicate or painted surfaces.
To attach the turbo nozzle, fit the lance with a firm push and twist clockwise to lock into place.

Hold down the release button on the lance, push the turbo nozzle and lance firmly together until you hear an audible CLICK. Release the button and gently pull the turbo nozzle to make sure it is locked securely before use.

Squeeze the trigger on the trigger handle to release a high pressured water jet, and start cleaning.


Never use the turbo nozzle on cars, tyres and engines.


When using detergent make sure you follow the dilution instructions and use Vax detergent only. Detergent can only be used with the trigger handle, lance and detergent nozzle, or car/outdoor/rotary brush if supplied. Detergent CANNOT be used with the jet and turbo nozzles.

Using detergent with your pressure washer

Unhook the detergent tube and insert into the detergent bag. Detergent is only dispensed with the trigger handle, lance and detergent nozzle or car/outdoor/ rotary brush if supplied.

Switch the pressure washer on and squeeze the trigger to dispense the water and detergent mix.
Using detergent with your pressure washer

After use, rinse the pressure washer to prevent blockages. Inset the detergent tube into a bucket of fresh water (Max 40°C), turn the machine on and squeeze the trigger for 1 minute.

Tip
Always make sure the pressure washer is switched OFF before connecting/disconnecting the pressure hose, lance, accessories or detergent bag.


When using your pressure washer the recommended working distance between the nozzle and surface area or object to be cleaned is 30cm.
After connecting the pressure hose, lance and accessories check they are securely fitted and locked in place before switching on.
Always release any pressure build up in the handle prior to disconnecting the hose and accessories.
Don't use if the lance and accessories are damaged, broken or worn.
Always check brushes are clean and free from grit/hard debris before use.

Using the patio brush (included in selected models only, see 'Included with your machine')

Push the extension tube onto the patio brush head and turn clockwise to secure. Twist and push the patio head collar to lock the extension tube into position.

Attach the extension tube onto the trigger handle, push firmly and twist clockwise to lock into place.
Using the patio brush - Step 1

Switch on the pressure washer and squeeze the trigger to release water spray.

To remove the extension tube from the trigger handle, firmly push and twist the extension tube anti-clockwise to unlock. Pull to remove.
Using the patio brush - Step 2

Tip
The extension tube can be used to extend all accessories and ideal for hard to reach areas and surfaces.
The outdoor brush is a soft bristled brush ideal for making easy work of cleaning garden furniture.
The car brush is a soft bristled brush and perfect for tackling tough dirt on delicate surfaces ideal for wheels and car mirrors.

Using the car brush (included in selected models only, see 'Included with your machine')

Attach the car brush to the trigger handle. Firmly push the car brush and trigger handle together, turn clockwise to lock into position.

Switch on the pressure washer and squeeze the trigger to release water spray or water and detergent mix.

To remove the brush from the trigger handle firmly push and twist the lance anti-clockwise to unlock. Pull to remove.

Using the outdoor brush (included in selected models only, see 'Included with your machine')

Attach the outdoor brush to the trigger handle. Firmly push the outdoor brush and trigger handle together, turn clockwise to lock into position.

Switch on pressure washer and squeeze trigger to release water spray or water and detergent mix.

To remove the outdoor brush from the trigger handle firmly push and twist the lance anti-clockwise to unlock. Pull to remove.

Using the rotary brush (included in selected models only, see 'Included with your machine')

Whilst firmly pushing the rotary brush into the trigger handle turn clockwise to lock into position.

Switch on pressure washer and squeeze trigger to release water spray or water and detergent mix.

To remove the rotary brush from the trigger handle firmly push and twist the lance anti-clockwise to unlock. Pull to remove.

Taking care of your machine


Always rinse fresh water through your pressure washer and accessories for 1 minute after using detergent to prevent blockages.

Maintenance

To access the water filter, unscrew water inlet connector and remove.

To remove the water filter, pinch the inner water filter tab with pliers and gently pull.

The water filter can be rinsed under running water periodically.


Before storing your machine always make sure no water remains in the pressure washer or hose/ accessories to prevent frost damage. Keep in a dry place above zero degrees and out of the reach of children.

Storage

Always store tools/cable/detergent tank into allocated slots.

Let's talk technical

Removing a blockage in the lance and nozzles

To remove the lance from the trigger handle firmly push and twist the lance anti-clockwise, when unlocked pull to remove.
Removing a blockage in the lance and nozzles

To remove the nozzle press the nozzle release button and pull.

Insert the nozzle cleaning tool into the end of the lance and nozzles to remove any dirt or debris.


Before carrying out any maintenance make sure the machine is switched off and unplugged.

