Pioneer XR-A330 Operating Instructions Manual page 2

CAUTION
This product contains a laser diode of higher class than 1.
To ensure continued safety, do not remove any covers or
attempt to gain access to the inside of the product.
Refer all servicing to qualified personnel.
The following caution label appears on your unit.
Location: rear of the unit
IMPORTANT
FOR USE IN THE UNITED
KINGDOM
The wires in this mains lead are coloured in
accordance with the following code:
Blue: neutral
Brown: live
If the plug provided is unsuitable for your socket outlets, the
The cut-off plug should be disposed of and must not be
inserted into any 13 amp socket as this can result in electric
shock. The plug or adaptor of the distribution panel shouldbe
provided witha 5 amp fuse. As the colours of the wires in the
mains lead of this appliance may not correspond with coloured
markings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
CLASS 1
LASER PRODUCT
Do not connect either wire to the earth terminal of a three-
pin plug.
NOTE
After replacing or changing a fuse, the fuse cover in the plug
must be replaced with a fuse cover which corresponds to
the colour of the insert in the base of the plug or the word
that is embossed on the base of the plug, and the appliance
must not be used without a fuse cover. if lost, replacement
fuse covers can be obtained from your dealer.
Only 5 A fuses approved by B.S.I. or A.S.T.A. to B.S. 1362
plug must be cut off and a suitable plug fitted.
Demo Function
< XR-A330, XR-A550, XR-A660 >
The Demo mode starts automatically when the power cordis plugged
into the power outlet.
Also, when the P.BASS (DEMO) button is pressed for more than 3
seconds in the STANDBY mode, the Demo mode is activated.
In the demo mode, various functions of this system appear on the
display. :
@ The Demo mode can be cancelled by pressing the STANDBY/ON
button or function button.
e@ When the P.BASS (DEMO) button is pressed for more than 3
seconds in the demonstrate mode, the demonstration stops and
the demonstration function is cancelled. When the demonstration
function is cancelled, the demonstration is not carried out even
when the power cord is connected again. To resume
demonstration function, press the P.BASS (DEMO) button for
more than 3 seconds in the standby mode.
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know
how to operate your model properly. After you have finished reading
the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power
outlet may sometimes differ from that shown in the explanatory
drawings. However, the method of connecting and operating the unit
is the same.
Isle chee de adainonerl he
Install the unit in a well-ventilated location where it will not
be exposed to high temperatures or humidity.
Do not install the unit in a location which is exposed to direct rays of
the sun, or near stoves or radiators. Excessive heat can adversely
affect the cabinet and internal components. Installation of the unit in
a damp or dusty environment may also result in a malfunction or an
accident (avoid installation near cookers, etc., where the unit may be
exposed to oily smoke, steam or heat).
Ventilation
When installing this unit, make sure to leave space around the unit for
ventilation to improve heat radiation (at least 30 cm at top, 15 cm at
rear, and 15 cmat each side). If not enough space is provided between
the unit and walls or other equipment, heat will build up inside,
interfering with performance or causing malfunctions.
2
<XRE3014>
En
should be used.
< XR-A770 >
The Demo mode starts automatically when the power cordis plugged
into the power outlet.
Also, when the BALANCE (DEMO) button is pressed for more than 3
seconds in the STANDBY mode, the Demo mode is activated.
In the demo mode, various functions of this system appear on the
display.
@ The Demo mode can be cancelled by pressing the STANDBY/ON
button or function button.
e@ When the BALANCE (DEMO) button is pressed for more than 3
seconds in the demonstrate mode, the demonstration stops and
the demonstration function is cancelled. When the demonstration
function is cancelled, the demonstration is not carried out even
when the power cord is connected again. To resume
demonstration function, press the BALANCE (DEMO) button for
more than 3 seconds in the standby mode.
THE POWER SWITCH IS SECONDARY CONNECTED AND
THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS
POWER IS THE STANDBY POSITION.
Precautions regarding installation
Placing and using the unit for long periods on heat-generating
sources will affect performance. Avoid placing the unit on heat-
generating sources.
Install the unit as far away as possible from your TV. Installation in
close proximity to such equipment may cause noise or degradation
of the picture.
Such noise may be particularly noticeable when an indoor antenna
is used. In such cases, make use of an outdoor antenna, or turn off
the power to the unit.
Please place this unit on a level surface.
Condensation
When this unit is brought into a warm room from previously cold
surroundings or when the room temperature rises sharply,
condensation may form inside, and the unit may not be able to attain
its full performance. To prevent this, allow the unit to stand for about
an hour before switching it on, or raise the room temperature
gradually.