Sharp FO-2600 Service Manual page 26

FO-2600TH/SG
FO-2600GU/GH
SW6 No. 4 Sender's information delivery -
When it is set at 0, senders name, sending page number and so on
are automatically printed in the recording paper on the receiving side
during transmission. Thus, the sender can be known on the receiving
side.
0: Apptied.
1: Not applied.
SW6 No. 5 ~ No. 8 Remote operation code figures by external
telephone(0-9)
Remote operation codes can be changed from 0 through 9. if set to
greater than 9, it defaults to 9. The is not changed and the new
function becomes, number programmed plus.
0000: 0
1001: 9
SW7 No. 1 H2 mode
This switch decides that receiving is executed in the H2 mode (15
seconds transfer mode).
If itis set at 1 (OFF), communication will not be executed in this mode
even though the sender is a H2 mode type.
0: Applied.
14: Not applied.
SW7 No. 2 ECM (MMH)
ECM SHARP's MH (MMH) mode enable or disable.
(MMH: Modified Modified Huffman)
0: Yes
1: No
SW7 No. 3 ECM mode
Used to determine ECM mode function. Refer to the following table.
Isw7-secmmove | | 0 |
[sw7-2ECMwMHMODE | _o | 1]
Compression ECM MMH mode | Yes | No |
method
SW7 No. 4 Reserved
Set to "0°.
SW7 No. 5 ~ No. 8 Modem signal transmission level (dBm)
The attenuation ratio of the signal sending level from the modem Is
set.
0000: 0 dBm
L
17171: -15 dBm
SW6 No. 1 ~ No. 4 Recall interval
Choice is made for redial interval for speed and rapid dials. Use a
binary number to program this. If set .to 0 accidentally, 2 will be
assumed. lf a number above 9 was entered, it will be set to 2. In this
case, it has to be corrected.
0001: 1 minute
+
1441: 15 minutes
SW8 No. 5 ~ No. 8 Recall times
A choice of redial attempts can be programmed. A binary number is
used to program it. If set to 0 by accident, the redial number will be
set to 5. if a number above 15 was set, it has to be corrected.
0001: 1 time
L
1111: 15 times
2-16
SW9 No. 1, No. 2 Dummy ringer rumbling time at TEL/FAX auto-
matic switching mode
The dummy ringer at TEL/FAX automatic switching mode is select-
able, :
00: 15 sec
01: 30 sec
10: 60 sec
11: 120 sec
SW9 No. 3 Busy tone detection continuation sound detect time
Selects detection of the continuous sound of 440Hz (SW11 No. 1) for
10 seconds or 5 seconds.
0: 5 seconds
1: 10 seconds.
SW9 No. 4, No. 5 Number of busy tone detection pulse
Used to set detection of Busy Tone continuous sounds.
SW9 No. 6 Busy tone detection tine (lower duration)
The initial value of detection is set according to electric condition. The
set value is changed according to the local switch board. (Erroneous
detection of sound is reduced.) Normally the upper duration is set to
750 ms, and the lower duration to 200ms. If erroneous detection is
caused by sound, etc. adjust the detection range. The lower duration
can be set in the range of 350ms to 300ms.
SWS No. 7 Busy tone detection time (upper duration)
Similarly to SW9 No. 6, the set value can be varied. The upper
duration can be set in the range of 650ms to 750ms.
00: 200ms-750ms
01: 200ms-650ms
10: 350ms-750ms
11: 350ms-650ms
SW9 No. 8 Busy tone intermittent sound detection
Line off detection is set.
0: Yes
1: No
SW10 No. 1, No. 2 Beep length select
Choice is made for end-buzzer of copy or communication end.
00: 3 sec
01; 1 sec
10: No beep
SW10 No. 3 Automatic reduce of copy
If set to 1, It is reduced automatically without being related to SW10
No. 5, No. 6.
SW10 No. 4 Automatic reduce of receive
If set to 1, It is reduced automatically without begin related to SW10
No. 7, No. 8.
SW10 No. 5, No. 6 Reduce of copy
It is reduced with each reduction rate in accordance with a document
size.
00: To print letter size document on record paper size sheet
(SW17 No. 4, 5)
01: To print A4 size document on record paper size sheet
(SW17 No. 4, 5)
10: To print legal size document on record paper size sheet
(SW17 No. 4, 5)
11: 100% (not accordance)
SW10 No. 7, No. 8 Reduce of receive
Similarly to SW10 No. 5, No. 6.