Qlightec ST45ML-NEC Manual

Increased Safety Explosion Proof LED Tower Lights
ST45ML-NEC
20 40
Ex
54
Thank you for purchasing Qlight's products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Safety Precautions for Explosion Proof Products
Please follow the instruction below to ensure safe and correct use of explosion proof products.
1. Explosion proof products should be managed according to explosion-proof regulations. Do not disassemble, assemble, alter or repair the
product arbitrarily.
2. The temperature rating of the product is the temperature the product will experience at the applied rated voltage and ambient temperature
indicated.
3. Use cable glands that satisfy the product's explosion proof grade and temperature grade.
4. Unused cable entries must be filled with material that meets the explosion proof grade and temperature rating.
5. Before installing the product, please make sure all cautions indicated on the labels, packaging, and operation manual of the product are
fully understood.
6. Installation, maintenance and repair of the product must be performed by experts in the explosion proof field, or persons who have
received relevant training.
7. For safety, the product should be installed and operated in environments that avoid high temperature and high pressure.
8. Please follow general safety precautions and avoid installing the product in locations that may generate excessive heat.
9. When installing the product in places where chemicals are located, please make sure that the environment does not have two or more
incompatible chemicals mixed. For safety, please read the instruction manual carefully and be mindful of the chemical compositions
where the product is used.
10. This product requires grounding.
11. The equipment shall be supplied by an appropriately rated transient protective device that is set to a level not exceeding 140% of the
peak rated voltage.
12. The use of the isoloating source and ratings of the overcurrent protective device(3 Amps as per 22AWG) required to be installed in the field.
Specific conditions of use
1. The equipment enclosure shall not be opened when an explosive atmosphere is present and shall be used in an area of at least Pollution
degree 2 as defined in IEC 60664-1.
2. The equipment shall be supplied by an appropriately rated transient protective device that is set to a level not exceeding 140% of the peak
rated voltage.
3. The equipment includes external non-metallic parts. the user shall therefore ensure that the equipment is not installed in a location where
it may be subjected to external conditions which might cause a build-up of electrostatic charges on non-conducting surfaces. Additionally,
cleaning of the equipment shall be done with a damp cloth.
4. External earthing connection shall be established by end-user via prepared M4 bolt and cable with a diameter greater than 4mm
External earthing connection shall be corrosion resist.
Precaution for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. During wiring or maintenance, please completely turn off the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a fire to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point.
(Failure to follow these instructions may lead to fire, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to fire, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device.
(Failure to follow this may cause damage to property, fire, electric shock and loss of life.)
Precaution for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn off the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product's specification.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Static electricity may be generated by physical contact due to the surface characteristics of this product so please use a wet towel
or anti-static cleaner to remove the foreign substances on the product.
Please scan the QR code for more
detailed product information.
www.qlight.com
1
.
2