Denon DRA-565RD Operating Instructions Manual page 10

ENGLISH
Using the Various Functions
1. Presetting stations in the memory
12
How to preset the memory
Memory block A : 1 to 8
Memory block B : 1to 8
Memory block C : 1 to 8
Memory block D : 1 to 8
Memory block E : 1 to 8
Auto Memory (FM only)
The DRA-565RD/DRA-365RD is equipped with an auto mem-
ory function.
Connect the antenna, set it so that stations can be received,
then hold in the MEMORY button and press the POWER button
to turn the power on. Stations for which the auto stop function
operates are stored in the preset memory in the order A1 to
A8, B1 to B8, and so on, through E8.
Channel A1 is tuned in after the auto memory operation is
completed.
Using this function makes it possible to find out the overall
reception conditions of the receivable stations. The memory
can be used effectively by recalling the channels in the preset
memory and replacing stations whose reception is poor with
stations whose reception is good, using the procedure de-
scribed in 1 above.
. Recalling preset stations
Use the SHIFT/PTY button ® to select memory block A, B, C, D
or E, then press the PRESET UP or DOWN button @® to recall
the station stored in the memory.
lf the PRESET UP or DOWN buttons are pressed without
pressing the SHIFT/PTY button @®, the stations are recalled in
the order A1 to A8, B1 to B8, and so on, through E8.
RDS search (for FM only)
Use this function to automatically tune to stations offering
Radio Data Service.
This operation is also possible by pressing the TUNER button
on the remote control unit once when the function is set to the
TUNER mode.
Operation Display
1. Press the RDS button @® once. RDS SEARCH
2. Press the PRESET UP or 4
DOWN button ®. "RDS SEARCH" flashes on the
display.
(Preset memory channels A1
to E8 are being searched.)
If no RDS station is found
with the above operation,
all the reception bands
are searched.
The station name is displayed
after searching stops.
3. Press the PRESET UP or RDS search starts again.
DOWN button again while
the RDS mark is flashing.
(If no other RDS station is found when all the frequencies are searched,
"NO RDS" is displayed.)
. PTY search (for FM only)
Use this function to find stations broadcasting a designated
type of programme type (PTY).
This operation is also possible by pressing the TUNER button
on the remote contro! unit twice when the function is set to the
TUNER mode. Next, press the PANEL button on the remote
control unit, select the PTY, then press the PRESET UP or
DOWN buttons to start the PTY search function in the specified
direction.
Operation Display
1. Press the RDS button twice. PTY SEARCH
4
Programme type or PTY
2. Press the SHIFT/PTY button.
Designated programme
type
(Always do this to designate the programme type if "PTY" is displayed
in step 1.)
3. Press the PRESET UP or
"PTY SEARCH"
flashes on the
DOWN button ®. display.
(Preset memory channels A1 to E8
are being searched.)
If there is no station broad-
casting the designated programme
type with the above operation,
all the reception bands are
searched.
The station name is displayed
after searching stops.
4, Press the PRESET UP or PTY search starts again.
DOWN button again while
the PTY mark is flashing.
{If no other station broadcasting the designated programme type is
found when all the frequencies are searched, "NO PROGRAMME"
is
displayed.)
* The programme
types which can be displayed are listed on
Page 13.
6. TP Search (for FM only)
Operation Display
1. Press the RDS button ® TP SEARCH
3 times.
2. Press the PRESET UP or "TP SEARCH" flashes on
DOWN button @. the display.
(Preset memory channels A1
to E8 are being searched.)
if no TP station is found
with the above operation,
all the reception bands are
searched.
The station name is displayed
after searching stops.
3. Press the PRESET UP or TP search starts again.
DOWN button again while
the TP mark is flashing.
7. Writing station names
You can write in station names yourself.
(Up to 8 characters)
(Refer to the table of characters on page 13.)
Operation Display
1, Press the RDS button First character flashes.
4 times.
2. Use the TUNING and First letter flashes.
DOWN buttons ® to
select the desired
characters.
3. Use the SHIF/PTY button Specified place flashes.
® to move to the
next place.
4. After writing the entire
station name, store it
in the memory.
(Refer to page 8.)
RDS Emergency Alarm
"ALARM" will flash on the display when the unit receives the Emergency
Programme Type Code (PTY31) from an RDS station.