Nominal Data; Data According To Commission Regulation (Eu) 327/2011; Technical Description - ebm-papst VBH0630CTTRS Operating Instructions Manual

8300100048
VBH0630CTTRS

3.2 Nominal data

Motor E15034-120
Phase 3~
Nominal voltage / VAC 400
Nominal voltage 380 .. 480
range / VAC
Frequency / Hz
50/60
Method of obtaining ml
data
Status prelim.
Speed (rpm) / min -1 1910
Power consumption / W
5850
Current draw / A 9.0
Min. ambient -40
temperature / °C
Max. ambient 40
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
01 Overall efficiency η / %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P / kW 5.75
ed
09 Air flow q / m³/h
v
09 Pressure increase total p /
fs
Pa
10 Speed (rpm) n / min -1
11 Specific ratio *
12 Recycling/disposal
13 Maintenance
14 Additional components
* Specific ratio = 1 + p / 100 000 Pa
fs
Data obtained at optimum efficiency level. The efficiency values displayed for achieving
conformity with the Ecodesign Regulation EU 327/2011 has been reached with defined air
duct components (e.g. inlet rings). The dimensions must be requested from ebm-papst. If
other air conduction geometries are used on the installation side, the ebm-papst evaluation
loses its validity/the conformity must be confirmed again. The product does not fall within
the scope of Regulation (EU) 2019/1781 due to the exception specified in Article 2 (2a)
(motors completely integrated into a product).
Item no. 1170000721 · ENU · Change 262664 · Approved 2022-10-26 · Page 5 / 16
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Actual Req. 2015
75.7 59.5
A
Static
78.2 62
Yes
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart ·
HRA 590344
D-74673 Mulfingen
8300100048
15840
956
1910
1.01
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.

3.4 Technical description

Size 630 mm
Motor size 150
Rotor surface
Painted black
Electronics housing Die-cast aluminum
material
Impeller material PP plastic
Support plate material Sheet steel, galvanized
Support bracket Steel, painted black
material
Inlet nozzle material ABS plastic
Number of blades 5
Direction of rotation Clockwise, viewed toward rotor
Degree of protection IP55
Insulation class
"F"
Moisture (F) / H1
Environmental (H)
protection class
Ambient temperature Occasional start-up at temperatures
note between -40°C and -25°C is permitted.
For continuous operation at ambient
temperatures below -25°C (such as
refrigeration applications), use must be
made of a fan design with special low-
temperature bearings.
Installation position See legend on product drawing
Condensation On rotor side
drainage holes
Mode S1
Motor bearing Ball bearing
Technical features
- Operation and alarm display with LED
- External 15-50 VDC input
(parameterization)
- Alarm relay
- Integrated PI controller
- Configurable inputs/outputs (I/O)
- MODBUS V6.3
- Motor current limitation
- RS-485 MODBUS-RTU
- Soft start
- Voltage output 3.3-24 VDC, Pmax =
800 mW
- Control interface with SELV potential
safely disconnected from the mains
- Thermal overload protection for
electronics/motor
- Line undervoltage / phase failure
detection
- Vibration sensor
Touch current <= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup Terminal box
Motor protection Electronic motor protection