Related Manuals for Coremorrow S21
Summary of Contents for Coremorrow S21
- Page 1 S21 Piezo Rotation Stage User Manual Version: V1.0 This document describes the following products: ■ S21.R7S ■ S21.R7K...
- Page 2 DECLARATION This user manual is applicable to S21 piezo rotation stage, for your smooth and correct use of this product, please read this manual carefully before using it. Please follow the instructions in the installation and use process. Improper operation may cause injury to the operator and/or damage to the...
-
Page 3: Table Of Contents
Contents 1. Introduction ............................2 1.1 Purpose and content ........................2 1.2 Symbol and meaning ........................2 1.3 Users of This Manual ........................2 1.4 Manual Lost and Reissued ......................2 2. Safety Guide ............................3 3. Product Overview ...........................4 3.1 Product Introduction ........................4 3.2 Product Features ........................5 3.3 Motion direction ........................5 4. -
Page 4: Introduction
The default user of this manual has knowledge of piezoelectric products and controllers, and has a certain basis for their installation and use. 1.4 Manual Lost and Reissued If this manual is lost, please contact CoreMorrow. We will send you the latest version of the user manual. -
Page 5: Safety Guide
2. Safety Guide S21 piezo rotation stage is designed with the most advanced technology and safety standards for your own safety and the correct use of the product, please observe the following points when in use. A change in temperature and pressure will charge the piezoelectric actuator, and... -
Page 6: Product Overview
S21 piezo rotation stage has the following advantages: High performance piezo stack: S21 piezo rotation stage is driven by a highly reliable ceramic actuator with a fully insulated structure, so its performance and service life are far better than the traditional actuator. -
Page 7: Product Features
S21 is mainly used in biotechnology, interferometry, quality detection, optical detection, nanometer positioning, microscopy and imaging, image processing and other fields, with a very good development prospect. 3.2 Product Features Large rotation angle. Closed loop strain gauge sensor, high positioning accuracy. -
Page 8: Installation And Operation
2.Mount M3 on the mounting surface directly and tighten it; 3.Mounting the load and tighten it properly to ensure the positioning accuracy; 4.Connect the S21 connector with the corresponding controller according to the identification at the connector; The wiring mode of LEMO connector is shown as below:... -
Page 9: Load
When mounting the load, ensure that the load quality is less than the maximum load capacity of S21, and try to mount the load in the center of the moving surface. The correct position to mount the load is shown below. - Page 10 S21 Piezo Rotation Stage User Manual It is forbidden to mount the load on one side of the moving platform, which will cause serious damage to the product, as shown in the figure below. FIG.6 Do not mount long loads on one side of the platform...
-
Page 11: Operating
Avoid stretching and bending cables. Use the dedicated cable provided by CoreMorrow to connect S21 and the controller. Do not connect via an extension cable casually, if you need a longer cable, please contact CoreMorrow. -
Page 12: Transportation And Inspection
150V). 5.After use, please carry out voltage reset operation. Please take light steps when S21 in operation, do not knock the product, so as not to affect the use of the product or even damage the product. In order to achieve better motion precision of S21, it is recommended to use our company's supporting controller. -
Page 13: Open-Box Inspection
6.2 Open-Box Inspection Inspection content: Before opening the package, please check the outer packing carefully to see if there is any breakage, wetting, dampness, deformation, etc. Please check the completeness of package contents one by one according to the supply contract and packing list. Check whether the surface of the product has obvious damage. -
Page 14: Daily Maintenance
Table 1 FAQ and solutions If the user cannot solve the problem by himself in the process of using, please record the problem in detail and contact CoreMorrow, and professional technical personnel will help to solve. Problems caused by improper operation are not covered by the warranty. -
Page 15: Disposal
In order to fulfill our responsibility as a product manufacturer, we will dispose all old equipments on the market in an environmentally friendly manner. If you have equipment that cannot be disposed, you can ship it to CoreMorrow. Address: Building I2, No.191 Xuefu Road, Nangang District, Harbin, HLJ, China Tel: +86-451-86268790 8. -
Page 16: Customer Service
S21 Piezo Rotation Stage User Manual 9.Customer Service If you have questions about the products you are currently using, please let us know the following information: Product model and relevant number The controller model Software driver version Computer operating system that installs supporting software 10.Contact us...
Need help?
Do you have a question about the S21 and is the answer not in the manual?
Questions and answers