Table of Contents
Related Manuals for Magnimage LED-FW16-B
Summary of Contents for Magnimage LED-FW16-B
- Page 1 LED-FW16-B Video Control Ser ver V1.0 User Manual △ Before using this LED video processor, please read this instruction manual carefully and keep it for future reference. Document Version：V1.0 Document Release Date：2023/10/20 LED-FW16-B...
- Page 2 Statement Without the written permission of the company, no unit or individual may copy, transcribe or translate part or all of the contents of this manual.This manual shall not be distributed in any form or by any means (electronic,mechanical, photocopying, recording or other possible means) for commercial or commercial purposes.
-
Page 3: Table Of Contents
Directory Statement ............................1 Introduction ..........................2 Trademark Credit ..................................2 About the software ................................. 2 Product Features ..................................3 Port Extension ................................... 4 Safety Notice ..................................... 5 Features ............................6 Overview ..................................... 6 Technical Specifications ..............................10 Use Menu ............................ 12 How to use the buttons .............................. -
Page 4: Introduction
Introduction Thank you for purchasing our company's LED all-in-one video controller. Hope you can enjoy the excellent performance of this product. The design of this LED all-in-one video controller complies with international and industry standards, but improper operation may still cause personal injury and property damage. -
Page 5: Product Features
can carry maximum width 16380 pixels and maximum height 7680 pixels Support template save and load Support connection to MAGNIMAGE C-Link series receiver cards Support quick layer layout templet Support local USB flash drive for reading and loading configuration files ... -
Page 6: Port Extension
Support RS232 central control Support fiber input and fiber backup Support scrolling subtitle function Support time task function Support for output freezing Support button lock Port Extension LED-FW16-Bis basic model number，we can extend Input Source on the basis of basic model. -
Page 7: Safety Notice
Safety Notice The input voltage range of the power supply of this product is 100~240V, 50/60Hz, please use the correct power supply. When you want to connect or unplug any signal cable or control cable, please make sure that all power cables have been unplugged beforehand. When you want to add hardware devices to this product or remove hardware devices from this product, please make sure that all signal cables and power cables have been unplugged in advance. -
Page 8: Features
Features Overview The video control server is a video controller created by Magnimage, which integrates video processing, splicing, switching and LED screen sending card functions. This series integrates various professional input interfaces, supports up to 4K×2K/60Hz or 8K×1K/60Hz, LED-FW16-B single machine can load 10.40 million pixels, with bandwidth expansion enabled, a single machine... -
Page 12: Technical Specifications
1 x 10G fiber optic inputs Model Video Output Port Gigabit Ethernet 16 port ， single port load 0.98 million pixels, LED-FW16-B Port whole unit load 15.68 million pixels HDMI Loop Out Can loop out HDMI2.0 input source HDMI Monitor... - Page 13 Output Information Port Quantity Of Resolution Specification 16 port，single port load 0.98 million pixels, whole unit Gigabit Ethernet load 15.68 million pixels,a single machine can carry Port maximum width 16380 pixels and maximum height 7680 pixels HDMI2.0 LOOP Can loop out HDMI2.0 input source HDMI Monitor Output monitoring，1920x1080/60Hz 10G fiber optic interface, supporting replication or hot...
-
Page 14: Use Menu
Use Menu Using the product menu system can easily and intuitively set the machine to meet the user's use requirements The all-in-one video controller uses a full-color LCD display to display the entire user menu. When the user does not operate or the operation times out, the default state will be displayed on the LCD screen. -
Page 15: Layer Area
Browsing Mode Setting Mode ↖ confirm button, short press knob, can switch between the two modes. ↗ Under browse mode, Anticlockwise rotate the "knob", the cursor moves up or left; rotate the "knob" clockwise, the cursor moves down or right. When moving the cursor to the item to be adjusted, press the "knob"... -
Page 16: Input Area
INPUT Area： This area contains 12 buttons: Input1-8 button, EDID button, CROP button, Zoom button, INFO button The method of selecting signals is to first select the screen in the LAYER area, and then select the corresponding signal. The input has a signal, and the button light is white; The current selection is red. -
Page 17: Introduction To Default State
LCD screen of the front panel. After the startup is completed, the default state of the current machine will be displayed on the screen, as shown in the figure below： LED-FW16-B: The information in the above figure is explained as follows： Symbol... -
Page 18: Main Menu Introduction
" buttons, and knobs to select and adjust each item. The operating modes are shown in the table below: Operate Introduction In the default state, press the rotary knob or slide the "magnimage" in Open Main Menu the upper left corner Select each Item... -
Page 19: Main Menu
Main Menu In the default state, press the "OK" button or swipe the "magic" button in the upper left corner to enter the main menu state.and the LCD screen will display as shown in the figure below: There are 8 menu items in the main menu. Use the knob to select the 8 menu titles listed above. - Page 20 Connection Sequence:Quick Connection Sequence:Manual...
