1. Manuals
  2. Brands
  3. evertz Manuals
  4. Enclosure
  5. 7700 Series
  6. Manual

evertz 7700 Manual

Standalone module enclosure
Hide thumbs Also See for 7700:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
1.
OVERVIEW ........................................................................................................................... 1
2.
INSTALLATION .................................................................................................................... 1
2.1.
POWER ....................................................................................................................................... 1
2.2.
REMOVING THE FRONT COVER .............................................................................................. 1
2.3.
RACK MOUNTING THE STANDALONE ENCLOSURES .......................................................... 2
3.
UPGRADING FIRMWARE.................................................................................................... 3
3.1.
UPDATE PROCEDURE .............................................................................................................. 3
3.1.1.
PART 1: Configuring the Module for Firmware Upgrades.................................................... 3
3.1.2.
PART 2: Terminal Program Setup ....................................................................................... 4
3.1.3.
PART 3: Uploading the New Firmware ................................................................................ 4
3.1.4.
PART 4: Completing the Upgrade........................................................................................ 5
Tables
Table 3-1: Evertz Serial Upgrade Cable (WA-S76)............................................................................................. 3
Figures
Figure 2-1 : Mounting the S7701FR into the Rack Mount Tray .......................................................................... 2
TABLE OF CONTENTS
Revision 2.2
7700 Multiframe Manual
Standalone Module Enclosure
S7701FR - i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 7700 and is the answer not in the manual?

Questions and answers

Related Manuals for evertz 7700

Summary of Contents for evertz 7700

  • Page 1 PART 3: Uploading the New Firmware ................4 3.1.4. PART 4: Completing the Upgrade..................5 Tables Table 3-1: Evertz Serial Upgrade Cable (WA-S76)..................... 3 Figures Figure 2-1 : Mounting the S7701FR into the Rack Mount Tray ................2 S7701FR - i...
  • Page 2 Jan 08 Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof or for the rights of third parties, which may be effected in any way by the use thereof. Any representations in this document concerning performance of Evertz products are for informational use only and are not warranties of future performance, either express or implied.
  • Page 3 DC power adapter(s) for about 10 seconds and then reapply power to the unit. If the condition that caused the fuse to trip still exists the fuse will trip again. In this case you should contact Evertz customer service for instructions on how to proceed.
  • Page 4 7700 Multiframe Manual Standalone Module Enclosure 2.3. RACK MOUNTING THE STANDALONE ENCLOSURES Up to 3 of the S7701FR enclosures can be conveniently mounted in the S7701FR-RP rack mount panel. First remove the front cover as described in section 2.2. Then slide the enclosure into the rack mount panel as shown in Figure 2-1 and secure with the four screws provided.
  • Page 5 1. Remove the module from the frame. 2. Connect the Evertz Serial Upgrade cable to the 2 row x 3 pin header on the front edge of the 7700 series module as shown in the manual chapter for the module. Install the cable with the ribbon cable towards the front of the board.
  • Page 6 Data bits Stop bits Flow Control None 7. Install the 7700 module into the frame. After the module powers up, a banner with the boot code version information should appear in the terminal window. For example: EVERTZ MFC5407 MONITOR 2.1.3 COPYRIGHT 1997, 1998, 1999, 2000, 2001, 2002 EVERTZ MICROSYSTEMS LTD.
  • Page 7 12. You can now close the terminal program and disconnect the RS-232 serial cable from the PC. 13. Remove the module from the frame and disconnect the 7700 Serial Upgrade cable from the module. Restore the UPGRADE jumper to the RUN position.
  • Page 8 7700 Multiframe Manual Standalone Module Enclosure This page left intentionally blank S7701FR - 6 Revision 2.2...

This manual is also suitable for:

S7701fr

Table of Contents