Casio CELVIANO AP-6OR User Manual page 30

i £ START/STOP
Saving an Edited Pattern
# You can use this ptano's MIDI capabilities to save your original
accompaniment patterns to a coriputer or ather external storage
device, See "Buk Sending Piane Data" on page E-76 for details
* You can store up tn 6 accompaniment patterns in the user area, but
the actual number of patterns you will be able to store depends on
their sizes. If the patterns you store ace relatively large, memory
become full after fewer than 6 patterns are stored
Using the Pattern Create Mode
IMPORTANT! ===
The procedures in this section all assume that you lave read and are
familiar with the information under "Pattern Sequencer Basics" on
page E-52, and that you already know how to navigate between Pat-
tern Sequencer motes
Pattern Creation Techniques
«= Base Pattern Editing
Whie playing back tke part of a built-in pattern o: previously cre-
ated user pattern, you can add or delete notes, or completely de
lete a part and replace it with a new one.
+ From Seratch
With this method, you mnust input all the paris for all the elements
you want to use. With this method, you must use the procedure
under "Work Area Clear" or. page 5-58 to clear the Pattern Sequenc-
ec work area before you start recording
E-54
Indicates ne Pattern
Inaicates tre currently
Crvate Mode.
seieciad element
| {
PtaNorma |
£ %.. ele
t:
Original Kay
.2» Press the START/STOP button.
++ The selected element plays in a loop, repeating itself.
+ The display shows measure and beat numbers during ele-
ment playback
* You can pertorm the foliow-ng operations during element
playback.
+ Tempo changes
+ Part on and off
» Tone operations
= Mixer operations**
a
To stop playback, press the START/STOP button again.
ANOTESS
S50A-5- 058A
=——=—— IMPORTANT!
You cannot record accompaniment patterns converted using she
Pattem Conversion Disk. See "Using the Utillties" on page E-68 for
cetails.
Pawtern Creare Mode Currently selected element
Feames around the cranel numbers thal ccrrespand to
tne currently salecled parts Nash
+ Use the same procedures as thase described for step 2 under
"To play back elements of the accompaniment pattern in the
work area" on page E-54.
© To record the Rhythm part
Seiect a drurn sound. Use the DRUM SET TONE button or
tone number 192 through 199
@ To record the Bass part
Select a bass tone.
© To record Chord 1, 2, and 3 parts
Select a cherd tone. Use any tore besides the dcum. sounds.
we
* This causes the REC indicator to appear on the display.
4. select the parts you want to 'ecord.
+ Note that you cannat select paris once recording starts. Be
sure to select the pacts you want before you start recording.
5. Press the START/STOP button.
* At this time the REC indicator stops flashirg.
+ All parts of the selected element play back :n an endless loop
You can record rotes in the currently selected parts.
» Measure and beat rumters are shown an the display durng
recording
* Pressing any keyboard key starts actual recording.
@. Record in part in sequence.
+ You can perform the following operations during element
recording.
* Turn parts (channels) to be recorded on and off
+ Tempo changes
@ To record the Rhythm part
* Press the CHANNEL button CH10 to select the rhythm
part
« Use the keyboard to play the chythm part, Use the mea-
sure and beat values that appear on the display for tim:
ing.
@ To recard the Bass part
+ Press the CHANNE® button CH8 to select the dass part.
@ Yo record Choed 1, 2, and 3 pacts
«Use the CHANNEL buttons CH6, CH7, and CH® to setect
a chord part.
+ Use the keyboard to play the chord part. Use the measure
and beat values that appear on the display (or timing
This stops recording, which causes the REC indicator to dis-
appear from the displ
ENOTES #
E55