- Page 21 Udisk Operation： Manual Files By Local Flash：...
- Page 22 Read Rx Card Info: Rx Card Reset: supports EDID management and customize output Resolution resolution, single controller output max width can be LED Screen 16380 pixel，output max height can be 7680 pixel When all the network ports are routed in the same way, light the screen quickly according to the number Connection of cabinets, the connection of the network cable, the...
-
Page 23: Input
temperature of the receiving card Screen Large screen brightness (default value is 256) 100% Brightness Test Patten Range 1-10 When the cabinet label function is on, the led screen will display the serial Cabinet number of the network port and the serial number of the receiving card Label of each cabinet, so that the connection diagram can be made intuitively Bandwidth... - Page 24 HDMI/DP RGB Range：...
- Page 25 HDR_CFG： Input Ports Display the input information of all input ports on this device, with the List displayed content being input resolution or no signal All input signals from input 1 to input 7 can be intercepted at will. By selecting the input number and input signal that need to be intercepted through the knob or touch, you can enter the detailed operation menu for image capture.
- Page 26 Input signals from Input 1 to Input 6 can be set by selecting the knob Select the ring touch and click on the input number and signal that requires EDID to enter the detailed operation menu for EDID configuration Indicates the input sequence number and input signal DVI 1 currently being configured for EDID Horizontal...
-
Page 27: Layers
LAYERS LAYERS： ZOOM： LAYER OUTPUT AREA MAPPING： Monitor Config：... - Page 28 Layer Templates： Test Pattrerns Layer： Can change the horizontal position, vertical position, horizontal width, Size/Position vertical position of each layer Layer1~4 Select the layer that needs to be zoom Function Function off or Function on layer zoom Off/On Reset Reset layer zoom ZOOM Matching Match the corresponding horizontal/vertical reference...
-
Page 29: Picture
PICTURE Brightness：Range 0-100, default number is 50 Contrast：Range 0-100, default number is 50 Saturation：Range 0-100, default number is 50 Layers Pictures 4000K/5000K/6500K/7500K/8200K/9300K/10000K/11500 Setting K/user 9 modes Layer Color Red range 0-255, default 128 Temperature Green range 0-255, default 128 Blue range 0-255, default 128 Reset Reset to factory defaults... -
Page 30: Backup
BACKUP Backup Ports Setting： Local Backup Single machine can specify any network port for backup. When multiple machines are in the same LAN, you can Host choose another machine as backup or master, and set the Multi-Machin Machine IP address of another machine to achieve fast backup. e Backup Backup Set the IP address of the host on the backup machine... - Page 31 Ethernet Output Depend On Layer Signal： After being used as a multi machine backup, this function can be Ethernet Output used. When the layer signal is lost, a backup line switch is triggered, Depend On Layer and devices with the same group in the local area network will trigger Signal simultaneously Advert：The host is in one group when grouping, and the backup machine is in another...
- Page 32 Inputs Backup: Used for signal hot backup, after setting up the backup, if the current Inputs Backup input signal is lost, it will switch to the backup preset according to priority to prevent situations such as screen blackout after signal loss. Optical Fibew Output Setting：...
-
Page 33: Presets
PRESETS Delete All Preset： Task Schduler：... - Page 34 This machine can save 20 presets,Enter the loading interface, press the Save Preset number button or rotate the knob to load the preset This machine can save 20 presets,Enter the save interface, press the Load Preset number button or press the rotary knob to load the preset Enter the deletion interface, click the number buttons on the screen or Delete Preset press the rotary knob to delete the preset that has been saved...
-
Page 35: Misc
MISC Video Processor： Fiber Converter：... - Page 36 Label： Sync Lock Setting ： Screen Touch ：...
- Page 37 Date/Time： Status Info：...
- Page 38 Caption： Test Pattern Of LCD Screen：...
- Page 39 Factory Reset： IP Address Can change machine IP address Switch this mode, you can use the Communicatio Communicat square port USB communication USB Setting ion Setting Switch this mode, you can use the flat USB Disk File port USB to upgrade the machine Video Normal usage mode Processor...
-
Page 40: Language/语言
Direction Foreground 0-100 Transparency Background 0-100 Transparency Color preset: black background green text, black background red text, black background white text, white Subtitle Color background green text, white background red text, white background black text, and user options, users can customize it Set the horizontal and vertical starting Display Area... -
Page 41: Warranty
Warranty Machine Warranty Period 24 months from the date of the user's purchase invoice； If the user's purchase invoice is lost, the 60th day after the production date of this product is the start date of the warranty for this product. Non Warranty Faults or damages caused by abnormal use reasons such as stains or ...