What to do if it goes wrong

Problem Solution
There is an accessory missing
  • Check the contents panel on the box to make sure the part is included with your machine.
Why won't the pressure washer turn on?
  • Make sure the on/off switch is set to the 'I' position.
  • The plug may not be fully pushed into the electrical socket.
  • Check the fuse in the plug if this needs replacing, always replace with a British 13amp fuse.
  • Check if your RCD has been tripped, if it has tripped, reset it.
  • The power cord may be damaged.
Why won't the water/ detergent dispense?
  • The pump may have stopped, make sure the on/off switch is set to the 'I' position and check the plug fuse.
  • The pump may have stopped. This may be because of overheating due to poor water supply. Check the water flow rate to your water supply.
  • Hose may be blocked or kinked, check for leaks in the hose and clear any blockages. Straighten out the hose to ensure no kinks and check the hose pipe connections to the tap and water inlet.
  • There may be an air lock. To remove, unlock the trigger safety lock and squeeze the trigger to release water before the machine is switched on.
  • Check assembly of detergent application bottle. Go to 'Using your machine.' Nozzle/accessory may be blocked, clear any blockages and clean nozzle. Go to 'Lets talk technical.'
Why won't the pressure washer reach operating pressure?
  • Hose may be blocked or kinked, check for leaks in the hose and clear any blockages. Straighten out the hose to ensure no kinks and check the hose pipe connections to the tap and water inlet.
  • Nozzle may be blocked, clear any blockages and clean nozzle. Go to 'Lets talk technical.'
  • Remove and clean the water inlet filter. Go to 'Taking care of your machine.'
  • Check the water flow rate to your water supply.

Getting in touch

2 year guarantee*
It's quick and easy to register for your FREE
Online at: vax.co.uk/registration
Please retain your original receipt for proof of purchase.
We're here if you need us vax.co.uk/support
*Registration required. Terms and conditions apply, see vax.co.uk for details.

Accessories

Don't forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions

Universal detergent
Universal detergent to aid the break down and removal of stubborn dirt, moss, and grime.
1-9-133398-00
Patio & Decking detergent
Patio & decking detergent to aid the break down and removal of stubborn dirt from patio and decked areas.
1-9-133401-00
Wash & Protect vehicle detergent
Wash & protect vehicle detergent to aid the removal of road dirt, oil and grease from vehicles, and provide short term protection against weathering conditions.
1-9-133400-00
Standard lance
Standard lance connection between your trigger handle and attachments.
1-9-133749-00
Detergent nozzle
A detergent nozzle to directly apply detergent to surfaces to help loosen dirt, moss, and grime.
1-9-133759-00
Attachable detergent bottle
A detergent nozzle to directly apply detergent to surfaces to help loosen dirt, moss, and grime.
1-2-133752-00
Trigger handle
A smooth shape hand handle with an easy squeeze trigger and a built in safety lock for easy on/off trigger release.
1-2-133750-00
Jet nozzle
Jet nozzle to apply concentrated pressure to dislodge dirt and grime on all surface types.
1-9-133787-00
Turbo nozzle
A high pressure turbo nozzle to blast away tough embedded dirt from high traffic areas.
1-9-133753-00
Patio cleaning set
A large circular cased brush, supplied with an extension tube for cleaning concentrated areas quickly and efficiently. Ideal for: Patios, Decking, Driveways, Garage doors.
1-9-133767-00
Rotary brush
A firm bristled brush with 360 degree rotation, providing extra scrub power for an extra clean. Ideal for: Car alloy wheels, Car grills.
1-9-133767-00
Car brush
A soft bristled brush, perfect for agitating tough dirt from sensitive surfaces. Ideal for: Car mirrors, Car body.
1-9-133765-00
Outdoor brush
A handy outdoor brush, perfect for gently removing dirt from various outdoor surfaces. Ideal for: Garden furniture, Conservatories.
1-9-133769-00
Extension tube
An additional connection tube providing you extra reach.
1-9-133768-00
Replacement hose (10m)
An additional high pressure hose, highly durable and resistant to weather conditions.
1-9-133751-00

We're here if you need us Instead of taking me back to the shop, simply visit our online support: vax.co.uk/support

Still need to get in touch?
Our UK based Customer Care Team are here to support you.
For help with assembly, operational or performance problems, or buying and fitting new accessories, you can find all our contact details at vax.co.uk/contact

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Vax PowerWash VPW3, P86-P3-T - 2200W Series Pressure Washer Manual

Advertisement

Need Assistance?

Do you have a question about the PowerWash 2200W that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Table of Contents